Home
Главная
Icom
Адаптер
UT-111
Инструкция по эксплуатации Страница: 30

Icom UT-111 [30/30] Count on us

Содержание

Icom inc 1
Ut 111 1
Contents 2
Installation 1 2
Introduction 2
Operating modes 2
Operation 3 2
Programming 15 2
Appendix a 25 3
Ut 111 logic board programming 0 3
Introduction 4
Channel bank selection 6
Operation 6
Priority id codes 6
Model ut 111 ltr logic board 7
Priority receive id 7
Selected group id 7
Group scan id 8
Operation 8
Receive only groups id 8
Block decode id 9
Model ut lll ltr logic board 9
Selective call dtmf decoder 9
Operation 10
Radio kill function 10
Dtmf encoder 11
Model ut 111 ltr logic board 11
Transmit ani 11
Busy channel lockout 12
Opera ting modes 12
Originating a dispatch call 12
Receiving a dispatch call 12
Interconnect calls 13
Model ut 111 ltr logic board 13
Figure 3 1 installation into the ic f3 f4 transceiver 14
Installation into the ic f3 f4 series transceivers 14
Installation procedure 14
Alignment procedure 16
Installation procedure 16
Ut 111 mobile logic board jumper selection 16
Model ut 111 ltr logic hoard 17
Figure 1 18
Portable radio programming 18
Programming 18
Radio programming 18
All keys and display assignments arc made using the arrow keys to move the highlight to the desired key function and press enter a list of allowable functions appears note that some lists extend beyond the screen and will scroll to reveal other functions 19
Figure 2 19
Figure 2 represents a typical channel assignment there are several areas in this screen which require special attention in order for the ut 111 logic board to operate the trunking function must be enabled 19
In addition one key must be assigned as the trunking group sw button so that a user can select a group finally one key must be assigned as bank up to allow the user to select the bank 19
In the example the bank 20ch 12ch has been selected to support a 20 channel system this screen represents a configuration which has been tested for proper operation if you enable radio functions other than those shown extensive testing should be done to determine if the function selected is compatible with the ut 111 logic board 19
Memory channel screen figure 2 19
Model ut l ii ltr logic board 19
______________ 1 19
Mobile radio programming 20
Programming 20
Figure 3 21
Model ut 111 ltr logic board 21
Figure 4 22
Programming 22
Figure 5 23
Global features programming figure 5 23
Model ut 111 ltr logic board 23
Ut 111 logic board programming 23
Programming 24
Default settings for cs f3 for vhf radio the default file is f3 stl for uhf radio the default file is f4 stl 25
Default settings for cs f300 for vhf radio the default is f300 for uhf radio the default is f400 25
Figure 6 25
Model ut 111 ltr logic board 25
Note default settings for data polarity and data delay can be entered using the stl files provided with the cloning software select file load and enter to list the available files highlight the desired file and press enter 25
Refer to figure 6 to view an example of the programming described in this section 25
System features programming figure 6 25
Programming 26
Group codes 1 through 10 programming 27
Model ut lll ltr logic board 27
Appendix a 28
Global features 28
Orksheet 28
Programming worksheet 28
Rogrammin 28
Home repeater 1 20 ________________ 29
Mobile logic board 29
Model ut 1i1 smartrun 29
Priority receive id 1 250 29
Receive block decode lower id 1 250 29
Receive block decode upper id 1 250 29
System data 29
___ ___ 29
_________________system 1 area number 0 1 ___________________ 29
Count on us 30
Icom inc 30

Icom UT-111 [30/30] Count on us

Содержание

Похожие устройства