Home
Главная
Hitachi
Перфораторы
DH50MR
Инструкция по эксплуатации Страница: 9

Hitachi DH50MR [9/84] English

English

(1) Center pin

䢇 Applied to core bits from 38 mm to 150 mm

䢇 Applied to core bits 32 mm and 35 mm

NOTE:

Do not use core bits 25 mm or 29 mm.

(2) Core bit

䢇 External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94,

105, 120, 150 mm

(with guide plate, not applicable to cores 25 mm

or 29 mm)

(3) Core bit shank

䢇 Applied to core bits above 38 mm

䢇 Applied to core bits below 35 mm

4. Drilling holes .... For drilling metal and wooden

materials

5. Bolt placing operation with Chemical Anchor

(Rotation + Hammering)

6. Crushing (Hammering)

7. Groove digging and edging (Hammering)

8. Asphalt cutting (Hammering)

9. Scooping Work (Hammering)

10. Surface Roughing (Hammering)

11. Tamping (Hammering)

12. Syringe (for chip removal)

䡬 Hammer grease A

500 g (in a can)

70 g (in a green tube)

30 g (in a green tube)

Optional accessories are subject to change without

notice.

APPLICATIONS

䡬 Drilling holes in concrete

䡬 Drilling anchor holes

䡬 Crushing concrete, chipping, digging, and squaring

(by applying optional accessories)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a power receptacle while

the power switch is in the ON position, the power

tool will start operating immediately, which could

cause a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. How to install tool

NOTE:

For tools such as a bull point and a cold chisel,

use only Hitachi genuine parts.

(1) Clean, then smear the tool shank with the grease

provided in the green tube (Fig. 1).

(2) To attach the tool (SDS max shank), insert it into

the hole until it contacts the innermost end of the

hole as illustrated in Fig. 2.

If you continue to turn the tool with slight pressure,

you can feel a spot where there is a hitch. At that

spot, pull the grip to the direction of an arrow mark

and insert the tool all the way until it hits the

innermost end.

(Standard socket

on the market)

(SDS max shank)

12.7 mm Chemical

Anchor Adaptor

19 mm Chemical

Anchor Adaptor

(1) Bull point

Overall length: 280, 400 mm

(1) Cold chisel

Overall length: 280, 400 mm

(1) Cutter

(1) Scoop

(2) Shank

(1) Bushing Tool

(2) Shank

(1) Rammer

150 × 150 mm

13 mm drill chuck

(13VLA)

Chuck adapter

(SDS max shank)

Chuck wrench

01Eng_DH50MRY_EE 08/4/24, 12:478

Содержание

Похожие устройства

English 1 Center pin Applied to core bits from 38 mm to 150 mm Applied to core bits 32 mm and 35 mm NOTE Do not use core bits 25 mm or 29 mm 2 Core bit External dia 25 29 32 35 38 45 54 64 79 94 105 120 150 mm with guide plate not applicable to cores 25 mm or 29 mm 3 Core bit shank Applied to core bits above 38 mm Applied to core bits below 35 mm 4 Drilling holes For drilling metal and wooden materials Hl 13 mm drill chuck 13VLA Chuck adapter SDS max shank 10 Surface Roughing Hammering 1 Bushing Tool 2 Shank 11 Tamping Hammering 1 Rammer 150 x 150 mm 2 Shank 12 Syringe for chip removal O Hammer grease A 500 g in a can 70 g in a green tube 30 g in a green tube Optional accessories are subject to change without notice Chuck wrench 5 Bolt placing operation with Chemical Anchor Rotation Hammering Standard socket on the market SDS max shank 12 7 mm Chemical Anchor Adaptor 19 mm Chemical Anchor Adaptor 6 Crushing Hammering 1 Bull point Overall length 280 400 mm 7 Groove digging and edging Hammering o 1 Cold chisel Overall length 280 400 mm 8 Asphalt cutting Hammering 1 Cutter 9 Scooping Work Hammering 1 Scoop APPLICATIONS O Drilling holes in concrete O Drilling anchor holes O Crushing concrete chipping by applying optional accessories digging and squaring PRIOR TO OPERATION 1 Power source Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate 2 Power switch Ensure that the power switch is in the OFF position If the plug is connected to a power receptacle while the power switch is in the ON position the power tool will start operating immediately which could cause a serious accident 3 Extension cord When the work area is removed from the power source use an extension cord of sufficient thickness and rated capacity The extension cord should be kept as short as practicable 4 How to install tool NOTE For tools such as a bull point and a cold chisel use only Hitachi genuine parts 1 Clean then smear the tool shank with the grease provided in the green tube Fig 1 2 To attach the tool SDS max shank insert it into the hole until it contacts the innermost end of the hole as illustrated in Fig 2 If you continue to turn the tool with slight pressure you can feel a spot where there is a hitch At that spot pull the grip to the direction of an arrow mark and insert the tool all the way until it hits the innermost end 8

Скачать