![D-Link des-1228/me/b1 [138/413] Des 1228 me 5](/img/pdf.png)
D-Link des-1228/me/b1 [138/413] Des 1228 me 5
![D-Link des-1228/me/b1 [138/413] Des 1228 me 5](/views2/1166101/page138/bg8a.png)
DES-1228/ME Metro Ethernet Managed Switch CLI Reference Guide
134
config bandwidth_control
Purpose
Used to configure bandwidth control on a port by-port basis.
Syntax
config bandwidth_control [<portlist>] {rx_rate [no_limit | <value 64-
1024000>] | tx_rate [no_limit <value 64-1024000>]} (1)
Description
This command is used to configure bandwidth on a port by-port basis.
Note: DES-1228/ME Ver. B1, the granularity is 62.5 kbps on all
ranges.
Parameters
<portlist> − Specifies a port or range of ports to be configured.
rx_rate − Specifies that one of the parameters below (no_limit or
<value 64-1024000>) will be applied to the rate at which the above
specified ports will be allowed to receive packets
no_limit − Specifies that there will be no limit on the rate of packets
received by the above specified ports.
<value 64-1024000> − Specifies the traffic limit, in Kbits, that the
above ports will be allowed to receive.
tx_rate − Specifies that one of the parameters below (no_limit or
<value 64-1024000>) will be applied to the rate at which the above
specified ports will be allowed to transmit packets.
no_limit − Specifies that there will be no limit on the rate of packets
received by the above specified ports.
<value 64-1024000> − Specifies the traffic limit, in Kbits, that the
above ports will be allowed to receive.
Actual rate = |rate entered/ minimum granularity|* minimal granularity,
for example: 62.5=|100/62.5|*62.5”
|number| implies the closest smaller integer.
Restrictions
Only Administrator level, Operator level or Power User level users can
issue this command.
Example usage:
To configure bandwidth control:
DES-1228/ME:5#config bandwidth_control 1 rx_rate 64
Command: config bandwidth_control 1 rx_rate 64
Note: To perform precise bandwidth control, it is required to enable the
flow
control to mitigate the retransmission of TCP traffic.
The specified RX rate is not a multiple of 62.5, thus the closest
smaller multiple 62.5 is chosen.
Success.
DES-1228/ME:5#
Содержание
- Able of 3
- Ontents 3
- Accessing the switch via the serial port 5
- Introduction 5
- Ntroduction 5
- Setting the switch s ip address 5
- Connecting to the switch 7
- Onsole 7
- Sing the 7
- Using the console cli 7
- Des 1228 me metro ethernet managed switch cli reference guide 8
- Figure 2 2 the command 8
- Figure 2 3 example command parameter help 8
- When users enter a command without its required parameters the cli will prompt users with next possible completions message 8
- With the message next possible completions every command in the cli has this feature and complex commands have several layers of parameter prompting in addition after typing any given command plus one space users can see all of the next possible sub commands in sequential order by repeatedly pressing the tab key to re enter the previous command at the command prompt press the up arrow cursor key the previous command will appear at the command prompt 8
- Des 1228 me metro ethernet managed switch cli reference guide 9
- Figure 2 4 using the up arrow to re enter a command 9
- Figure 2 5 the next available commands prompt 9
- Indicate a numerical value or character string braces indicate optional parameters or a choice of parameters and brackets indicate required parameters if a command is entered that is unrecognized by the cli the top level commands will be displayed under the available commands prompt 9
- The top level commands consist of commands such as show or config most of these commands require one or more parameters to narrow the top level command this is equivalent to show what or config what where the what is the next parameter for example if users enter the show command with no additional parameters the cli will then display all of the possible next parameters 9
- Des 1228 me metro ethernet managed switch cli reference guide 10
- Figure 2 6 next possible completions show command 10
- In the above example all of the possible next parameters for the show command are displayed at the next command prompt the up arrow was used to re enter the show command followed by the account parameter the cli then displays the user accounts configured on the switch 10
- Command syntax 11
- Ommand 11
- Square brackets 11
- Vertical bar 11
