![Autel AutoLink AL539B [16/92] Auto power off](/img/pdf.png)
Autel AutoLink AL539B [16/92] Auto power off
14
Before using the scan tool, you must provide power to it. There are
five methods for providing power to the scan tool.
Cable connection to vehicle.
AC/DC external power adapter.
Li-ion battery.
USB port.
Battery test cable.
During vehicle testing, power for the scan tool is usually provided
through the vehicle cable connection. The detailed instructions show
as below:
1) Connect the OBD II Cable to scan tool.
2) Find DLC on vehicle.
A plastic DLC cover may be found for some vehicles and you
need to remove it before plugging the OBD2 cable.
3) Plug OBD II cable to the vehicle‟s DLC.
When the scan tool is not connected to a vehicle, it can be powered
in the other three ways.
Auto power-off
Solely powered up by Li-ion battery, the tool will automatically turn
off after 15 minutes of inactivity.
Li-ion battery charging
You can charge your Li-ion battery by connecting it to an external
power adapter, by connecting it to the vehicle‟s DLC or by
connecting it to a USB port on your computer. The tool displays a
battery icon in the upper-right corner of the screen to show
approximately how much charge is left.
Using a Power Adapter
If you're using an external power adapter, connect the tool to the
adapter. Then plug the adapter into a working electrical socket.
Содержание
- Table of contents 1
- Safety precautions and warnings 3
- Diagnostic trouble codes dtcs 4
- General information 4
- On board diagnostics obd ii 4
- Location of the data link connector dlc 5
- Obd ii readiness monitors 6
- Obd ii monitor readiness status 7
- Obd ii definitions 8
- Obd ii modes of operation 9
- Tool description 12
- Using the scan tool 12
- Accessories included 14
- Specifications 14
- Keyboard 15
- Navigation characters 15
- Power and charge 15
- Power on 15
- Auto power off 16
- Li ion battery charging 16
- Dtc lookup 18
- System setup 19
- Language setup 20
- To enter the setup menu 20
- Configure monitors 21
- Spark ign required monitors 21
- Compression ign required monitors 22
- Key beep set 23
- Unit of measure 23
- Status beep set 24
- Tool self test 25
- Tool information 27
- Update mode 27
- Product troubleshooting 29
- Vehicle coverage 29
- Vehicle linking error 29
- Led lamps not working 30
- Operating error 30
- Scan tool doesn t power up 30
- Review data 31
- Obdii diagnostics 32
- Reading codes 34
- Erasing codes 36
- Live data 38
- Viewing data 38
- Recording data 42
- Current test will be stored in a temporary cache 44
- Figure 5 1 44
- Figure 5 2 44
- Figure 5 3 44
- If data from previously tested vehicle is not erased data from 44
- If you select a location marked with an asterisk icon a 44
- Message prompting to overwrite old recording displays 44
- Previous recording in the memory location 44
- The asterisk icon on the screen indicates that there is a 44
- Use the up down scroll button to select a memory location and press the ok button 44
- Playback data 48
- Figure 5 0 49
- Figure 5 8 49
- Figure 5 9 49
- If there is no recording in selected location a message not 49
- Supported or stored no data displays on the screen 49
- Use the left right button to view pids of next or previous frames 49
- Use the up down button to view recorded pids of each frame 49
- Viewing freeze frame data 49
- Retrieving i m readiness status 51
- A retrieve i m readiness status with one click i m 52
- Readiness key 52
- B retrieve i m readiness status in typical way 54
- O2 monitor test 57
- Figure 5 7 58
- Figure 5 8 58
- Figure 5 9 58
- If the vehicle does not support the mode an advisory message 58
- Use the up down scroll button to view more screens of data if additional information is available in more than one page 58
- View test results of selected o2 sensor 58
- Will be displayed on the screen 58
- On board monitor test 59
- Figure 5 2 61
- Figure 5 3 61
- Figure 5 4 61
- For can equipped vehicles test selections can be as below 61
- Use the up down scroll button to select the desired monitor from on board mon test menu and press the ok button 61
- View test data on screen 61
- Component test 62
- Viewing vehicle information 64
- Modules present 65
- General information 67
- Ready test 67
- Ready test application 67
- As post repair diagnostic tool 68
- As pre check diagnostic tool 69
- Led and tone interpretation 70
- Audio tone interpretation 71
- Led interpretation 71
- Circuit test function 72
- Dc voltage 72
- Ac voltage 73
- Continuity 73
- Diodes 74
- Current 75
- Pretest 77
- Start test 77
- Starter test 77
- Starter test procedure 78
- Charging system test 81
- Charging system test procedure 82
- Battery test only for al539b 86
- Test procedure 86
- Print data 90
- Limited one year warranty 92
- Service procedures 92
- Warranty and service 92
Похожие устройства
- Autel MaxiTPMS TS401 Руководство пользователя
- Autel MaxiCheck PRO Руководство пользователя
- Autel MaxiCheck Oil Light/Service Reset Руководство пользователя
- Autel MaxiCheck EPB Руководство пользователя
- Autel Maxivideo MV201 8.5 мм Руководство пользователя
- Autel Maxivideo MV400 5.5 мм Руководство пользователя
- Autel Maxivideo MV400 8.5 мм Руководство пользователя
- Coolfort CF-1216 Инструкция по эксплуатации
- Coolfort СF-1221 Инструкция по эксплуатации
- Coolfort CF-0525GY Инструкция по эксплуатации
- Cremesso Compact Automatic Burgundy Red Инструкция по эксплуатации
- Cremesso LM 600 Инструкция по эксплуатации
- Cuckoo CMC-CHSS1004F Инструкция по эксплуатации
- Defender Optimum MS-125 Nano Инструкция по эксплуатации
- Defender Game Racer Turbo GT Инструкция по эксплуатации
- Delonghi VVX 1885 Stirella Инструкция по эксплуатации
- Delonghi CTI 2103.BZ Инструкция по эксплуатации
- Delonghi CTI 2103.CP Инструкция по эксплуатации
- Delonghi CTI 2103.W Инструкция по эксплуатации
- Delonghi CTI 2103.BK Инструкция по эксплуатации