Husqvarna 553RS (9667800-02) [44/788] Fitting the blade guard and saw blade
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Husqvarna 553RS (9667800-02) [44/788] Fitting the blade guard and saw blade

Husqvarna 553RS (9667800-02) [44/788] Fitting the blade guard and saw blade
ASSEMBLY
44 – English
Fitting the trimmer guard and trimmer
head
• Fit the correct trimmer guard (A) for use with the
trimmer head. CAUTION! Ensure that the guard
extension is fitted.
• Hook the trimmer guard/combination guard onto the
fitting on the shaft and secure with the bolt (L).
• Fit the drive disc (B) on the output shaft.
• Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
• Insert the locking pin (C) in the hole to lock the shaft.
• Screw on the trimmer head/plastic blades (H)
anticlockwise.
• To dismantle, follow the instructions in the reverse
order.
Fitting the blade guard and saw blade
• Remove the mounting plate (H). Fit the adapter (I) and
bracket (J) with the two screws (K) as shown. Fit the
blade guard (A) to the adapter using the 4 screws (L)
as shown.
CAUTION! Use the recommended blade guard. See the
Technical data section.
• Fit the drive disc (B) on the output shaft.
• Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
• Insert the locking pin (C) in the hole to lock the shaft.
• Place the blade (D) and support flange (F) on the
output shaft.
• Fit the nut (G). Tighten the nut to a torque of 35-50 Nm
(3.5-5 kpm). Use the socket spanner in the tool kit.
Grasp the handle of the spanner as close to the
trimmer guard as possible. To tighten the nut, turn the
spanner in the opposite direction to the direction of
rotation (Caution! left-hand thread).
• When loosening and tightening the saw blade nut,
there is a risk of injury from the teeth of the saw blade.
You should therefore always ensure that your hand is
shielded by the blade guard when doing this. Always
use a socket spanner with a shaft that is long enough
to allow this. The arrow in the diagram shows the area
B
A
M
L
H
A
L
C
M
H
H
A
L
I
J
K
H
F
D
B
C
G
1-H1158941-01,533-553RS west.fm Page 44 Tuesday, July 11, 2017 2:29 PM

Содержание

Похожие устройства

Fitting the trimmer guard and trimmer head blade guard A to the adapter using the 4 screws L as shown CAUTION Use the recommended blade guard See the Technical data section Fit the correct trimmer guard A for use with the trimmer head CAUTION Ensure that the guard extension is fitted Hook the trimmer guard combination guard onto the fitting on the shaft and secure with the bolt L Fit the drive disc B on the output shaft Fit the drive disc B on the output shaft Turn the output shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing Turn the output shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing Insert the locking pin C in the hole to lock the shaft Screw on the trimmer head plastic blades H anticlockwise H Insert the locking pin C in the hole to lock the shaft Place the blade D and support flange F on the output shaft Fit the nut G Tig hten the nut to a torque of 3 5 50 Nm 3 5 5 kpm Use the socket spanner in the tool kit Grasp the handle of the spanner as close to the trimmer guard as possible To tighten the nut turn the spanner in the opposite direction to the direction of rotation Caution left hand thread To dismantle follow the instructions in the reverse order Fitting the blade guard and saw blade When loosening and tightening the saw blade nut there Isa risk of injury from the teeth of the saw blade You should therefore always ensure that your hand is shielded by the blade guard when doing this Always use a socket spanner with a shaft that is long enough to allow this The arrow in the diagram shows the area Remove the mounting plate H Fit the adapter I and bracket J with the two screws K as shown Fit the 44 English

Скачать