![Kramer FC-26 [4/68] Contents](/img/pdf.png)
Kramer FC-26 [4/68] Contents
![Kramer FC-26 [4/68] Contents](/views2/1152649/page4/bg4.png)
Contents
i
Contents
1 Introduction 1
2 Getting Started 2
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 2
2.3 Recycling Kramer Products 3
3 Overview 4
3.1 About the Power over Ethernet Feature 6
4 Defining the FC-26 Ethernet Controller 7
5 Initial Configuration and Use Overview 9
5.1 Configuring the FC-26 Ethernet Controller 9
5.2 Configuring a Virtual Port on the PC 11
5.3 Setting Up an Ethernet Connection on the PC 11
6 Connecting the FC-26 12
6.1 Connecting via Ethernet 13
7 Remote Operation via the Web Pages 18
7.1 Browsing the Web Pages 18
7.2 Connected Clients Page 20
7.3 Device Settings Page 21
7.4 Communication Page 23
7.5 Serial Port Settings Page 24
7.6 IR Command Learner Page 25
7.7 Security Page 26
7.8 Logs Page 28
7.9 About Us Page 29
8 Configuring and Maintaining the FC-26 31
8.1 IR Learning 31
8.2 Resetting to the Factory Default Settings 32
8.3 Upgrading the Firmware 32
9 Technical Specifications 33
9.1 Data Handling Performance 34
9.2 Example Bandwidth Calculation 34
10 Default Communication Parameters 35
11 Kramer Protocol 3000 36
11.1 Kramer Protocol 3000 – Syntax 36
11.2 Kramer Protocol 3000 – Command List 39
11.3 Kramer Protocol 3000 – Detailed Commands 40
11.4 Parameters 61
Figures
Figure 1: FC-26 Controlling Devices Remotely Using K-Touch 3.0 over a LAN 5
Figure 2: FC-26 Ethernet Controller Front Panel 7
Figure 3: FC-26 Ethernet Controller Rear Panel 8
Figure 4: Connecting the FC-26 for Initial Configuration 9
Figure 5: Configuring a Remote Connection 11
Figure 6: Connecting the FC-26 Ethernet Controller 12
Figure 7: Local Area Connection Properties Window 14
Содержание
- User manual 1
- Contents 4
- Figures 4
- Introduction 6
- Achieving the best performance 7
- Getting started 7
- Safety instructions 7
- Recycling kramer products 8
- Overview 9
- About the power over ethernet feature 11
- Defining the fc 26 ethernet controller 12
- Figure 2 defines the front panel of the fc 26 12
- Figure 3 defines the rear panel of the fc 26 13
- Configuring the fc 26 ethernet controller 14
- Initial configuration and use overview 14
- Configuring a virtual port on the pc 16
- Setting up an ethernet connection on the pc 16
- Connecting the fc 26 17
- Connecting the ethernet port directly to a pc 18
- Connecting via ethernet 18
- Connecting the ethernet port via a network hub or switch 21
- Connecting to the fc 26 via rs 232 or ir 22
- Browsing the web pages 23
- Remote operation via the web pages 23
- Loading and saving configurations 24
- Connected clients page 25
- Device settings page 26
- Communication page 28
- Serial port settings page 29
- Ir command learner page 30
- Not available for normal operation 30
- Note while learning is in progress the four ir out leds light and the fc 26 is 30
- The ir command learner page allows you to teach the fc 26 ir commands 30
- These can be saved for later use 30
- On the security page click on 31
- Security page 31
- The confirmation popup is displayed as shown in figure 18 31
- The security page allows you to turn logon authentication on or off 31
- To activate web page security 31
- Valid user and password for default logon credentials see section 10 31
- When security is on access to the web pages is granted only on submission of a 31
- Logs page 33
- About us page 34
- Configuring and maintaining the fc 26 36
- Ir learning 36
- Resetting to the factory default settings 37
- Upgrading the firmware 37
- Technical specifications 38
- Data handling performance 39
- Example bandwidth calculation 39
- Default communication parameters 40
- Default logon authentication 40
- Ip address after performing a factory reset the dhcp and the ip address are set 40
- Note the fc 26 is dispatched from the factory with dhcp enabled and a random 40
- To the values shown below 40
- Command string 41
- Device long response 41
- Device message format 41
- Host message format 41
- Kramer protocol 3000 41
- Kramer protocol 3000 syntax 41
- Simple command 41
- Command terms 42
- Chaining commands 43
- Command forms 43
- Entering commands 43
- Maximum string length 43
- Kramer protocol 3000 command list 44
- Kramer protocol 3000 detailed commands 45
- This section lists the detailed commands applicable to the fc 26 45
- Ir status 66
- Ir transmit status 66
- Parameters 66
- Parity types 66
- Serial types 66
Похожие устройства
- Kramer FC-50 Руководства по эксплуатации
- Kramer VP-14 Руководства по эксплуатации
- Kramer VP-14xl Руководства по эксплуатации
- Kramer PL-50 Руководства по эксплуатации
- Kramer RB-6 Руководства по эксплуатации
- Kramer PL-15 Руководства по эксплуатации
- Kramer PT-4iREX Руководства по эксплуатации
- Kramer PT-5R/T Руководства по эксплуатации
- Kramer 401DN Руководства по эксплуатации
- Kramer 401C Руководства по эксплуатации
- Kramer VP-100 Руководства по эксплуатации
- Kramer 7408 Руководства по эксплуатации
- Ritmix RAT-310 Инструкция по эксплуатации
- Ritmix RAT-501 Инструкция по эксплуатации
- Ritmix RAT-201 Инструкция по эксплуатации
- Kramer 7508 Руководства по эксплуатации
- Kramer FC-7501 Руководства по эксплуатации
- Kramer FC-331 Руководства по эксплуатации
- Kramer FC-332 Руководства по эксплуатации
- Kramer FC-113 Руководства по эксплуатации