Bosch GKS 55 GCE [15/213] Product description and specifica
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bosch GKS 55 GCE [15/213] Product description and specifica

Bosch GKS 55 GCE [15/213] Product description and specifica
English | 15
Bosch Power Tools 2 609 932 800 | (8.4.11)
f Blade depth and bevel adjusting locking levers must be
tight and secure before making cut. If blade adjustment
shifts while cutting, it may cause binding and kickback.
f Use extra caution when sawing into existing walls or
other blind areas. The protruding blade may cut objects
that can cause kickback.
Lower guard function
f Check lower guard for proper closing before each use.
Do not operate the saw if lower guard does not move
freely and close instantly. Never clamp or tie the lower
guard into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the lower guard
with the retracting handle and make sure it moves freely
and does not touch the blade or any other part, in all angles
and depths of cut.
f Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a
build-up of debris.
f Lower guard may be retracted manually only for spe-
cial cuts such as “plunge cuts” and “compound cuts”.
Raise lower guard by retracting handle and as soon as
blade enters the material, the lower guard must be re-
leased. For all other sawing, the lower guard should oper-
ate automatically.
f Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An un-
protected, coasting blade will cause the saw to walk back-
wards, cutting whatever is in its path. Be aware of the time
it takes for the blade to stop after switch is released.
Additional safety warnings
f Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
f Do not work overhead with the saw. In this manner you
do not have sufficient control over the power tool.
f Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
f Do not operate the power tool stationary. It is not de-
signed for operation with a saw table.
f Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
f Do not saw ferrous metals. Red hot chips can ignite the
dust extraction.
f When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
f Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
f Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
GKS 55:
The machine is intended for lengthways and crossways cut-
ting of wood with straight cutting lines as well as mitre cuts in
wood while resting firmly on the workpiece. With suitable saw
blades, thin-walled non-ferrous metals, e. g., profiles, can al-
so be sawed.
Working ferrous metals is not permitted.
GKS 55 GCE:
The machine is intended for lengthways and crossways cut-
ting of wood with straight cutting lines as well as mitre cuts in
wood while resting firmly on the workpiece. With suitable saw
blades, thin-walled non-ferrous metals, e. g., profiles, light
uilding materials and plastic can also be sawed.
Working ferrous metals is not permitted.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Lock-off button for On/Off switch
3 Thumbwheel for speed preselection (GKS 55 GCE)
4 Auxiliary handle (insulated gripping surface)
5 Spindle lock button
6 Scale for mitre angle
7 Wing bolt for parallel guide
8 Wing bolt for bevel-angle preselection
9 Cutting mark, 0°
10 Cutting mark, 45°
11 Allen key
12 Parallel guide*
13 Retracting blade guard
OBJ_BUCH-244-004.book Page 15 Friday, April 8, 2011 10:03 AM

Содержание

Похожие устройства

OBJ BUCH 244 004 book Page 15 Friday April 8 2011 10 03 AM English I 15 Bia de dept ha nd bevel adjusting locking levers must be tight and secure before making cut If blade adjustment shifts while cutting it may cause binding and kickback Use extra caution when sawing into existing walls or other blind areas The protruding blade may cut objects that can cause kickback Products sold in GB only Your product is fitted with a BS1363 A approved electric plug with internal fuse ASTA approved to BS1362 If the plug is notsuitable for your socket outlets it should be cutoff and an appropriate plug fitted in its placeby an author ised customer service agent The replacement plug should have the same fuse rating as the original plug Lower guard function The severed plug must be disposed of to avoid a possible Check lower guard for proper closing before each use Do not operate the saw if lower guard does not move shock hazard and should never be inserted intoa mains sock et elsewhere freely and close instantly Never clamp ortiethelower Products sold in AUS and NZ only Use a residual current de guard into the open position If saw is accidentally dropped lower guard may be bent Raise the lower guard vice RCD wi th a rated resi dual current of 30 mA or I ess with the retracting handle and make sure it moves freely and does not touch the blade or any other part in all angles and depths of cut Product Description and Specifica tions Checkthe operation of thelower guard spring If the guard and the spring are not operating properly they Rea d a II sa fety wa mings a nd a II instruc tions Failure to follow the warnings and in structions may result in electric shock fire must be sen iced before use Lower guard may operate sluggishly due to damaged parts gummy deposits or a and or serious injury build up of debris Lower guard may be retracted manually only for spe cial cuts such as plunge cuts and compound cuts Ra ise lower gua rd by retra ding ha ndle and a s soon a s While reading the operating instructions unfold the graphics page for the machi ne and I eave it open blade entersthematerial the lower guard must be re Intended Use leased For all other sawing the lower guard should oper ate automatically GKS55 Always observe thatthelower guard iscoveringthe blade before placing saw down on bench or floor An un protected coasting blade will cause the saw to walk back wards cutting whatever is in its path Beaware of the time it takes for the blade tostop after switch is released The machine is intended for lengthways and crossways cut ting of wood with straight cutting lines as well as mitre cuts in wood whileresting firmly on theworkpiece Withsui tablesaw blades thin walled non ferrous metals e g profiles can al so be sawed Working ferrous metals is not permitted Additional safety warnings Do not reach into the saw dust ej ector with your hands They could be injured by rotating parts Do not work overhead withthe saw In this manner you do not have sufficient control over the power tool Use suitable detedors to determine if utility lines are hidden in the work area or call the local utility company GKS55GCE The machine is intended for lengthways and crossways cut ting of wood with straight cutting lines as well as mitre cuts in wood whileresting firmly on theworkpiece Withsui tablesaw blades thin walled non ferrous metals e g profiles light uilding materials and plastic can also be sawed Working ferrous metals is not permitted for assistance Contact with electric lines can lead to fire and electricshock Damaging a gas line can lead to explo Product Features sion Penetrating a water line causes property damage or may cause an electric shock The numbering of the product features refers to the illustra tion of the machine on the graphics page Do not operate the power tool stationary It is not de signed for operation with a saw table Do not use high speed steel HSS saw blades Such saw bladescan easily break Do not sawferrousmetals Red hot chips can ignite the dust extraction When working with the machine always hold it firmly with both hands and provide for a secure stance The power tool is guided moresecurewith both hands 1 On Off switch 2 Lock offbuttonforOn Offswitch 3 Thumbwheel for speed preselection GKS 55 GCE 4 Auxiliary handle insulated gripping surface 5 Spindle lock button 6 Scale for mitre angle 7 Wing bolt for parallel guide 8 Wing bolt for bevel angle preselection 9 Cutting mark 0 Secure the workpiece A workpiece clamped with clamp ing devices or in a vice is held more secure than by hand 10 Cutting mark 45 Always wait until the machine has come to a complete 11 Allen key stop before placing it down The tool insert can jam and 12 Parallel guide I ead to I oss of control over the power tool 13 Retracting bladeguard Bosch Power Tools 2609 932 8001 8 4 11

Скачать