Home
Главная
Makita
Сетевая торцовочная пила
LS0815FL
Инструкция по эксплуатации Страница: 18

Makita LS0815FL [18/124] Carrying tool

Molding

position in

Fig. A

Molding edge against

guide fence

(1)

Ceiling contact edge should

be against guide fence.

Ceiling contact edge should

be against guide fence

For

outside

corner

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

For inside

corner

Wall contact edge should be

against guide fence

Finished piece

(2)

(3)

(4)

Table (B)

006362

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° LEFT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its CEILING CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will

always be on the LEFT side of the

blade after the cut has been made.

7. Cutting aluminum extrusion

Fig.37

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a

cutting lubricant when cutting the aluminum

extrusion to prevent build-up of the aluminum

material on the blade.

WARNING:

• Never attempt to cut thick or round aluminum

extrusions. Thick or round aluminum extrusions

can be difficult to secure and may work loose

during the cutting operation which may result in

loss of control and serious personal injury.

8. Wood facing

Use of wood facing helps to assure splinter-free

cuts in workpieces. Attach a wood facing to the

guide fence using the holes in the guide fence.

See the figure concerning the dimensions for a

suggested wood facing.

15mm Over 450 mm

62mm-65mm

18 mm

45mm

103mm 65mm 103mm

014279

CAUTION:

• Use straight wood of even thickness as the wood

facing.

WARNING:

• Use screws to attach the wood facing to the

guide fence. The screws should be installed

so that the screw heads are below the surface

of the wood facing so that they will not

interfere with the positioning of the material

being cut. Misalignment of the material being cut

can case unexpected movement during the cutting

operation which may result in a loss of control and

serious personal injury.

NOTICE:

• When the wood facing is attached, do not turn the

turn base with the handle lowered. The blade

and/or the wood facing will be damaged.

9. Groove cutting

Fig.38

A dado type cut can be made by proceeding as

follows:

Adjust the lower limit position of the blade using

the adjusting screw and the stopper arm to limit

the cutting depth of the blade. Refer to "Stopper

arm" section described previously.

After adjusting the lower limit position of the blade,

cut parallel grooves across the width of the

workpiece using a slide (push) cut as shown in the

figure. Then remove the workpiece material

between the grooves with a chisel.

WARNING:

• Do not attempt to perform this type of cut by

using a wider type blade or dado blade.

Attempting to make a groove cut with a wider

blade or dado blade could lead to unexpected

cutting results and kickback which may result in

serious personal injury

• Be sure to return the stopper arm to the

original position when performing other than

groove cutting. Attempting to make cuts with the

stopper arm in the incorrect position could lead to

unexpected cutting results and kickback which

may result in serious personal injury.

CAUTION:

• Be sure to return the stopper arm to the original

position when performing other than groove

cutting.

Carrying tool

Fig.39

Make sure that the tool is unplugged. Secure the blade

at 0° bevel angle and the turn base at the full right miter

angle position. Secure the slide poles so that the lower

slide pole is locked in the position of the carriage fully

pulled to operator and the upper poles are locked in the

1. Holes

Makita LS0815FL [18/124] Carrying tool

Содержание

Похожие устройства