- Braces 12
- Line editing key usage 12
- Parentheses 12
- Multiple page display control keys 13
- Basic switch commands 14
- Command parameters 14
- Ommands 14
- Command parameters 15
- Disable password encryption 15
- Enable password encryption 15
- Des 1228 me metro ethernet managed switch cli reference guide 16
- Create account 17
- Config account 18
- Delete account 19
- Show account 19
- Show session 20
- Des 1228 me metro ethernet managed switch cli reference guide 21
- Description this command is used to display information about the switch 21
- Example usage to display the switch s information 21
- Parameters none 21
- Purpose used to display general information about the switch 21
- Restrictions none 21
- Show switch 21
- Syntax show switch 21
- Show serial_port 22
- Config serial_port 23
- Disable clipaging 24
- Enable clipaging 24
- Disable telnet 25
- Enable telnet 25
- Telnet 26
- Disable web 27
- Enable web 27
- Reboot 29
- Logout 31
- Show config 32
- Config terminal_line 33
- Disable jumbo_frame 34
- Enable jumbo_frame 34
- Show terminal_line 34
- Show jumbo_frame 35
- Config configuration config_id 36
- Config configuration trap 37
- Show config information 37
- Anner and 38
- Command parameters 38
- Config command prompt 38
- Modify banner and prompt commands 38
- Ommands 38
- Config greeting _message 39
- Show greeting_message 40
- Command parameters 41
- Ommands 41
- Switch port commands 41
- Config ports 42
- Show ports 43
- Des 1228 me metro ethernet managed switch cli reference guide 44
- Example usage to display the configuration of all ports on a standalone switch with description 44
- Command parameters 45
- Ecurity 45
- Ommands 45
- Port security commands 45
- Config port_security ports 46
- Delete port_security_entry 47
- Clear port_security_entry 48
- Show port_security 49
- Disable port_security trap_log 50
- Enable port_security trap_log 50
- Anagement 51
- Etwork 51
- Network management snmp commands 51
- Ommands 51
- Command parameters 52
- Command parameters 53
- Create snmp user 53
- Create snmp user 54
- Delete snmp user 54
- Show snmp user 55
- Create snmp view 56
- Delete snmp view 57
- Show snmp view 57
- Create snmp community 58
- Delete snmp community 59
- Show snmp community 59
- Config snmp engineid 60
- Show snmp engineid 61
- Create snmp group 62
- Delete snmp group 63
- Show snmp groups 63
- Des 1228 me metro ethernet managed switch cli reference guide 64
- Example usage to display the currently configured snmp groups on the switch 64
- Create snmp host 65
- Delete snmp host 66
- Show snmp host 66
- Create trusted_host 67
- Delete trusted_host 67
- Show trusted_host 68
- Enable snmp authenticate_traps 69
- Enable snmp traps 69
- Enable snmp linkchange_traps 70
- Disable snmp authenticate_traps 71
- Disable snmp linkchange_traps 71
- Disable snmp traps 71
- Config snmp linkchange_traps ports 72
- Show snmp traps 72
- Des 1228 me metro ethernet managed switch cli reference guide 73
- Config snmp system_contact 74
- Config snmp system_location 74
- Config snmp system_name 75
- Disable rmon 75
- Enable rmon 75
- Config snmp coldstart_traps 76
- Config snmp warmstart_traps 76
- Command parameters 77
- Ommands 77
- Switch utility commands 77
- Tility 77
- Download 78
- Config firmware 79
- Des 1228 me metro ethernet managed switch cli reference guide 80
- Show firmware information 81
- Upload 82
- Des 1228 me 5 83
- Des 1228 me metro ethernet managed switch cli reference guide 83
- Enable autoconfig 84
- Des 1228 me metro ethernet managed switch cli reference guide 85
- Note with autoconfig enabled the switch ipif settings now define the switch as a dhcp client use the show switch command to display the new ip settings status 85
- The very end of the autoconfig process appears like this 85
- Config autoconfig timeout 86
- Disable autoconfig 86
- Show autoconfig 87
- Des 1228 me metro ethernet managed switch cli reference guide 89
- Example usage to ping the ipv6 address fe80 254 85ff fe32 1804 six times 89
- Restrictions none 89
- Traceroute 90
- Config terminal line 91
- Show terminal line 91
- Command parameters 92
- Etwork 92
- Network monitoring commands 92
- Ommands 92
- Onitoring 92
- Show packet ports 93
- Show error ports 94
- Show utilization 95
- Des 1228 me metro ethernet managed switch cli reference guide 96
- To display the current flash memory utilization 96
- To display the port utilization statistics 96
