Home
Главная
Alpina
Газонокосилка
A 460 WSE
Инструкция по эксплуатации Страница: 26

Alpina A 460 WSE [26/92] Standards of use

STANDARDS OF USE

NOTE - The number which precedes each paragraph links the

references in the text to the respective figures (listed on the pa-

ges 2 - 3).

NOTE - The machine can be supplied with some of the

components already fitted.

WARNING - Unpacking and completing the assembly

should be done on a flat and stable surface, with enough

space for machine handling and its packaging, always

making use of suitable equipment.

Disposal of the packaging should be done in accordance

with the local regulations in force.

Complete machine assembly following the indications on the

instruction sheets enclosed with each part to be assembled.

NOTE - The meanings of the symbols on controls are

explained on page 4 and following.

The engine is controlled by a dual action switch to pre-

vent starting it accidentally. To start, press the button (2) and

pull the lever (1). The engine automatically stops when the

lever (1) is released.

The cutting height is adjusted using the levers (1).

The four wheels must be at the same height.

MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE IS

STOPPED.

In power-driven models, draw the lever (1) towards the

handle for forward movement.

The lawnmower stops moving forward when the lever is

released.

NOTE - This machine cuts lawns in various modes; before

starting work, prepare the machine based on how the lawn is

to be mowed.

MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF.

Preparation for grass cutting and collection in

grass-catcher:

– Lift the rear stone-guard (1) and correctly hook on the grass-

catcher (2) as shown in the figure.

Preparation for grass cutting and rear discharge:

– Remove the grass-catcher and check that the rear stone-

guard (1) maintains its lowered position;

Preparation for grass cutting and mulching (if pres-

ent):

– Lift the rear stone-guard (1) and fit the deflector cap (5) in the

outlet, keeping it slightly tilted to the right. Fasten it by fitting

the two pins (6) into the holes provided until the fastener

tooth clicks into place (7).

To remove the deflector cap (5), lift the stone-guard (1) and

press down on the centre until the tooth (7) is released.

Connect the extension cable correctly as indicated.

Start the engine by pressing the safety push-button (2) and

pulling the switchgear lever (1).

While cutting, ensure that the electric cable is always

behind you and on the area of grass already cut.

• In case of “mulching” or rear dumping of grass: always

avoid removing a large quantity of grass. Never cut more

than one third the total grass height in a single passage!

3.3

3.2

3.1c

3.1b

3.1a

3. GRASS CUTTING

2.3

2.2

2.1

2. DESCRIPTION OF CONTROLS

1. FINISH ASSEMBLY

Regulate the forward speed according to the lawn conditions

and the amount of grass removed.

LAWN CARE RECOMENDATIONS

Each type of grass has different features and may thus require

different ways to care for the lawn; always read the instructions

on seed boxes for mowing height for the growth conditions in

the work area.

Keep in mind that most grass is made up of a stem and one or

more leaves. If leaves are fully cut, the lawn is damaged and

growth is more difficult.

The following indications generally apply:

– too low a cut causes grass tears and uprooting, with a “spot-

ted” aspect;

– in the summer, cutting must be higher to avoid the ground

from drying;

– do not cut wet grass; this could reduce blade efficiency due

to sticky grass and tear the lawn;

– for particularly high grass, initially mow at maximum admit-

ted machine height followed by a second mow after two or

three days.

The appearance of the lawn will improve if you alternate the

cutting in both directions at the same height.

When you have finishing mowing, release the lever (1).

FIRST disconnect the cable extension from the supply socket

(2) and THEN from the side of the lawnmower’s switchgear (3).

WAIT FOR THE BLADE TO STOP before carrying out any type

of work on the machine.

IMPORTANT NOTE

Should the motor stop during use through overheating, wait

about 5 minutes before re-starting.

IMPORTANT - Regular, careful maintenance is essential for

keeping the safety level and original performance of the

machine unchanged in time.

Store the lawnmower in a dry place.

1) Wear strong working gloves during any cleaning, mainte-

nance or adjustment operation on the machine.

2) Remove the grass debris after each cut and mud accumu-

lated inside the chassis to avoid their drying and thus mak-

ing the next start-up difficult.

3) Always ensure that ventilation openings are kept clear of

debris.

4) The paintwork on the inside of the chassis may peel off in

time due to the abrasive action of the cut grass; in this case,

intervene promptly by touching up the paintwork using a

rustproof paint to prevent the formation of rust that would

lead to corrosion of the metal.

Each intervention on the blade is best if conducted at a

specialised Centre that has the most appropriate tools.

Only blades with the following codes must be used on this

machine:

81004341/3 (for model 430)

81004346/3 (for model 480)

Blades must always be marked « » or «GGP». Given the

product evolution, the above mentioned blade may be replaced

in time by others, with similar interchangeable and operating

safety characteristics.

Reassemble the blade (2) with the code and markings facing

the ground, following the order indicated in the illustration.

