Home
Главная
Metabo
Водяной Насос
P 3000 G
Инструкция по эксплуатации Страница: 10

Metabo P 3000 G [10/44] English

ENGLISH

sion cords; protect from sharp

edges, oil and heat.

 Place extension cable so that it can

not get into the fluid to be pumped.

 Unplug:

 prior to

all servicing;

 when

persons are in the swim-

ming pool or garden pond.



Danger by pump failures!

 If you

notice transport damage while

unpacking, notify your supplier

immediately. Do not operate the

machine!

 Be

fore each use check the pump,

especially the power cable and plug

for possible damage. Risk of fatal

electric shock!

 A damaged pump must be work-

manlike repaired before it can be

used again.

 Do not attempt to repair the equip-

ment yourself! Only trained special-

ists are permitted to service or repair

pumps or pressure vessel

Caution!

To avoid water damage, e.g.

flooded rooms, caused by pump mal-

functions or defects:

 provide for suitable safety measures

such as the following:

 alarm or

 colle

ction tank with monitoring.

The manufacturer is not liable for any

damage caused by:

 imprope

r use of the pump;

 overloading of the pump through

continous operation;

 fa

ilure to operate and store the

pump in a frost-free environment;

 unauthorised modification of the

pump (repairs to electrical equip-

ment may only be carried out by

qua

lified electricians!);

 use of spare

parts which have not

been tested and approved by the

manufacturer; or

 use of unsuitable installation materi-

als (fittings, connection lines etc.).

Suitable installation materials:

 pressure-resi

stant (min. 10 bar)

 hea

t-resistant (min. 100°C).

The equipment is easily assembled and

connected. 

If in doubt, contact your specialist sup-

plier or qualified electrician.

5.1 Installation

 The equipment must be placed on a

plane and level surface, suitable of

bearing the weight of the equipment

fully filled with water.

 Um Vib

rationen zu vermeiden, sollte

das Gerät auf eine elastische Unter-

lage gestellt werden.

 The installation location should be

well vented and protected from

atmospheric exposure.

 When operated at garden ponds

and pools the equipment must be

set up safe against flooding and pro-

tected from falling into the water.

Any a

dditional legal requirements

are to be observed.

5.2 Suction line connection

Note: 

Possibly further accessories may

be required for connection (see “Availa-

ble Accessories”).

Caution! 

The suction line needs to be

installed in such manner that it does

not exert mechanical force or distor-

tion to the pump.

Caution! 

When pumping contaminated

fluids install a suction strainer to pro-

tect pump from sand and dirt.

Note: 

A check valve is recommended to

prevent water backflow when the pump

is switched off.

 All screw fittings are to be sealed

with thread sealing tape; leakages

cause priming of air and reduce or

prevent the priming of water.

 The

suction line should be of at least

1" (25 mm) inner diameter; it must

be resistent to

buckling and vacuum

proof.

 Keep suction line as short as practi-

cal, since with increasing length the

pump capacity is reduced.

 The

suction line should raise

towards the pump to prevent air

locks.

 A sufficient water supply must be

ensured, the foot valve at the end of

the suction line must be submerged

in water at all times.

5.3 Discharge port

Note: 

Possibly further accessories may

be required for connection (see “Availa-

ble Accessories”).

Caution! 

The discharge (or pressure)

ne needs to be installed in such

manner that it does not exert mechan-

ical force or distortion to the pump.

 All screw fitti

ngs should be sealed

with thread sealing tape to prevent

leakage.

 All parts of the pressure line must be

resistant to internal pressure.

 All parts of the pressure line must be

installed in a workmanlike manner.

Danger! 

Improper installation and use

of parts not resistant to internal pres-

sure can cause the pressure line to

bre

ak during operation. Risk of per-

sonal injury by liquid spurting from

the line under high pressure!

5.4 Mains connection

Danger! Risk of electric shock! 

Do not operate the equipment

wet environment and only under

the following conditions:

 Connect only to an earthed outlet

that is properly installed, earthed

and tested.

 Mains voltage and fuse protection

must correspond to those stated

in the “Technical Specications”.

 When operated at pools, garden

ponds and similar locations, the

equipment must be protected by

a residual current operated

device (RCD, 30 mA) (DIN VDE

010

0 -702, -738 or equivalent

applicable local regulations). 

We recommend the use of RCD's

as a ge

neral precaution for per-

sonal protection.

 When used outdoors all electri-

cal connections must be of the

splash-proof type; thez must

not

be placed in water.

 Use only extension cables of suf-

ficient lead cross section (see

“Technical Specifications”).

Unroll cable reels fully.

5.5 Filling the pump and

priming

Caution! 

After installation, loss of water

or priming of air the pump needs to

be filled with water. Starting the pump

without water causes damage!

Note: 

The suction line does not need to

be filled, the pump is self-priming. How-

ever, depending on length and diameter

of the

suction line it may take some time

until pressure has built up.

1. Remove the water filler plug, com-

plete with gasket.

5. Prior to Operation

Metabo P 3000 G [10/44] English

Содержание

Похожие устройства