Home
Главная
Metabo
Водяной Насос
P 4000 S
Инструкция по эксплуатации Страница: 13

Metabo P 4000 S [13/62] Installing the hydromat hwa only

ENGLISH

"Technical Specifications"). Com-

pletely unroll cable reels.

 Do not buckle, squeeze, drag or

drive over power cable and exten-

sion cables; protect from sharp

dges.

 Pl

ace extension cable so that it can

not get into the fluid to be pumped.

 Unplug:

 p

rior to all servicing;

 w

hen persons are in the swim-

ming pool or garden pond.



Danger by pump failures!

 If

you notice transport damage while

unpacking, notify your supplier

immediately. Do not operate the

pump!

 Be

fore each use check the pump,

especially the power cable and plug

for possible damage. Risk of fatal

electric shock!

 A da

maged pump must be work-

manlike repaired before it can be

sed again.

 D

o not attempt to repair the pump

yourself! Only trained specialists are

permitted to service or repair pumps

or pressure vessels.

Caution!

To avoid water damage, e.g.

flooded rooms, caused by pump mal-

functions or defects:

 provide for suitable safety measures

such as the following:

 alarm or

 collection tank with monitoring.

The manufacturer is not liable for any

mage caused by:

 improper use of the pump;

 overloading of the pump through

ntinous operation;

 failure to operate and store the

ump in a frost-free environment;

 unauthorised modification of the

ump (repairs to electrical equip-

ment may only be carried out by

ualified electricians!);

 use of spare parts which have not

een tested and approved by the

manufacturer; or

 use of unsuitable installation materi-

als (fittings, connection lines etc.).

Suitable installation materials:

 pressure-resistant

(min. 10 bar)

 heat-resistant (min. 100°C).

The pump is easily assembled and con-

nected. 

If in doubt, contact your specialist sup-

plier or a qualified electrician.

5.1 Installing the Hydromat 

(HWA only)

Note: 

Before initial operation the Hydro-

mat must be installed (illustration

according to version).

1. Check to see that the pump is

turned off and the power cord plug

(18) is unplugged.

2. Turn adaptor (16) onto the dis-

charge port of the pump.

3. Place Hydromat (17) on the adaptor

and secure with the union nut.

4. Adjust Hydromat position so that the

ntrol panel is easily accessible.

5. Plug power cord plug of pump (18)

in the Hydromat's cable socket (19).

5.2 Installation

 The pump must be placed on a

plane and level surface, suitable of

bearing the weight of the pump fully

filled with water.

 To avoid

vibrations the pump should

be placed on an elastic base.

 The

installation location should be

well vented and protected from

atmospheric exposure.

 When operated at garden ponds

and pools the pump must be set up

safe against flooding and safe-

garded against falling into the water.

y additional legal requirements

are to be observed.

5.3 Connecting the Suction

Line

Note:

Possibly further accessories may

required for connection (see "Availa-

ble Accessories").

Caution!

The suction line needs to be

insta

lled in such manner that it does

not exert mechanical force or distor-

tion to the pump.

Caution!

When pumping contaminated

flu

ids install a suction strainer to pro-

tect the pump from sand and dirt.

Note: 

A check valve is recommended to

prevent water backflow when the pump

is turned off.

 All screw fittings must be sealed

with thread sealing tape; leaks

cause the priming of air, which

reduces or completely prevents the

priming of water.

 Th

e suction line should have an

inner diameter of 1" (25 mm) mini-

mum and must be kink, pressure,

and vacuum

resistent.

 Ke

ep suction line as short as practi-

cal, as with increasing length the

ump capacity is reduced.

 The

suction line should ascend

towards the pump to prevent air

locks.

 A sufficient water supply must be

ensured, the foot valve at the end of

the suction line must be submerged

in water at all times.

5.4 Discharge Port

Note:

Possibly further accessories may

required for connection (see "Availa-

ble Accessories").

Caution!

The discharge (or pressure)

lin

e needs to be installed in such

manner that it does not exert mechan-

ical force or distortion to

the pump.

 Al

l screw fittings should be sealed

with thread sealing tape to prevent

leakage.

 All parts of the pressure line must be

resistant to internal pressure.

 All

parts of the pressure line must be

installed in a workmanlike manner.

Danger!

Improper installation and use

parts not resistant to internal pres-

sure can cause the pressure line to

eak during operation. Risk of per-

sonal injury by liquid spurting from

the

line under high pressure!

5. Prior to Operation

1819

Metabo P 4000 S [13/62] Installing the hydromat hwa only

Содержание

Похожие устройства