- Clear counters 97
- Clear log 97
- Enable syslog 98
- Show log 98
- Disable syslog 99
- Show syslog 99
- Create syslog host 100
- Create syslog host 101
- Config syslog 102
- Delete syslog host 104
- Show syslog host 105
- Config log_save_timing 106
- Show log_save_timing 106
- Disable command logging 107
- Enable command logging 107
- Show command logging 107
- Multiple spanning tree protocol mstp commands 109
- Ommands 109
- Panning 109
- Rotocol 109
- Ultiple 109
- Disable stp 111
- Enable stp 111
- Config stp version 112
- Config stp 113
- Config stp ports 114
- Create stp instance_id 115
- Config stp instance_id 116
- Config stp priority 117
- Delete stp instance_id 117
- Config stp mst_config_id 118
- Config stp mst_ports 119
- Show stp 120
- Des 1228 me metro ethernet managed switch cli reference guide 121
- Status 2 stp enabled for rstp 121
- Status 3 stp enabled for mstp 121
- Show stp ports 122
- Show stp instance 123
- Config stp trap 124
- Show stp mst_config_id 124
- Atabase 125
- Command parameters 125
- Forwarding database commands 125
- Ommands 125
- Orwarding 125
- Create fdb 126
- Create multicast_fdb 126
- Config fdb aging_time 127
- Config multicast_fdb 127
- Delete fdb 128
- Clear fdb 129
- Show multicast_fdb 129
- Show fdb 130
- Config multicast port_filtering_mode 131
- Show multicast port_filtering_mode 132
- Command parameters 133
- Ommands 133
- Ontrol 133
- Packet storm control commands 133
- Config traffic control 134
- Show traffic control 135
- Config traffic control_trap 136
- Command parameters 137
- Ommands 137
- Qos commands 137
- Config bandwidth_control 138
- Des 1228 me 5 138
- Show bandwidth_control 139
- Config scheduling 140
- Config scheduling_mechanism 141
- Show scheduling 141
- Show scheduling_mechanism 142
- Config 802 p user_priority 143
- Show 802 p user_priority 144
- Config 802 p default_priority 145
- Show 802 p default_priority 146
- Config cos mapping 147
- Des 1228 me metro ethernet managed switch cli reference guide 148
- Description this command is used to display information regarding cos mapping enabled ports and their mapping method 148
- Example usage to show the cos mapping information 148
- Purpose used to show cos mapping 148
- Restrictions none 148
- Show cos mapping 148
- Specifies a range of ports to be displayed if no parameter is specified the all ports priority settings will be shown 148
- Config cos tos value 149
- Show cos tos 149
- Config dscp_mapping 150
- Des 1228 me metro ethernet managed switch cli reference guide 151
- Description this command displays the information for dscp mapping to traffic class 151
- Example usage to show the dscp map to traffic class 151
- Purpose used to show dscp value map to traffic class 151
- Restrictions none 151
- Show dscp_mapping 151
- The dscp value of the incoming packet if no parameter is specified all the dscp value mapping to traffic class will be shown 151
- Command parameters 152
- Config mirror port 152
- Irroring 152
- Ommands 152
- Port mirroring commands 152
- Disable mirror 153
- Enable mirror 153
- Show mirror 154
- Command parameters 155
- Create vlan 155
- Ommands 155
- Vlan commands 155
- Config vlan 156
- Delete vlan 156
- Create vlan vlanid 157
- Delete vlan vlanid 157
- Config vlan vlanid 158
- Disable pvid auto_assign 159
- Enable pvid auto_assign 159
- Show pvid auto_assign 159
- Config gvrp 160
- Disable gvrp 161
- Enable gvrp 161
- Show vlan 162
- Show gvrp 163
- Command parameters 164
- Create link_aggregation 164
- Ggregation 164
- Link aggregation commands 164
- Ommands 164
- Config link_aggregation 165
- Delete link_aggregation group_id 165
- Config link_aggregation algorithm 166
- Show link_aggregation 166
- Config lacp_ports 167
- Show lacp_ports 168
- Basic ip commands 169
- Command parameters 169
- Ommands 169
- Config ipif 170
- Show ipif 171
- Des 1228 me metro ethernet managed switch cli reference guide 172
- Example usage to display ip interface settings 172
- Disable autoconfig 173
- Enable autoconfig 173
- Delete ipif 174
- Enable ipif_ipv6_link_local_auto 174
- Disable ipif_ipv6_link_local_auto 175
- Show ipif_ipv6_link_local_auto 175
- Command parameters 176
- Igmp snooping commands 176
- Nooping 176
- Ommands 176
- Config igmp_snooping 177
- Config igmp_snooping querier 178
- Config router_ports 179
- Config router_ports_forbidden 180
- Enable igmp_snooping 180
- Disable igmp_snooping 181
