Home
Главная
Skil
Циркулярная Пила
5255 LA
Инструкция по эксплуатации Страница: 9

Skil 5255 LA Инструкция по эксплуатации онлайн [9/164] 92569

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY WARNINGS FOR CIRCULAR SAWS

1) CUTTING PROCEDURES

DANGER : Keep hands away from cutting area

and the blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are holding the

saw, they can not be cut by the blade.

b) Do not reach underneath the workpiece. The guard

cannot protect you from the blade below the workpiece.

c) Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

d) Never hold the workpiece being cut in your hands or

across your leg. Secure the workpiece to a stable

platform. It is important to support the work properly to

minimize body exposure, blade binding, or loss of control.

e) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring or its own

cord. Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

f) When ripping always use a parallel guide or straight

edge guide. This improves the accuracy of cut and

reduces the chance of blade binding.

g) Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades that

do not match the mounting hardware of the saw will run

eccentrically, causing loss of control.

h) Never use damaged or incorrect blade washers or

bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation.

2) KICKBACK CAUSES AND RELATED WARNINGS

• Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift

up and out of the workpiece toward the operator

• When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator

• If the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the

kerf and jump back towards operator

• Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below

a) Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the

operator, if proper precautions are taken.

b) When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop. Never attempt to remove the saw

from the work or pull the saw backwards while the

blade is in motion or kickback may occur. Investigate

and take corrective actions to eliminate the cause of

blade binding. Avoid cutting nails or screws.

c) When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are

not engaged into the material. If saw blade is binding,

it may walk up or kickback from the workpiece as the saw

is restarted.

d) Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must

be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding and

kickback.

g) Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

3) LOWER GUARD FUNCTION

a) Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie

the lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent.

Disconnect the plug, raise the lower guard with the

retracting handle and make sure it moves freely and does

not touch the blade or any other part, in all angles and

depths of cut.

b) Check the operation of the lower guard spring. If the

guard and the spring are not operating properly,

they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Lower guard should be retracted manually only for

special cuts such as plunge cuts and compound

cuts. Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

d) Always observe that the lower guard is covering the

blade before placing saw down on bench or floor.

An unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path. Be aware

of the time it takes for the blade to stop after switch is

released.

ADDITIONAL SAFETY WARNINGS

GENERAL

• This tool should not be used by people under the age of

16 years

• This tool is not suitable for wet cutting

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

Содержание

Похожие устройства

account the working conditions and the work to be performed Use of the power tool for operations diflerent from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained motionless in the material until the blade comes to a complete stop Never attempt to remove the saw from the work or pull the saw backwards while the blade Is In motion or kickback may occur Investigate and take corrective actions to eliminate the cause of blade binding Avoid cutting nails or screws c When restarting a saw in the workpiece centre the saw blade In the kerf and check that saw teeth are not engaged Into the material If saw blade is binding it may walk up or kickback from the workpiece as the saw is restarted d Support large panels to minimise the risk of blade pinching and kickback Large panels tend to sag under their own weight Supports must be placed under the panel on both sides near the line of cut and near the edge of the panel e Do not use dull or damaged blades Unsharpened or improperly set blades produce narrow kerf causing excessive friction blade binding and kickback f Blade depth and bevel adjusting locking levers must be tight and secure before making cut If blade adjustment shifts while cutting it may cause binding and kickback g Use extra caution when sawing Into existing walls or other blind areas The protruding blade may cut objects that can cause kickback 3 LOWER GUARD FUNCTION a Check lower guard for proper closing before each use Do not operate the saw If lower guard does not move freely and close Instantly Never clamp or tie the lower guard into the open position If saw is accidentally dropped lower guard may be bent Disconnect the plug raise the lower guard with the retracting handle and make sure it movesfreely and does not touch the blade or any other part in all angles and depths of cut b Check the operation of the lower guard spring If the guard and the spring are not operating properly they must be serviced before use Lower guard may operate sluggishly due to damaged parts gummy deposits or a build up of debris c Lower guard should be retracted manually only for special cuts such as plunge cuts and compound cuts Raise lower guard by retracting handle and as soon as blade enters the material the lower guard must be released For all other sawing the lower guard should operate automatically d Always observe that the lower guard is covering the blade before placing saw down on bench or floor An unprotected coasting blade will cause the saw to walk backwards cutting whatever is in its path Be aware of the time it takes for the blade to stop after switch is released SAFETY WARNINGS FOR CIRCULAR SAWS 1 CUTTING PROCEDURES a 0 DANGER Keep hands away from cutting area and the blade Keep your second hand on auxiliary handle or motor housing If both hands are holding the saw they can not be cut by the blade b Do not reach underneath the workpiece The guard cannot protect you from the blade below the workpiece c Adjust the cutting depth to the thickness of the workpiece Less than a full tooth of the blade teeth should be visible below the workpiece d Never hold the workpiece being cutin your hands or across your leg Secure the workpiece to a stable platform It is important to support the work properly to minimize body exposure blade binding or loss of control e Hold the power tool by insulated gripping surfaces only when performing an operation where the cutting tool may contact hidden wiring or Its own cord Contact with a live wire will also make exposed metal parts of the power tool live and could give the operator an electric shock f When ripping always use a parallel guide or straight edge guide This improves the accuracy of cut and reduces the chance of blade binding g Always use blades with correct size and shape diamond versus round of arbour holes Blades that do not match the mounting hardware of the saw will run eccentrically causing loss of control h Never use damaged or incorrect blade washers or bolt The blade washers and boltwere specially designed for your saw for optimum performance and safety of operation 2 KICKBACK CAUSES AND RELATED WARNINGS Kickback is a sudden reaction to a pinched bound or misaligned saw blade causing an uncontrolled saw to lift up and out of the workpiece toward the operator When the blade is pinched or bound tightly by the kerf closing down the blade stalls and the motor reaction drives the unit rapidly back toward the operator If the blade becomes twisted or misaligned in the cut the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back towards operator Kickback I s th e result of tool misuse and or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below a Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces Position your body to either side of the blade but not In line with the blade Kickback could cause the saw to jump backwards but kickback forces can be controlled by the operator if proper precautions are taken b When blade is binding or when interrupting a cut for any reason release the trigger and hold the saw ADDITIONAL SAFETY WARNINGS GENERAL This tool should not be used by people under the age of 16 years Thi s tool is not suitable for wet cutting Always disconnect plug from power source before making any adjustment or changing any accessory 9

Скачать