Tighten the central screw (1) using a torque wrench set to 16-

20 Nm.

Do not use forced water and avoid wetting the motor or

the electrical components.

Do not use harsh products for cleaning the chassis.

4.2

4.1

4. ROUTINE MAINTENANCE

3.4

Содержание

Похожие устройства

Regulate the forward speed according to the lawn conditions and the amount of grass removed EN STANDARDS OF USE NOTE The number which precedes each paragraph links the references in the text to the respective figures listed on the pa ges 2 3 I 1 FINISH ASSEMBLY NOTE The machine components already fitted can be supplied with some of on the 2 DESCRIPTION OF CONTROLS NOTE The meanings of explained on page 4 and following the Each type of grass has different features and may thus require different ways to care for the lawn always read the instructions on seed boxes for mowing height for the growth conditions in the work area the WARNING Unpacking and completing the assembly should be done on a flat and stable surface with enough space for machine handling and its packaging always making use of suitable equipment Disposal of the packaging should be done in accordance with the local regulations in force Complete machine assembly following the indications instruction sheets enclosed with each part to be assembled LAWN CARE RECOMENDATIONS Keep in mind that most grass is made up of a stem and one or more leaves If leaves are fully cut the lawn is damaged and growth is more difficult The following indications generally apply too low a cut causes grass tears and uprooting with a spot ted aspect in the summer cutting must be higher to avoid the ground from drying do not cut wet grass this could reduce blade efficiency due to sticky grass and tear the lawn for particularly high grass initially mow at maximum admit ted machine height followed by a second mow after two or three days The appearance of the lawn will improve cutting in both directions at the same height symbols on controls if you alternate the are I 2 1 The engine is controlled by a dual action switch to pre vent starting it accidentally To start press the button 2 and pull the lever 1 The engine automatically stops when the lever 1 is released SE When you have finishing mowing release the lever 1 FIRST disconnect the cable extension from the supply socket 2 and THEN from the side of the lawnmower s switchgear 3 WAIT FOR THE BLADE TO STOP before carrying out any type of work on the machine I 2 2 The cutting height is adjusted using the levers 1 The four wheels must be at the same height MAKE THIS ADJUSTMENT ONLY WHEN THE STOPPED IMPORTANT NOTE Should the motor stop during about 5 minutes before re starting I 2 3 I in power driven models handle for forward movement The lawnmower stops moving released BLADE IS draw the lever 1 towards the forward when the lever is NOTE This machine cuts lawns in various modes before starting work prepare the machine based on how the lawn is to be mowed MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF 13 1 a Preparation for grass cutting and collection in grass catcher Lift the rear stone guard 1 and correctly hook on the grass catcher 2 as shown in the figure 3 1 b Preparation for grass cutting and rear discharge Remove the grass catcher and check that guard 1 maintains its lowered position 13 1c the rear stone Preparation for grass cutting and mulching if pres ent Lift the rear stone guard 1 and fit the deflector cap 5 in the outlet keeping it slightly tilted to the right Fasten it by fitting the two pins 6 into the holes provided until the fastener tooth clicks into place 7 To remove the deflector cap 5 lift the stone guard 1 and press down on the centre until the tooth 7 is released I 3 3 I while cutting ensure that the electric behind you and on the area of grass already cut 24 overheating wait maintenance is essential original performance of for the 1 Wear strong working gloves during any cleaning mainte nance or adjustment operation on the machine Remove the grass debris after each cut and mud accumu lated inside the chassis to avoid their drying and thus mak ing the next start up difficult 3 Always ensure that ventilation openings are kept clear of debris 4 The paintwork on the inside of the chassis may peel off in time due to the abrasive action of the cut grass in this case intervene promptly by touching up the paintwork using a rustproof paint to prevent the formation of rust that would lead to corrosion of the metal 2 I 3 2 Connect the extension cable correctly as indicated Start the engine by pressing the safety push button 2 and pulling the switchgear lever 1 through I 4 ROUTINE MAINTENANCE IMPORTANT Regular careful keeping the safety level and machine unchanged in time Store the lawnmower in a dry place I 3 GRASS CUTTING use cable is always In case of mulching or rear dumping of grass always avoid removing a large quantity of grass Never cut more than one third the total grass height in a single passage 4 1 Each intervention on the blade is best if conducted at a specialised Centre that has the most appropriate tools Only blades with the following codes must be used on this machine 81004341 3 for model 430 81004346 3 for model 480 Blades must always be marked A or GGP Given the product evolution the above mentioned blade may be replaced in time by others with similar interchangeable and operating safety characteristics Reassemble the blade 2 with the code and markings facing the ground following the order indicated in the illustration Tighten the central screw 1 using a torque wrench set to 1620 Nm I 4 2 Do not use forced water and avoid wetting the motor or the electrical components Do not use harsh products for cleaning the chassis

Скачать