![OKI ml5100fb [39/53] Problem cause action](/img/pdf.png)
OKI ml5100fb [39/53] Problem cause action
![OKI ML5100FBeco [39/53] Problem cause action](/views2/1074038/page39/bg27.png)
Troubleshooting > 39
Print position offset
The horizontal printing
position is offset.
The start position may
change after the printer is
powered on.
When the printer is powered
ON, switch from off-line mode
to on-line mode by pressing
the SEL button. Reset the
start position. You must set
the Power Switch to OFF
before you change the start
position.
Printing slows down
Print direction changes
suddenly to unidirectional.
When the print head
overheats, the printer
automatically starts
unidirectional split printing.
When the print head
temperature drops
sufficiently, the printer will
return to its original
operation.
PE warning
The print carriage does not
operate.
There is contamination on the
carriage shaft.
Clean any paper dust and
contamination from the
carriage with a dry cloth.
Print blurring
The characters are too pale to
display properly on the paper.
The Paper Thickness lever
position does not match the
paper.
Correct the Paper Thickness
lever setting.
The printer is set to print at
high speed.
Set the speed to normal.
The ribbon has reached its
end of life.
Replace the ribbon by a new
one.
The ribbon cartridge is not
installed correctly.
Reinstall the ribbon cartridge
correctly.
The ribbon has been wound
incorrectly.
Replace the ribbon cartridge
by a new one.
The ribbon is not transferring
properly.
Replace the ribbon cartridge
by a new one.
A line of print is missing. Broken wire pins. Contact your dealer.
The printout differs from the screen display.
Printout of completely
different characters or
symbols.
Incorrect print setup for the
user application.
Reselect print setup for the
applications according to
priority.
The application control codes
for the previous print
operation are still enabled.
Initialise the printer.
The input application control
signal is not correct.
Print in hex dump mode and
verify the data content. Make
corrections in the application.
The interface cable is not
properly connected.
Reconnect the cable correctly.
PROBLEM CAUSE ACTION
Содержание
- Preface 2
- Reface 2
- Anufacturer 3
- Authorised representative 3
- Environmental information 3
- Importer to the eu authorised representative 3
- Manufacturer 3
- Mporter to th 3
- Nformation 3
- Nvironmenta 3
- Contents 4
- Ontents 4
- Caution 6
- Cautions and warnings 6
- Notes cautions and warnings 6
- Warning 6
- About this guide 7
- Introduction 7
- Ntroduction 7
- On line usage 7
- Printing pages 8
- Etting started 9
- Front view 9
- Getting started 9
- Identifying component parts 9
- Retaining packing materials 9
- Warning 9
- Locating your printer 10
- Ocating your printer 10
- Rear view 10
- Owering on your printer 11
- Powering on your printer 11
- Warning 11
- Caution 12
- Producing a test print 12
- Roducing a test print 12
- Caution 13
- Connecting to a computer 13
- Interconnecting printer and computer 13
- Interconnection 13
- Interfaces 13
- Onnecting to a computer 13
- Installing the printer driver 14
- Nstalling the printer driver 14
- Printing a test page 14
- Rinting a test page 14
- Printing from a computer 15
- Aper handling 16
- Loading cut sheet paper 16
- Paper handling 16
- Ejecting cut sheet paper 17
- Jecting cut sheet paper 17
- Feeding continuous forms 18
- Loading continuous forms 18
- Setting up continuous forms 18
- Earing off continuous forms 20
- Tearing off continuous forms 20
- Aligning the tear off perforations 21
- Emoving continuous forms 21
- Removing continuous forms 21
- Close the pin tractor covers 22
- Etting th 22
- Hickness lever 22
- Lift the pin tractor covers 1 and remove the forms 22
- Set the paper thickness lever for different paper types as follows 22
- Setting the paper thickness lever 22
- There are 9 lever positions the first 9 for printing purposes and the ninth to also facilitate ribbon replacement 22
- Do not print bankbooks to avoid possible pin breakage ribbon snagging 23
- If the lever position does not suit the paper thickness paper feeding and printing may not work properly 23
- Overall paper thickness lever position 23
- Printing can be carried out with the lever position set to 4 for paper thickness up to 0 25mm 23
- Printing with lever positions 5 9 is not guaranteed 23