- Show igmp_snooping 181
- Show router_ports 182
- Show igmp_snooping group 183
- Config igmp_snooping data_driven_learning 184
- Config igmp_snooping data_driven_learning max_learned_entry 184
- Clear igmp_snooping data_driven_group 185
- Show igmp_snooping host 185
- Config igmp access_authentication ports 186
- Show igmp_snooping host 186
- Show igmp access_authentication ports 187
- Show igmp_snooping forwarding 187
- Des 1228 me metro ethernet managed switch cli reference guide 188
- Example usage example usage to show all igmp snooping forwarding entries located on the switch 188
- Command parameters 189
- Config dhcp_relay 189
- Dhcp relay commands 189
- Ommands 189
- Config dhcp_relay add ipif 190
- Config dhcp_relay delete ipif 190
- Config dhcp_relay option_82 check 191
- Config dhcp_relay option_82 state 191
- Config dhcp_relay option_82 policy 192
- Config dhcp_relay option_82 remote id 193
- Show dhcp_relay 193
- Enable dhcp_relay 194
- Disable dhcp_relay 195
- Command parameters 196
- Ommands 196
- X commands 196
- Disable 802 x 197
- Enable 802 x 197
- Show 802 x 198
- Des 1228 me metro ethernet managed switch cli reference guide 199
- Example usage example usage to display the 802 x authentication states 199
- To display the 802 x authentication state for port based 802 x 199
- Config 802 x auth_mode 200
- Config 802 x capability ports 201
- Config 802 x auth_parameter ports 202
- Config 802 x auth_protocol 203
- Config 802 x init 203
- Config 802 x reauth 204
- Config radius add 205
- Config radius delete 205
- Config radius 206
- Config radius parameter 207
- Show radius 207
- Create 802 x guest_vlan 208
- Config 802 x guest_vlan ports 209
- Show 802 x guest_vlan 209
- Delete 802 x guest_vlan 210
- Des 1228 me metro ethernet managed switch cli reference guide 211
- Description this command is used to display the current radius accounting client currently configured on the switch 211
- Example usage to view the current radius accounting client 211
- Parameters none 211
- Purpose used to display the current radius accounting client 211
- Restrictions none 211
- Show acct_client 211
- Syntax show acct_client 211
- Des 1228 me metro ethernet managed switch cli reference guide 212
- Description this command is used to display the current radius authentication client currently configured on the switch 212
- Example usage to view the current radius authentication client 212
- Parameters none 212
- Purpose used to display the current radius authentication client 212
- Restrictions none 212
- Show auth_client 212
- Syntax show auth_client 212
- Des 1228 me metro ethernet managed switch cli reference guide 213
- Description this command is used to display the current authentication diagnostics of the switch on a per port basis 213
- Example usage to display the current authentication diagnostics for port 1 213
- Purpose used to display the current authentication diagnostics 213
- Restrictions none 213
- Show auth_diagnostics 213
- Specifies a range of ports 213
- Show auth_session_statistics 214
- Show auth_statistics 214
- A username of up to 15 alphanumeric characters in length 215
- Create 802 x user 215
- Des 1228 me metro ethernet managed switch cli reference guide 215
- Description this command is used to create new 802 x users 215
- Example usage example usage to create an 802 x user 215
- Example usage to display the current authentication statistics for port 1 215
- Purpose used to create a new 802 x user 215
- Restrictions only administrator level operator level or power user level users can issue this command 215
- Delete 802 x user 216
- Show 802 x user 216
- Access control list acl commands 217
- Command parameters 217
- Ommands 217
- Ontrol 217
- Command parameters 218
- Create access_profile 218
- Create access_profile 219
- Config access_profile 220
- Create access_profile 220
- Delete access_profile 220
- Config access_profile 221
- Config access_profile 222
- Config access_profile 223
- Show access_profile 223
- Create cpu access_profile 224
- Create cpu access_profile 225
- Delete cpu access_profile 225
- Config cpu access_profile 226
- Delete cpu access_profile 226
- Config cpu access_profile 227
- Config cpu access_profile 228
- Delete cpu access_profile 229
- Show cpu access_profile 229
- Des 1228 me metro ethernet managed switch cli reference guide 230
