Home
Главная
Skil
Шлифовальная Машина
9475 NA
Инструкция по эксплуатации Страница: 7

Skil 9475 NA Инструкция по эксплуатации онлайн [7/184] 92774

d) Storeidlepowertoolsoutofthereachofchildren

anddonotallowpersonsunfamiliarwiththepower

toolortheseinstructionstooperatethepowertool.

Power tools are dangerous in the hands of untrained

users.

e) Maintainpowertools.Checkformisalignmentor

bindingofmovingparts,breakageofpartsandany

otherconditionthatmayaffectthepowertool’s

operation.Ifdamaged,havethepowertoolrepaired

beforeuse. Many accidents are caused by poorly

maintained power tools.

f) Keepcuttingtoolssharpandclean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Usethepowertool,accessoriesandtoolbitsetc.,in

accordancewiththeseinstructions,takinginto

accounttheworkingconditionsandtheworktobe

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5)SERVICE

a) Haveyourpowertoolservicedbyaqualifiedrepair

personusingonlyidenticalreplacementparts. This

will ensure that the safety of the power tool is maintained.

SAFEtY INStRUCtIONS FOR ANGLE GRINDERS

1)SAFETYINSTRUCTIONSFORALLOPERATIONS

a) Thispowertoolisintendedtofunctionasagrinder,

sander,wirebrush,polisherorcut-offtool.Readall

safetywarnings,instructions,illustrationsand

specificationsprovidedwiththispowertool.Failure

to follow all instructions listed below may result in electric

shock, re and/or serious injury.

b) Donotuseaccessorieswhicharenotspecifically

designedandrecommendedbythetool

manufacturer.Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

c) Theratedspeedoftheaccessorymustbeatleast

equaltothemaximumspeedmarkedonthepower

tool.Accessories running faster than their rated speed

can y apart.

d) Theoutsidediameterandthethicknessofyour

accessorymustbewithinthecapacityratingofyour

powertool.Incorrectly sized accessories cannot be

adequately guarded or controlled.

e) Threadedmountingofaccessoriesmustmatchthe

grinderspindlethread.Foraccessoriesmountedby

flanges,thearbourholeoftheaccessorymustfit

thelocatingdiameteroftheflange. Accessories that

do not match the mounting hardware of the power tool

will run out of balance, vibrate excessively and may

cause loss of control.

f) Donotuseadamagedaccessory.Beforeeachuse

inspecttheaccessorysuchasabrasivewheelsfor

chipsandcracks,backingpadsforcracks,tearor

excesswear,wirebrushesforlooseorcracked

wires.Ifthepowertooloraccessoryisdropped,

inspectfordamageorinstallanundamaged

accessory.Afterinspectingandinstallingan

accessory,positionyourselfandbystandersaway

fromtheplaneoftherotatingaccessoryandrunthe

powertoolatmaximumnoloadspeedforone

minute.Damaged accessories will normally break apart

during this test time.

g) Wearpersonalprotectiveequipment 4. Depending

onapplication,usefaceshield,safetygogglesor

safetyglasses.Asappropriate,weardustmask,

hearingprotectors,glovesandshopaproncapable

ofstoppingsmallabrasiveorworkpiecefragments.

The eye protection must be capable of stopping ying

debris generated by various operations. The dust mask or

respirator must be capable of ltrating particles

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

h) Keepbystandersasafedistanceawayfromwork

area.Anyoneenteringtheworkareamustwear

personalprotectiveequipment.Fragments of the

workpiece or of a broken accessory may y away and

cause injury beyond the immediate area of operation.

i) Holdpowertoolbyinsulatedgrippingsurfacesonly,

whenperforminganoperationwherethecutting

accessorymaycontacthiddenwiringoritsown

cord. A cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

j) Positionthecordclearofthespinningaccessory.If

you lose control, the cord may be cut or snagged and

your hand or arm may be pulled into the spinning

accessory.

k) Neverlaythepowertooldownuntiltheaccessory

hascometoacompletestop.The spinning accessory

may grab the surface and pull the power tool out of your

control.

l) Donotrunthepowertoolwhilecarryingitatyour

side.Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

m) Regularlycleanthepowertool’sairvents.The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

n) Donotoperatethepowertoolnearflammable

materials.Sparks could ignite these materials.

o) Donotuseaccessoriesthatrequireliquidcoolants.

Using water or other liquid coolants may result in

electrocution or shock.

2)KICKBACKANDRELATEDWARNINGS

• Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other

accessory. Pinching or snagging causes rapid stalling of

the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the

binding.

• For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on the direction of the wheel’s movement at

the point of pinching. Abrasive wheels may also break

under these conditions.

Содержание

Похожие устройства

d Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these Instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tool accessories and tool bits etc In accordance with these Instructions taking Into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained minute Damaged accessories will normally break apart during this test time g Wear personal protective equipment i Depending on application use face shield safety goggles or safety glasses As appropriate wear dust mask hearing protectors gloves and shop apron capable of stopping small abrasive or workpiece fragments The eye protection must be capable of stopping flying debris generated by various operations The dust mask or respirator must be capable of filtrating particles generated by your operation Prolonged exposure to high intensity noise may cause hearing loss h Keep bystanders a safe distance away from work area Anyone entering the work area must wear personal protective equipment Fragments of the workpiece or of a broken accessory may fly away and cause injury beyond the immediate area of operation i Hold power tool by insulated gripping surfaces only when performing an operation where the cutting accessory may contact hidden wiring or Its own cord A cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock j Position the cord clear of the spinning accessory If you lose control the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory k Never lay the power tool down until the accessory has come to a complete stop The spinning accessory may grab the surface and pull the power tool out of your control I Do not run the power tool while carrying It at your side Accidental contact with the spinning accessory could snag your clothing pulling the accessory into your body mjRegularly clean the power tool s airvents The motor s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards n Do not operate the power tool near flammable materials Sparks could ignite these materials o Do not use accessories that require liquid coolants Using water or other liquid coolants may result in electrocution or shock 2 KICKBACK AND RELATED WARNINGS Kickback is a sudden reaction to a pinched or snagged rotating wheel backing pad brush or any other accessory Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory s rotation at the point of the binding For example if an abrasive wheel is snagged or pinched by the workpiece the edge of the wheel that is entering into the pinch point can dig into the surface of the material causin g the wh eel to climb out or ki ck out The wheel may either jump toward or away from the operator depending on the direction of the wheel s movement at the point of pinching Abrasive wheels may also break under these conditions SAFETY INSTRUCTIONS FOR ANGLE GRINDERS 1 SAFETY INSTRUCTIONS FOR ALL OPERATIONS a This power tool is intended to function as a grinder sander wire brush polisher or cut off tool Read all safety warnings Instructions Illustrations and specifications provided with this power tool Failure to follow all instructions listed below may result in electric shock fire and or serious injury b Do not use accessories which are not specifically designed and recommended by the tool manufacturer Just because the accessory can be attached to your power tool it does not assure safe operation c The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool Accessories running faster than their rated speed can fly apart d The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool Incorrectly sized accessories cannot be adequately guarded or controlled e Threaded mounting of accessories must match the grinder spindle thread For accessories mounted by flanges the arbour hole of the accessory must fit the locating diameter of the flange Accessories that do not match the mounting hardware of the power tool will run out of balance vibrate excessively and may cause loss of control f Do not use a damaged accessory Before each use inspect the accessory such as abrasive wheels for chips and cracks backing pads for cracks tear or excess wear wire brushes for loose or cracked wires If the power tool or accessory is dropped inspect for damage or install an undamaged accessory After Inspecting and installing an accessory position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one 7

Скачать