Home
Главная
Kramer
Преобразователи и Расширители Интерфейсов
FC-26
Руководства по эксплуатации Страница: 22

Kramer FC-26 [22/68] Connecting to the fc 26 via rs 232 or ir

Connecting the FC-26

6.1.3 Connecting to the FC-26 via RS-232 or IR

To connect to the FC-26 via RS-232:

 Connect the RS-232, 3-pin, terminal block connectors on the rear panel of

the FC-26 using 3-wire cable (pin TX to pin 2, RX to pin 3, and G to pin 5) to

the RS-232 9-pin D-sub port on the devices to be controlled

To connect to the FC-26 via IR either:

 Connect an IR blaster to one of the IR Outputs and place it within 4m to 8m

(13 to 26ft) and in line-of-sight of the device to be controlled

—OR—

 Connect an IR emitter cable to one of the IR Outputs and stick the emitter to

the IR sensor on the device to be controlled

Содержание

User manual 1
Contents 4
Figures 4
Introduction 6
Achieving the best performance 7
Getting started 7
Safety instructions 7
Recycling kramer products 8
Overview 9
About the power over ethernet feature 11
Defining the fc 26 ethernet controller 12
Figure 2 defines the front panel of the fc 26 12
Figure 3 defines the rear panel of the fc 26 13
Configuring the fc 26 ethernet controller 14
Initial configuration and use overview 14
Configuring a virtual port on the pc 16
Setting up an ethernet connection on the pc 16
Connecting the fc 26 17
Connecting the ethernet port directly to a pc 18
Connecting via ethernet 18
Connecting the ethernet port via a network hub or switch 21
Connecting to the fc 26 via rs 232 or ir 22
Browsing the web pages 23
Remote operation via the web pages 23
Loading and saving configurations 24
Connected clients page 25
Device settings page 26
Communication page 28
Serial port settings page 29
Ir command learner page 30
Not available for normal operation 30
Note while learning is in progress the four ir out leds light and the fc 26 is 30
The ir command learner page allows you to teach the fc 26 ir commands 30
These can be saved for later use 30
On the security page click on 31
Security page 31
The confirmation popup is displayed as shown in figure 18 31
The security page allows you to turn logon authentication on or off 31
To activate web page security 31
Valid user and password for default logon credentials see section 10 31
When security is on access to the web pages is granted only on submission of a 31
Logs page 33
About us page 34
Configuring and maintaining the fc 26 36
Ir learning 36
Resetting to the factory default settings 37
Upgrading the firmware 37
Technical specifications 38
Data handling performance 39
Example bandwidth calculation 39
Default communication parameters 40
Default logon authentication 40
Ip address after performing a factory reset the dhcp and the ip address are set 40
Note the fc 26 is dispatched from the factory with dhcp enabled and a random 40
To the values shown below 40
Command string 41
Device long response 41
Device message format 41
Host message format 41
Kramer protocol 3000 41
Kramer protocol 3000 syntax 41
Simple command 41
Command terms 42
Chaining commands 43
Command forms 43
Entering commands 43
Maximum string length 43
Kramer protocol 3000 command list 44
Kramer protocol 3000 detailed commands 45
This section lists the detailed commands applicable to the fc 26 45
Ir status 66
Ir transmit status 66
Parameters 66
Parity types 66
Serial types 66

Kramer FC-26 [22/68] Connecting to the fc 26 via rs 232 or ir

Содержание

Похожие устройства