- Description this command is used in conjunction with the disable cpu_interface_filtering command below to enable and disable cpu interface filtering on the switch 230
- Enable cpu_interface_filtering 230
- Example usage example usage to show the cpu filtering state on the switch 230
- Parameters none 230
- Purpose used to enable cpu interface filtering on the switch 230
- Restrictions only administrator level operator level or power user level users can issue this command 230
- Syntax enable cpu_interface_filtering 230
- Disable cpu_interface_filtering 231
- Config cpu_filter l3_control_pkt 232
- Cpu filtering commands 232
- Iltering 232
- Ommands 232
- Show cpu_filter l3_control_pkt 232
- Des 1228 me metro ethernet managed switch cli reference guide 233
- Example usage example usage to display the l3 control packet filtering status for port 1 and 2 233
- Afeguard 234
- Command parameters 234
- Ommands 234
- Safeguard engine commands 234
- Config safeguard_engine 235
- Show safeguard_engine 235
- Des 1228 me metro ethernet managed switch cli reference guide 236
- Example usage example usage to display the safeguard engine status 236
- Command parameters 237
- Config traffic_segmentation 237
- Egmentation 237
- Ommands 237
- Raffic 237
- Traffic segmentation commands 237
- Des 1228 me metro ethernet managed switch cli reference guide 238
- Description this command is used to display the current traffic segmentation configuration on the switch 238
- Example usage example usage to display the current traffic segmentation configuration on the switch 238
- Purpose used to display the current traffic segmentation configuration on the switch 238
- Restrictions the port lists for segmentation and the forward list must be on the same switch there are no user level restrictions 238
- Show traffic_segmentation 238
- Specifies a port or range of ports for which the current traffic segmentation configuration on the switch will be displayed 238
- Command parameters 239
- Config sntp 239
- Ime and 239
- Ommands 239
- Time and sntp commands 239
- Enable sntp 240
- Show sntp 240
- Config time 241
- Disable sntp 241
- Config dst 242
- Config time_zone 242
- Config dst 243
- Show time 244
- Arp commands 245
- Command parameters 245
- Config arpentry 245
- Create arpentry 245
- Ommands 245
- Config arp_aging time 246
- Config arpentry 246
- Delete arpentry 246
- Show arpentry 247
- Clear arptable 248
- Command parameters 249
- Create iproute 249
- Ommands 249
- Outing 249
- Routing table commands 249
- Delete iproute 250
- Show iproute 250
- Create ipv6route 251
- Delete ipv6route 251
- Show ipv6route 252
- Command parameters 253
- Disable mac_notification 253
- Enable mac_notification 253
- Mac notification commands 253
- Ommands 253
- Otification 253
- Config mac_notification 254
- Config mac_notification ports 254
- Show mac_notification 255
- Show mac_notification ports 255
- Des 1228 me metro ethernet managed switch cli reference guide 256
- Example usage example usage to display all port s mac address table notification status settings 256
- Access authentication control commands 257
- Ommands 257
- Ontrol 257
- Uthentication 257
- Command parameters 258
- Disable authen_policy 259
- Enable authen_policy 259
- Create authen_login method_list_name 260
- Show authen_policy 260
- Config authen_login 261
- Config authen_login 262
- Delete authen_login method_list_name 262
- Show authen_login 263
- Config authen_enable 264
- Create authen_enable method_list_name 264
- Config authen_enable 265
- Config authen_enable 266
- Delete authen_enable method_list_name 266
- Show authen_enable 267
- Config authen application 268
- Show authen application 268
- Des 1228 me metro ethernet managed switch cli reference guide 269
- Example usage to display the login and enable method list for all applications on the switch 269
- Create authen server_host 270
- Des 1228 me metro ethernet managed switch cli reference guide 271
- Example usage example usage to create a tacacs authentication server host with port number 1234 a timeout value of 10 seconds and a retransmit count of 5 271
- Config authen server_host 272
- Delete authen server_host 273
- Create authen server_group 274
- Show authen server_host 274
- Config authen server_group 275
- Delete authen server_group 276
- Show authen server_group 276
- Config authen parameter response_timeout 277
- Config authen parameter attempt 278
- Show authen parameter 278
- Config admin local_enable 279