- Set the paper thickness lever for overall paper thickness as follows 23
- When lever positions 5 9 are selected printing quality for carbon paper may decline resulting in illegible characters for example 23
- Indicators 24
- Ndicators 24
- Operating instructions 24
- Operator panel 24
- Perating instructions 24
- Perator panel 24
- Button switches 25
- Switch status function 25
- Utton switches 25
- Confirming current settings 26
- Etting menu values 26
- Menu setting 26
- Setting menu values 26
- Enu items and settings 27
- In the menu settings tables below factory default settings are shown emboldened 27
- Item function setting 27
- Menu items and settings 27
- Item function setting 28
- Item function setting 29
- Item function setting 30
- Item function setting 31
- Item function setting 32
- Adjusting tof position 33
- Djustin 33
- For cut sheet mode do not insert the paper at this stage 33
- In continuous forms mode press the load park button 33
- In cut sheet manual feeding mode press the load park button and place the paper on the paper tray 33
- Initialising menu settings 33
- Position 33
- Press and hold down the sel and load park buttons together then set the power switch to on 33
- Print out the menu settings of the printer as in confirming current settings on page 26 and confirm that the tof in cut sheet mode or continuous forms mode is 6 5 mm 0 5 in 33
- Set the paper type lever to the required paper type 33
- Set the power switch to off 33
- To restore the menu settings to their initial values carry out the steps below 33
- Use the following procedure to set tof to accord with the reference position 6 5 mm 0 5 in the reference position refers to the first line of the paper i e the position to which the printer feeds the paper when automatically loading the paper 33
- When continuous forms are used place the paper on the pin tractor 33
- Caution 34
- Printer impact mode 34
- Printer settings 34
- Rinter settings 34
- Clearing paper jams 35
- Cut sheet paper jammed in printer 35
- Roubleshooting 35
- Troubleshooting 35
- Continuous forms jammed in printer 37
- Warning 37
- Esponding to alarm conditions 38
- Esponding to general problems 38
- Indicator alarm meanings and actions 38
- Problem cause action 38
- Responding to alarm conditions 38
- Responding to general problems 38
- Sel alarm 38
- Use the following table for guidance on how to respond to indicated alarm conditions 38
- Use the following table to help you to identify symptoms with possible causes and take suggested remedial actions 38
- Problem cause action 39
- Problem cause action 40
- Problem cause action 41
- Problem cause action 42
- Caution 43
- Cleaning your printer 43
- Leaning your printer 43
- Printer exterior 43
- Printer interior 43
- Warning 43
- Caution 44
- Do not clean any interior working parts with the suction nozzle to avoid possible damage to the printer 44
- Using a soft cloth cotton swabs and a vacuum cleaner clean the interior of the printer as follows 44
- When you clean the interior of the printer with a vacuum cleaner do not attempt to clean any parts smaller than the suction nozzle 44
- Where to clean what to clean 44
- Changing a ribbon cartridge 45
- Consumables 45
- Consumables and accessories 45
- Onsumables and accessories 45
- Caution 48
- Item specification 49
- Pecifications 49
- Specifications 49
- Ki contact details 51
- Oki contact details 51
Похожие устройства
- OKI ml3391eco Инструкция по эксплуатации
- OKI ml3390 Инструкция по эксплуатации
- OKI ml1190 Инструкция по эксплуатации
- OKI ml5720 Инструкция по эксплуатации
- OKI ml5521eco Инструкция по эксплуатации
- OKI ml4410 Инструкция по эксплуатации
- OKI ml3410 Инструкция по эксплуатации
- OKI ml3320 Инструкция по эксплуатации
- OKI ml280 elite dc Инструкция по эксплуатации
- OKI ml1120 Инструкция по эксплуатации
- Nikon coolpix l340 black Инструкция по эксплуатации
- Nikon coolpix s3700 black Инструкция по эксплуатации
- Nikon d750 kit 24-120mm f/4g ed vr black Инструкция по эксплуатации
- Nikon coolpix s3700 silver Инструкция по эксплуатации
- Nikon coolpix s2900 silver Инструкция по эксплуатации
- Nikon coolpix aw130 diving kit, camouflage Инструкция по эксплуатации
- Nilfisk Alto c100.6-5 Инструкция по эксплуатации
- Office Kit l 3223 Инструкция по эксплуатации
- Office Kit s 150 Инструкция по эксплуатации
- Office Kit s 140 Инструкция по эксплуатации