Home
Главная
Dremel
Граверы и мини-дрели
8220 5/65 RUS F0138220JN
Инструкция по эксплуатации Страница: 23

Dremel 8220 5/65 RUS F0138220JN [23/56] This charger can be used by children aged 8 and above and by persons who have physical sensory or mental limitations or a lack of experience or knowledge if a person responsible for their safety supervises them or has instructed them in the safe operation of the charger and they understand the associated dangers supervise children cleaning and user

loss of control, loose rotating components will be

violently thrown.

o. Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

p. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

q. Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, sanding band, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the material

causing the wheel to climb out or kick out. The wheel may

either jump toward or away from the operator, depending

on direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

a. Maintain a rm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. The operator can control kickback forces, if

proper precautions are taken.

b. Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have

a tendency to snag the rotating accessory and cause

loss of control or kickback.

c. Do not attach a toothed saw blade. Such blades

create frequent kickback and loss of control.

d. Always feed the bit into the material in the same

direction as the cutting edge is exiting from the

material (which is the same direction as the chips

are thrown). Feeding the tool in the wrong direction

causes the cutting edge of the bit to climb out of the

work and pull the tool in the direction of this feed.

e. When using rotary les, cut-off wheels, high-speed

cutters or tungsten carbide cutters, always have

the work securely clamped. These wheels will grab

if they become slightly canted in the groove, and can

kickback. When a cut-off wheel grabs, the wheel itself

usually breaks. When a rotary le, high-speed cutter

or tungsten carbide cutter grabs, it may jump from the

groove and you could lose control of the tool.

SAFETY WARNINGS SPECIFIC FOR GRINDING AND

ABRASIVE CUTTING-OFF OPERATIONS

a. Use only wheel types that are recommended

for your power tool and only for recommended

applications. For example: do not grind with the

side of a cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied to

these wheels may cause them to shatter.

b. For threaded abrasive cones and plugs use only

undamaged wheel mandrels with an unrelieved

shoulder ange that are of correct size and length.

Proper mandrels will reduce the possibility of breakage.

c. Do not “jam” a cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or snagging of

the wheel in the cut and the possibility of kickback or

wheel breakage.

d. Do not position your hand in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your hand, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

e. When wheel is pinched, snagged or when

interrupting a cut for any reason, switch off the

power tool and hold the power tool motionless until

the wheel comes to a complete stop. Never attempt

to remove the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate the

cause of wheel pinching or snagging.

f. Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind, walk

up or kickback if the power tool is restarted in the

workpiece.

g. Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

h. Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

SAFETY WARNINGS SPECIFIC FOR

WIRE

BRUSHING

OPERATIONS

a. Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress

the wires by applying excessive load to the brush.

The wire bristles can easily penetrate light clothing

and/or skin.

b. Allow brushes to run at operating speed for at least

one minute before using them. During this time no

one is to stand in front or in line with the brush.

Loose bristles or wires will be discharged during the

run-in time.

c. Direct the discharge of the spinning wire brush

away from you. Small particles and tiny wire

fragments may be discharged at high velocity during

the use of these brushes and may become imbedded

in your skin.

d. Do not exceed 15,000 RPM when using wire

brushes.

WARNING

DO NOT WORK WITH MATERIALS

CONTAINING ASBESTOS (ASBESTOS

IS CONSIDERED CARCINOGENIC).

WARNING

TAKE PROTECTIVE MEASURES

WHEN DURING WORK DUST CAN

DEVELOP THAT IS HARMFUL TO ONE’S HEALTH,

COMBUSTIBLE OR EXPLOSIVE (some dusts are

considered carcinogenic); wear a dust mask and work

with dust/chip extraction when connectable.

ENVIRONMENT

DISPOSAL

The machine, accessories and packaging should be sorted

for environmental-friendly recycling.

ONLY FOR EC COUNTRIES

Do not dispose of power tools into household

waste!

According the European Guideline 2012/19/EC for

Waste Electrical and Electronic Equipment and its

implementation into national right, power tools

that are no longer usable must be collected

separately and disposed of in an environmentally

correct manner.

SPECIFICATIONS

GENERAL SPECIFICATIONS

Voltage Rating .........12 V MAX

Amperage Rating ......1,3 – 2,0 Ah

Rated Speed ..........n 33000 min

-1

Collet Capacity ........ 0,8 mm, 1,6 mm, 2,4 mm,

3,2 mm

SPECIFICATIONS CHARGER

Input. . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W

Output ...............3,6 V - 12 V

Weight ...............292Gr

EXTENSION CORDS

Use completely unrolled and safe extension cords with a

capacity of 5 Amps.

CHARGING AND BATTERIES

• This charger can be used

by children aged 8 and

above and by persons who

have physical, sensory or

mental limitations or a lack

of experience or knowledge

if a person responsible for

their safety supervises them

or has instructed them in the

safe operation of the charger

and they understand the

associated dangers

• Supervise children

• Cleaning and user

Содержание

Похожие устройства