- Enable admin 279
- Des 1228 me 5 280
- Des 1228 me metro ethernet managed switch cli reference guide 280
- Example usage example usage to configure the password for the local_enable authentication method in plain text 280
- To configure the password for the local_enable authentication method in encrypted form 280
- Command parameters 281
- Enable ssh 281
- Ommands 281
- Ssh commands 281
- Config ssh authmode 282
- Disable ssh 282
- Show ssh authmode 283
- Config ssh server 284
- Show ssh server 284
- Config ssh user 285
- Show ssh user authmode 286
- Config ssh algorithm 287
- Des 1228 me metro ethernet managed switch cli reference guide 288
- Description this command will display the current ssh algorithm setting status 288
- Parameters none 288
- Purpose used to display the ssh algorithm setting 288
- Restrictions none 288
- Show ssh algorithm 288
- Syntax show ssh algorithm 288
- Usage example to display ssh algorithms currently set on the switch 288
- Ommands 289
- Smtp commands 289
- Command parameters 290
- Disable smtp 290
- Enable smtp 290
- Config smtp 291
- Show smtp 292
- Smtp send_testmsg 292
- Des 1228 me metro ethernet managed switch cli reference guide 293
- Example usage example usage to send a test mail message to all configured mail recipients 293
- Cable diagnostics commands 294
- Cable_diag ports 294
- Command parameters 294
- Iagnostics 294
- Ommands 294
- Des 1228 me metro ethernet managed switch cli reference guide 295
- Example usage example usage to test the cable on ports 25 to 28 295
- Command parameters 296
- Config dhcp_local_relay vlan 296
- Dhcp local relay commands 296
- Ommands 296
- Config dhcp_local_relay option_82 ports 297
- Config dhcp_local_relay option_82 remote_id 297
- Disable dhcp_local_relay 298
- Enable dhcp_local_relay 298
- Show dhcp_local_relay 298
- Show dhcp_local_relay option_82 ports 299
- Command parameters 300
- Config gratuitous_arp send ipif_status_up 300
- Gratuitous arp commands 300
- Ommands 300
- Ratuitous 300
- Config gratuitous_arp learning 301
- Config gratuitous_arp send dup_ip_detected 301
- Config gratuitous_arp_send periodically 302
- Enable gratuitous_arp 302
- Disable gratuitous_arp 303
- Show gratuitous_arp 303
- Des 1228 me metro ethernet managed switch cli reference guide 304
- Example usage example usage to display gratuitous arp log and trap states 304
- Command parameters 305
- Disable vlan_trunk 305
- Enable vlan_trunk 305
- Ommands 305
- Runking 305
- Vlan trunking commands 305
- Config vlan_trunk 306
- Des 1228 me metro ethernet managed switch cli reference guide 307
- To configure a vlan trunk port if port 6 7 have the same vlan configurations before enable vlan trunking port 6 is la 1 member port port 7 is la 1 master port 307
- To configure a vlan trunk port if port 6 is la 1 member port port 7 is la 1 master port 307
- Show vlan_trunk 308
- Asymmetric vlan commands 309
- Command parameters 309
- Disable asymmetric_vlan 309
- Enable asymmetric_vlan 309
- Ommands 309
- Symmetric 309
- Show asymmetric_vlan 310
- Command parameters 311
- Create igmp_snooping multicast_vlan 311
- Igmp snooping multicast vlan commands 311
- Nooping 311
- Ommands 311
- Ulticast 311
- Config igmp_snooping multicast_vlan 312
- Config igmp_snooping multicast_vlan 313
- Config igmp_snooping multicast_vlan multicast_group 313
- Delete igmp_snooping multicast_vlan 314
- Show igmp_snooping multicast_vlan_group 314
- Disable igmp_snooping multicast_vlan 315
- Enable igmp_snooping multicast_vlan 315
- Show igmp_snooping multicast_vlan 315
- Des 1228 me metro ethernet managed switch cli reference guide 316
- Example usage example usage to display igmp snooping multicast vlan information 316
- Command parameters 317
- Lldp commands 317
- Ommands 317
- Disable lldp 318
- Enable lldp 318
- Config lldp message_tx_hold_multiplier 319
- Config lldp message_tx_interval 319
- Config lldp reinit_delay 320
- Config lldp tx_delay 320
- Config lldp notification_interval 321
- Config lldp ports notification 321
- Config lldp ports admin_status 322
- Config lldp ports mgt_addr 322
- Config lldp ports basic_tvls 323
- Config lldp ports dot1_tlv_pvid 324
- Config lldp ports dot1_tlv_protocol_vid 325
- Config lldp ports dot1_tlv_vlan_name 325
- Config lldp ports dot1_tlv_protocol_identity 326
- Config lldp ports dot1_tlv_vlan_name 326
- Config lldp ports dot3_tlvs 327
- Config lldp forward_message 328
- Show lldp 328
