Hitachi CM7MRU [10/80] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi CM7MRU [10/80] English

Hitachi CM7MRU [10/80] English
9
English
SPECIFICATIONS
Model CM7MR CM7MRU CM7MC
Voltage (by areas)*
1
(110V, 230V)
Power input*
1
2000W, 2300W
No-load speed 6600 min
–1
Dimensions of diamond
Max. cutting depth 35mm
Max. cutting width 45mm
Weight (without cord and diamond wheel) 7.9kg 8.8kg
Starting current limiter*
2
No Yes No
*1 Be sure to check the nameplate on product as it is subject to change by areas.
*2 The starting current limiter produces the starting current to such an extent that a fuse (16 A, slow-blow)
is not tripped.
Outer dia. 180mm
Hole dia. 22.2mm
Thickness 1.5 - 2 mm
(Thickness of installation part.)
Kickback will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the wheel.
Corners, sharp edges or bouncing have a tendency
to snag the rotating wheel and cause loss of control
or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
f) Do not “jam” the wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or blinding of the wheel in
the cut and the possibility of kickback or wheel
breakage.
g) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the wheel
from the cut while the wheel is in motion otherwise
kickback may occur.
Investigate and take corrective action to eliminate
the cause of wheel binding.
h) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut.
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
i) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on
both sides of the wheel.
j) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
PRECAUTION ON USING WALL CHASER
1. Never operate these power tools without wheel
guards attached.
2. Do not over-reach when operating the wall chaser.
3. Check that the speed marked on the diamond wheels
or cutting wheel is equal to or greater than the rated
speed of the wall chaser.
4. Use only specified diamond wheels and cutting
wheels.
5. Diamond wheels and cutting wheels shall be stored
and handled with care in accordance with
manufacturer’s instructions.
6. Inspect the diamond wheel or cutting wheel before
use, do not use chipped, cracked or otherwise
defective products.
7. Always hold the body handle and top handle of the
power tool firmly. Otherwise the counter force
produced may result in inaccurate and even
dangerous operation.
8. Do not use separate reducing bushings or adapters
to adapt cutting wheels with a bore other than
22.2 mm.
9. Do not use this machine to cut asbestos.
10. The diamond wheels continue to rotate after the
tool is switched off.
11. Wear a dust mask
Do not inhale the harmful dusts generated in cutting
operation. The dust can endanger the health of
yourself and bystanders.
STANDARD ACCESSORIES
(1) 22 mm Wrench ......................................................... 1
(2) Side handle ................................................................ 1
Standard accessories are subject to change without notice.
APPLICATION
Cutting slits in concrete, cement, brick or tiles. Slits can
then be chipped with a separate tool to make grooves for
laying plumber's piping or cable trunking.
01Eng_CM7MR_EE 11/25/08, 21:419

Содержание

Похожие устройства

English d e f g h i Kickback will propel the tool in direction opposite to the wheel s movement at the point of snagging Use special care when working corners sharp edges etc Avoid bouncing and snagging the wheel Corners sharp edges or bouncing have a tendency to snag the rotating wheel and cause loss of control or kickback Do not attach a saw chain woodcarving blade or toothed saw blade Such blades create frequent kickback and loss of control Do not jam the wheel or apply excessive pressure Do not attempt to make an excessive depth of cut Overstressing the wheel increases the loading and susceptibility to twisting or blinding of the wheel in the cut and the possibility of kickback or wheel breakage When wheel is binding or when interrupting a cut for any reason switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop Never attempt to remove the wheel from the cut while the wheel is in motion otherwise kickback may occur Investigate and take corrective action to eliminate the cause of wheel binding Do not restart the cutting operation in the workpiece Let the wheel reach full speed and carefully re enter the cut The wheel may bind walk up or kickback if the power tool is restarted in the workpiece Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback Large workpieces tend to sag under their own weight Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel jl Use extra caution when making a pocket cut into existing walls or other blind areas The protruding wheel may cut gas or water pipes electrical wiring or objects that can cause kickback PRECAUTION ON USING WALL CHASER 1 Never operate these power tools without wheel guards attached 2 Do not over reach when operating the wall chaser 3 Check that the speed marked on the diamond wheels or cutting wheel is equal to or greater than the rated speed of the wall chaser 4 Use only specified diamond wheels and cutting wheels 5 Diamond wheels and cutting wheels shall be stored and handled with care in accordance with manufacturer s instructions 6 Inspect the diamond wheel or cutting wheel before use do not use chipped cracked or otherwise defective products 7 Always hold the body handle and top handle of the power tool firmly Otherwise the counter force produced may result in inaccurate and even dangerous operation 8 Do not use separate reducing bushings or adapters to adapt cutting wheels with a bore other than 22 2 mm 9 Do not use this machine to cut asbestos 10 The diamond wheels continue to rotate after the tool is switched off 11 Wear a dust mask Do not inhale the harmful dusts generated in cutting operation The dust can endanger the health of yourself and bystanders SPECIFICATIONS Model CM7MR Voltage by areas Power input CM7MC 2000W 2300W No load speed 6600 min Outer dia 180mm Hole dia 22 2mm Thickness 1 5 2 mm Thickness of installation part Dimensions of diamond Max cutting depth 35mm Max cutting width 45mm Weight without cord and diamond wheel Starting current limiter 2 CM7MRU 110V 230V 7 9kg No I 8 8kg Yes No 1 Be sure to check the nameplate on product as it is subject to change by areas 2 The starting current limiter produces the starting current to such an extent that a fuse 16 A slow blow is not tripped STANDARD ACCESSORIES APPLICATION 1 22 mm Wrench 1 21 Side handle 1 Standard accessories are subject to change without notice Cutting slits in concrete cement brick or tiles Slits can then be chipped with a separate tool to make grooves for laying plumber s piping or cable trunking 9

Скачать