Home
Главная
Makita
Сетевая торцовочная пила
LS0815FL
Инструкция по эксплуатации Страница: 19

Makita LS0815FL [19/124] Maintenance

position of the carriage fully pushed forward to the guide

fence (refer to the section titled "Slide lock adjustment

".) Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin.

Wind the power supply cord using the cord rests.

WARNING:

• Stopper pin is only for carrying and storage

purposes and should never be used for any

cutting operations. The use of the stopper pin for

cutting operations may cause unexpected

movement of the saw blade resulting in kickback

and serious personal injury.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily.

CAUTION:

• Always secure all moving portions before carrying

the tool. If portions of the tool move or slide while

being carried loss of control or balance may occur

resulting in personal injury.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off

and unplugged before attempting to perform

inspection or maintenance. Failure to unplug

and switch off the tool may result in accidental

start up of the tool which may result in serious

personal injury.

•

Always be sure that the blade is sharp and clean

for the best and safest performance.

Attempting a

cut with a dull and /or dirty blade may cause kickback

and result in a serious personal injury.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or

the like. Discoloration, deformation or cracks may

result.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle

Fig.40

Push the carriage toward the guide fence and

tighten the locking screw to secure the carriage.

Loosen the grip which secures the turn base. Turn

the turn base so that the pointer points to 0° on the

miter scale. Then turn the turn base slightly

clockwise and counterclockwise to seat the turn

base in the 0° miter notch. (Leave as it is if the

pointer does not point to 0°.) Loosen the hex

sockets bolts securing the guide fence using the

socket wrench.

Fig.41

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the

side of the blade with the face of the guide fence

using a triangular rule, try-square, etc. Then

securely tighten the hex socket bolts on the guide

fence in order starting from the right side.

Fig.42

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen

the screw which secures the pointer and adjust the

pointer so that it will point to 0°.

2. Bevel angle

(1) 0° bevel angle

Fig.43

Push the carriage toward the guide fence

and tighten the locking screw to secure the

carriage. Lower the handle fully and lock it in

the lowered position by pushing in the

stopper pin. Loosen the lever at the rear of

the tool.

Fig.44

Turn the hex bolt on the right side of the arm

two or three revolutions counterclockwise to

tilt the blade to the right.

Fig.45

Carefully square the side of the blade with

the top surface of the turn base using the

triangular rule, try-square, etc. by turning the

hex bolt on the right side of the arm

clockwise. Then tighten the lever securely.

Fig.46

Make sure that the pointer on the arm point

to 0° on the bevel scale on the arm holder. If

they do not point to 0°, loosen the screw

which secure the pointer and adjust it so that

it will point to 0°.

(2) 45° bevel angle

Fig.47

Adjust the 45° bevel angle only after

performing 0° bevel angle adjustment. To

adjust left 45° bevel angle, loosen the lever

and tilt the blade to the left fully. Make sure

that the pointer on the arm points to 45° on

the bevel scale on the arm holder. If the

pointer does not point to 45°, turn the 45°

bevel angle adjusting bolt on the right side of

the arm holder until the pointer points to 45°.

To adjust the right 5° bevel angle, perform

the same procedure as that described above.

Makita LS0815FL [19/124] Maintenance

Содержание

Похожие устройства