- Show lldp mgt_addr 329
- Show lldp ports 329
- Show lldp local_ports 330
- Des 1228 me metro ethernet managed switch cli reference guide 331
- Example usage example usage to display outbound lldp advertisements for individual ports in detail 331
- To display outbound lldp advertisements for specific ports in normal mode 331
- Show lldp remote_ports 332
- Des 1228 me metro ethernet managed switch cli reference guide 333
- Example usage example usage to display remote table entries in brief mode 333
- Des 1228 me metro ethernet managed switch cli reference guide 334
- To display remote table entries in detailed mode 334
- To display remote table entries in normal mode 334
- Des 1228 me metro ethernet managed switch cli reference guide 335
- Show lldp statistics 336
- Show lldp statistics ports 336
- Des 1228 me metro ethernet managed switch cli reference guide 337
- Example usage example usage to display statistics information of port 1 337
- To display statistics information of port 1 337
- Command parameters 338
- Dos prevention commands 338
- Ommands 338
- Revention 338
- Config dos_prevention dos_type 339
- Disable dos_prevention trap_log 340
- Enable dos_prevention trap_log 340
- Show dos_prevention 341
- Clear dos_prevention counters 342
- Command parameters 344
- Inding 344
- Ip mac 344
- Ip mac port binding commands 344
- Ommands 344
- Config address_binding ip_mac ipaddress 345
- Create address_binding ip_mac ipaddress 345
- Config address_binding ip_mac ports 346
- Show address_binding 347
- Des 1228 me 5 show address_binding ports command show address_binding ports enabled ports 1 allow zeroip ports 1 des 1228 me 5 348
- Des 1228 me metro ethernet managed switch cli reference guide 348
- To display address binding entries on the switch to display address binding entries on the switch 348
- To display blocked address binding on the switch 348
- To display enabled ports address binding on the switch 348
- Delete address_binding 349
- Disable address_binding trap_log 350
- Enable address_binding trap_log 350
- Command parameters 351
- Etection 351
- Loopback detection commands 351
- Ommands 351
- Oopback 351
- Config loopdetect 352
- Config loopdetect ports 353
- Disable loopdetect 354
- Enable loopdetect 354
- Show loopdetect 355
- Show loopdetect ports 356
- Config loopdetect trap 357
- Command parameters 358
- Flow meter commands 358
- Ommands 358
- Config flow_meter profile_id 359
- Show flow_meter 360
- Arp spoofing prevention commands 361
- Command parameters 361
- Ommands 361
- Poofing 361
- Revention 361
- Config arp_spoofing_prevention 362
- Show arp_spoofing_prevention 363
- Command parameters 364
- Echnical 364
- Ommands 364
- Show tech_support 364
- Technical support commands 364
- Upport 364
- Des 1228 me metro ethernet managed switch cli reference guide 365
- Upload tech_support_totftp 366
- Command history commands 367
- Command parameters 367
- Istory 367
- Ommand 367
- Ommands 367
- Des 1228 me metro ethernet managed switch cli reference guide 368
- Example usage example usage to display all of the commands in the cli 368
- To display the parameters for a specific command 368
- Des 1228 me metro ethernet managed switch cli reference guide 369
- Description this command is used to display all of the commands available through the command line interface cli 369
- Example usage to display all commands 369
- Parameters none 369
- Purpose used to display all commands in the command line interface cli 369
- Restrictions none 369
- Syntax dir 369
- Config command_history 370
- Show command_history 370
- Bpdu attack protection commands 371
- Command parameters 371
- Ommands 371
- Rotection 371
- Config bpdu_protection ports 372
- Config bpdu_protection recovery_timer 373
- Config bpdu_protection 374
- Enable bpdu_protection 375
- Disable bpdu_protection 376
- Show bpdu_protection 376
- Des 1228 me metro ethernet managed switch cli reference guide 377
- Example usage example usage to display bpdu protection settings for ports 377
- Command parameters 378
- Config pppoe circuit_id_insertion state 378
- Ircuit 378
- Nsertion 378
- Ommands 378
- Pppoe circuit id insertion commands 378
- Config pppoe circuit_id_insertion ports 379
- Show pppoe circuit_id_insertion 379
- Show pppoe circuit_id_insertion ports 380
- Command parameters 381
- Config filter dhcp_server 381
- Creening 381
- Dhcp server screening settings 381
- Ettings 381
