![Autel AutoLink AL539B [15/92] Navigation characters](/img/pdf.png)
Autel AutoLink AL539B [15/92] Navigation characters
13
2) CD -- Includes user‟s manual, MaxiLink update software, and
etc.
3) OBD2 cable -- Provides power to tool and communicates
between tool and vehicle.
4) USB cable -- Used to upgrade the scan tool, and to print
retrieved data.
5) 3.7V Li-ion battery -- Provides power when disconnected with
vehicle.
6) Probes -- Contacts the circuit or component to be tested.
AutoLink
AL539 Only:
7) Protective Nylon Case – Contains the main unit and cables
while not in use.
AutoLink
AL539B Only:
8) Battery test cable -- Used to contact the terminals of vehicle
battery.
9) Carry case -- A nylon case to store the scan tool when not in use.
3.4 Navigation Characters
Characters used to help navigate the scan tool are:
1) ―$‖ -- Identifies the control module number from which data is
retrieved. Indicates the Test ID in On-Board Mon. Test.
2) ―G‖ -- Indicates graphic viewing is available.
3.5 Keyboard
No solvents such as alcohol are allowed to clean the keypad or display.
Use a mild nonabrasive detergent and a soft cotton cloth. Do not soak
the keypad as the keypad is not waterproof.
3.6 Power and charge
Power on
Содержание
- Table of contents 1
- Safety precautions and warnings 3
- Diagnostic trouble codes dtcs 4
- General information 4
- On board diagnostics obd ii 4
- Location of the data link connector dlc 5
- Obd ii readiness monitors 6
- Obd ii monitor readiness status 7
- Obd ii definitions 8
- Obd ii modes of operation 9
- Tool description 12
- Using the scan tool 12
- Accessories included 14
- Specifications 14
- Keyboard 15
- Navigation characters 15
- Power and charge 15
- Power on 15
- Auto power off 16
- Li ion battery charging 16
- Dtc lookup 18
- System setup 19
- Language setup 20
- To enter the setup menu 20
- Configure monitors 21
- Spark ign required monitors 21
- Compression ign required monitors 22
- Key beep set 23
- Unit of measure 23
- Status beep set 24
- Tool self test 25
- Tool information 27
- Update mode 27
- Product troubleshooting 29
- Vehicle coverage 29
- Vehicle linking error 29
- Led lamps not working 30
- Operating error 30
- Scan tool doesn t power up 30
- Review data 31
- Obdii diagnostics 32
- Reading codes 34
- Erasing codes 36
- Live data 38
- Viewing data 38
- Recording data 42
- Current test will be stored in a temporary cache 44
- Figure 5 1 44
- Figure 5 2 44
- Figure 5 3 44
- If data from previously tested vehicle is not erased data from 44
- If you select a location marked with an asterisk icon a 44
- Message prompting to overwrite old recording displays 44
- Previous recording in the memory location 44
- The asterisk icon on the screen indicates that there is a 44
- Use the up down scroll button to select a memory location and press the ok button 44
- Playback data 48
- Figure 5 0 49
- Figure 5 8 49
- Figure 5 9 49
- If there is no recording in selected location a message not 49
- Supported or stored no data displays on the screen 49
- Use the left right button to view pids of next or previous frames 49
- Use the up down button to view recorded pids of each frame 49
- Viewing freeze frame data 49
- Retrieving i m readiness status 51
- A retrieve i m readiness status with one click i m 52
- Readiness key 52
- B retrieve i m readiness status in typical way 54
- O2 monitor test 57
- Figure 5 7 58
- Figure 5 8 58
- Figure 5 9 58
- If the vehicle does not support the mode an advisory message 58
- Use the up down scroll button to view more screens of data if additional information is available in more than one page 58
- View test results of selected o2 sensor 58
- Will be displayed on the screen 58
- On board monitor test 59
- Figure 5 2 61
- Figure 5 3 61
- Figure 5 4 61
- For can equipped vehicles test selections can be as below 61
- Use the up down scroll button to select the desired monitor from on board mon test menu and press the ok button 61
- View test data on screen 61
- Component test 62
- Viewing vehicle information 64
- Modules present 65
- General information 67
- Ready test 67
- Ready test application 67
- As post repair diagnostic tool 68
- As pre check diagnostic tool 69
- Led and tone interpretation 70
- Audio tone interpretation 71
- Led interpretation 71
- Circuit test function 72
- Dc voltage 72
- Ac voltage 73
- Continuity 73
- Diodes 74
- Current 75
- Pretest 77
- Start test 77
- Starter test 77
- Starter test procedure 78
- Charging system test 81
- Charging system test procedure 82
- Battery test only for al539b 86
- Test procedure 86
- Print data 90
- Limited one year warranty 92
- Service procedures 92
- Warranty and service 92
Похожие устройства
- Autel MaxiTPMS TS401 Руководство пользователя
- Autel MaxiCheck PRO Руководство пользователя
- Autel MaxiCheck Oil Light/Service Reset Руководство пользователя
- Autel MaxiCheck EPB Руководство пользователя
- Autel Maxivideo MV201 8.5 мм Руководство пользователя
- Autel Maxivideo MV400 5.5 мм Руководство пользователя
- Autel Maxivideo MV400 8.5 мм Руководство пользователя
- Coolfort CF-1216 Инструкция по эксплуатации
- Coolfort СF-1221 Инструкция по эксплуатации
- Coolfort CF-0525GY Инструкция по эксплуатации
- Cremesso Compact Automatic Burgundy Red Инструкция по эксплуатации
- Cremesso LM 600 Инструкция по эксплуатации
- Cuckoo CMC-CHSS1004F Инструкция по эксплуатации
- Defender Optimum MS-125 Nano Инструкция по эксплуатации
- Defender Game Racer Turbo GT Инструкция по эксплуатации
- Delonghi VVX 1885 Stirella Инструкция по эксплуатации
- Delonghi CTI 2103.BZ Инструкция по эксплуатации
- Delonghi CTI 2103.CP Инструкция по эксплуатации
- Delonghi CTI 2103.W Инструкция по эксплуатации
- Delonghi CTI 2103.BK Инструкция по эксплуатации