Skil 0730 RA [8/112] Environment
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil 0730 RA [8/112] Environment

Skil 0730 RA [8/112] Environment
8
- after replacing the spool system test-run the tool for at
least one minute without load to ensure that the tool is
operating properly
mAINTENANCE / SERVICE
• This tool is not intended for professional use
• Alwaysdisconnectplugfrompowersourcebefore
cleaningand/ormaintenance
• Always keep tool and cord clean (especially the
ventilation slots)
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- clean line cutting blade J 2 and cutting guard A 2
after each use
- clean ventilation slots L 2 regularly with a brush or
compressed air
• Regularly check the condition of the cutting head and the
tightness of nuts, bolts and screws
• Regularly check for worn or damaged components and
have them repaired/replaced when necessary
• Storage (
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail M on the wall with 4
screws (notsupplied) and horizontally leveled
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBlESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switchoffthetoolanddisconnecttheplugbefore
investigatingtheproblem
★ Tool does not operate
- power supply socket faulty -> use another socket
- extension cord damaged -> replace extension cord
★ Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/o switch defective -> contact dealer/service
station
★ Tool vibrates abnormally
- grass too high -> cut in stages
★ Tool does not cut
- line too short/broken o -> feed the line manually
★ Line cannot be fed
- spool empty -> replace spool
- line entangled inside spool -> inspect spool; rewind if
necessary
★ Line is not cut o to correct length -> remove cover from
cutting blade
★ Line keeps breaking
- line entangled inside spool -> inspect spool; rewind if
necessary
- trimmer incorrectly used -> only trim with the tip of the
line; avoid stones, walls and other hard objects; feed
the line regularly
ENVIRONmENT
• Donotdisposeofelectrictools,accessoriesand
packagingtogetherwithhouseholdwastematerial
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
DEClARATION OF CONFORmITY
• We declare under our sole responsibility that the product
described under “Technical data” is in conformity with the
following standards or standardization documents: EN
60335, EN 61000, EN 55014 in accordance with the
provisions of the directives 2006/95/EC, 2004/108/EC,
2006/42/EC, 2000/14/EC, 2011/65/EU
• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
¹ÊÁÂÆιÆ¼½ÊÇǾ¼½Æ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
Ĺ¾ÁÂÿʹ¹¾
ÈÈÊÇιÄ¹Æ¹¿½Ê
19.12.2013
10
NOISE/VIBRATION
• Measured in accordance with EN 60335 the sound
pressure level of this tool is 70 dB(A) and the sound
power level 90 dB(A) (standard deviation: 3 dB), and the
vibration <2.5 m/s² (hand-arm method; uncertainty K =
1.5 m/s²)
• Measured in accordance with 2000/14/EC (EN/ISO
3744) the guaranteed sound power level LWA is lower
than 93 dB(A) (conformity assessment procedure
according to Annex VI)
Notied body : KEMA, Arnhem, NL
Notied body identication number : 0344
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60335; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level

Содержание

Похожие устройства

after replacing the spool system test run the tool for at least one minute without load to ensure that the tool is operating properly trimmer incorrectly used only trim with the tip of the line avoid stones walls and other hard objects feed the line regularly MAINTENANCE SERVICE ENVIRONMENT This tool is not intended for professional use Always disconnect plug from power source before cleaning and or maintenance Always keep tool and cord clean especially the ventilation slots clean the tool with a damp cloth do not use cleaning agents or solvents clean line cutting blade J and cutting guard A after each use clean ventilation slots L regularly with a brush or compressed air Regularly check the condition of the cutting head and the tightness of nuts bolts and screws Regularly check for worn or damaged components and have them repaired replaced when necessary Storage store the tool Indoors in a dry and locked up place out of reach of children securely mount storage rail M on the wall with 4 screws not supplied and horizontally leveled If the tool should fail despite the care taken in manufacturing and testing procedures repair should be carried out by an after sales service centre for SKIL power tools send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station addresses as well as the service diagram of the tool are listed on www skil com Do not dispose of electric tools accessories and packaging together with household waste material only for EU countries in observance of European Directive 2012 19 EC on waste of electric and electronic equipment and its implementation in accordance with national law electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility symbol will remind you of this when the need for disposing occurs DECLARATION OF CONFORMITY C We declare under our sole responsibility that the product described under Technical data is in conformity with the following standards or standardization documents EN 60335 EN 61000 EN 55014 in accordance with the provisions of the directives 2006 95 EC 2004 108 EC 2006 42 EC 2000 14 EC 2011 65 EU Technical file at SKIL Europe BV PT SEU ENG1 4825 BD Breda NL Marijn van der Hoofden Operations Engineering Olaf Dijkgraaf Approval Manager SKIL Europe BV 4825 BD Breda NL TROUBLESHOOTING The following listing shows problem symptoms possible causes and corrective actions if these do not identify and correct the problem contact your dealer or service station I switch off the tool and disconnect the plug before Investigating the problem Tool does not operate power supply socket faulty use another socket extension cord damaged replace extension cord Tool operates intermittently internal wiring defective contact dealer service station on off switch defective contact dealer service station Tool vibrates abnormally grass too high cut in stages Tool does not cut line too short broken off feed the line manually Line cannot be fed spool empty replace spool line entangled inside spool inspect spool rewind if necessary Line is not cut off to correct length rem we cover from cutting blade Line keeps breaking line entangled inside spool inspect spool rewind if necessary 19 12 2013 C 10 NOISE VIBRATION Measured in accordance with EN 60335 the sound pressure level of this tool is 70 dB A and the sound power level 90 dB A standard deviation 3dB and the vibration 2 5 m s2 hand arm method uncertainty К 1 5 m s2 Measured in accordance with 2000 14 EC EN ISO 3744 the guaranteed sound power level LWA is lower than 93 dB A conformity assessment procedure according to Annex VI Notified body KEMA Arnhem NL Notified body identification number 0344 The vibration emission level has been measured in accordance with a standardised test given in EN 60335 it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned using the tool for different applications or with different or poorly maintained accessories may significantly increase the exposure level the times when the tool is switched off or when it is running but not actually doing the job may significantly reduce the exposure level 8

Скачать
Случайные обсуждения

Ответы 0

Нужна пружина для катушки с леской
3 года назад

Ответы 1

Как заправить леску
2 года назад