- Des 1228 me metro ethernet managed switch cli reference guide 382
- Description this command is used to display dhcp server client filter list created on the switch 382
- Example usage example usage to add an entry from the dhcp server client filter list in the switch s database 382
- Example usage example usage to display the dhcp server filter list created on the switch 382
- Parameters none 382
- Purpose used to display current dhcp server client filter list created on the switch 382
- Restrictions none 382
- Show filter dhcp_server 382
- Syntax show filter dhcp_server 382
- To configure the dhcp filter state 382
- Config filter dhcp_server illegal_server_log_suppress_duration 383
- Config filter dhcp_server trap log 383
- Create ipv6 neighbor_cache ipif 384
- Delete ipv6 neighbor_cache ipif 384
- Eighbour 384
- Ipv6 neighbour discovery commands 384
- Iscovery 384
- Ommands 384
- Delete ipv6 neighbor_cache ipif 385
- Show ipv6 neighbor_cache ipif 385
- Config ipv6 nd ns ipif 386
- Show ipv6 nd 386
- Debug error_log 388
- Debug software commands 388
- Oftware 388
- Ommands 388
- Des 1228 me metro ethernet managed switch cli reference guide 389
- Des 1228 me metro ethernet managed switch cli reference guide 390
- Des 1228 me metro ethernet managed switch cli reference guide 391
- Des 1228 me metro ethernet managed switch cli reference guide 392
- Des 1228 me metro ethernet managed switch cli reference guide 393
- Des 1228 me metro ethernet managed switch cli reference guide 394
- Des 1228 me metro ethernet managed switch cli reference guide 395
- Des 1228 me metro ethernet managed switch cli reference guide 396
- Debug config error_reboot 397
- Des 1228 me metro ethernet managed switch cli reference guide 397
- Purpose this command is used to set if the switch needs to be rebooted when a fatal error occurs when the error occurs the watchdog timer will be disabled by the system first and then all debug information will be saved in nvram if the error_reboot is enabled the watchdog shall be enabled after all information is stored into nvram 397
- Syntax debug config error_reboot enable disable 397
- Debug config error_reboot 398
- Debug show error_reboot state 398
- Bpdu tunnel commands 399
- Command parameters 399
- Config bpdu_tunnel ports 399
- Ommands 399
- Show bpdu_tunnel 399
- Disable bpdu_tunnel 400
- Enable bpdu_tunnel 400
- Assword 402
- Des 1228 me metro ethernet managed switch cli reference guide 402
- Ecovery 402
- Ppendix 402
- Rocedure 402
- Des 1228 me metro ethernet managed switch cli reference guide 403
- Ntries 403
- Ppendix 403
- Des 1228 me metro ethernet managed switch cli reference guide 404
- Des 1228 me metro ethernet managed switch cli reference guide 405
- Des 1228 me metro ethernet managed switch cli reference guide 406
- Des 1228 me metro ethernet managed switch cli reference guide 407
- Des 1228 me metro ethernet managed switch cli reference guide 408
- Des 1228 me metro ethernet managed switch cli reference guide 409
- Des 1228 me b1 trap list 410
- Des 1228 me metro ethernet managed switch cli reference guide 410
- Ntries 410
- Ppendix 410
- Proprietary trap list 410
- Des 1228 me metro ethernet managed switch cli reference guide 411
- D radius 412
- Ppendix 412
- Ssignment 412
- Ttributes 412
Похожие устройства
- D-Link dph-150s/f4 Инструкция по эксплуатации
- D-Link dir-615/k/k2a Инструкция по эксплуатации
- D-Link dir-615/fb/o1a Инструкция по эксплуатации
- D-Link dir-651/a/a Инструкция по эксплуатации
- D-Link dgs-1008d/i2 Инструкция по эксплуатации
- D-Link dir-860l/ru/a1a Инструкция по эксплуатации
- D-Link dir-506l/a2a Инструкция по эксплуатации
- D-Link dir-825/a/d1a Инструкция по эксплуатации
- D-Link dsl-2650u/ra/u1a Инструкция по эксплуатации
- D-Link des-1008d/l2a Инструкция по эксплуатации
- D-Link dap-1155/a1a Инструкция по эксплуатации
- Quattro Elementi Energia 2500 Li Инструкция по эксплуатации
- Quattro Elementi Energia 2701 Li Инструкция по эксплуатации
- Quattro Elementi Energia 3000 Инструкция по эксплуатации
- Quattro Elementi Energia 4000 Инструкция по эксплуатации
- Quattro Elementi Energia 5000 Li Инструкция по эксплуатации
- Quattro Elementi Energia 5001 Li Инструкция по эксплуатации
- Quattro Elementi Power Box 4000 Инструкция по эксплуатации
- Quattro Elementi Power Box 4000 Air Инструкция по эксплуатации
- Quattro Elementi Power Cube 4000 Air Инструкция по эксплуатации
Скачать
Случайные обсуждения