Home
Главная
Stiga
Газонокосилка
COMBI 48
Инструкция по эксплуатации Страница: 26

Stiga COMBI 48 [26/92] En standards of use

STANDARDS OF USE

For instructions regarding the engine and the battery (if

supplied), read the relevant manuals.

NOTE - The number which precedes each paragraph links the

references in the text to the respective figures (listed on the pa-

ges 2 - 3).

NOTE - The machine can be supplied with some of the

components already fitted.

WARNING - Unpacking and completing the assembly

should be done on a flat and stable surface, with enough

space for machine handling and its packaging, always

making use of suitable equipment.

Disposal of the packaging should be done in accordance

with the local regulations in force.

Complete machine assembly following the indications on the

instruction sheets enclosed with each part to be assembled.

NOTE - The meanings of the symbols on controls are

explained on page 4 and following.

Throttle trigger

The throttle is controlled by the lever (1). Lever positions are

indicated on the relevant plate.

Some models have a fixed speed, and therefore no need of a

throttle.

Blade brake lever

The blade brake is controlled by the lever (1) which must be

held against the handle for ignition and during lawnmower

operations.

The engine stops when the lever is released.

Drive engagement lever

In power-driven models, draw the lever (1) towards the handle

for forward movement.

The lawnmower stops moving forward when the lever is

released.

Cutting height adjustment

The cutting height is adjusted using the levers (1).

The four wheels must be at the same height.

MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE IS

STOPPED.

NOTE - This machine cuts lawns in various modes; before

starting work, prepare the machine based on how the lawn is

to be mowed.

MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF.

Preparation for grass cutting and collection in

grass-catcher:

– Lift the rear stone-guard (1) and correctly hook on the grass-

catcher (2) as shown in the figure.

Preparation for grass cutting and rear discharge:

– Remove the grass-catcher and check that the rear stone-

guard (1) maintains its lowered position;

3.1b

3.1a

3. GRASS CUTTING

2.4

2.3

2.2

2.1

2. DESCRIPTION OF CONTROLS

1. FINISH ASSEMBLY

Preparation for grass cutting and mulching (if pres-

ent):

– In models with side discharge potential: make sure the side

door (4) is lowered.

– Lift the rear stone-guard (1) and fit the deflector cap (5) in the

outlet, keeping it slightly tilted to the right. Fasten it by fitting

the two pins (6) into the holes provided until the fastener

tooth clicks into place (7).

To remove the deflector cap (5), lift the stone-guard (1) and

press down on the centre until the tooth (7) is released.

Starting the engine

To start, follow the instructions in the engine manual, pull the

blade brake lever (1) against the handle and firmly pull the

starter cable knob (2).

If the model has electric ignition pull the blade brake lever (1)

against the handle and turn the starter key (3).

Grass cutting

• In case of “mulching” or rear dumping of grass: always

avoid removing a large quantity of grass. Never cut more

than one third the total grass height in a single passage!

Regulate the forward speed according to the lawn conditions

and the amount of grass removed.

LAWN CARE RECOMENDATIONS

Each type of grass has different features and may thus require

different ways to care for the lawn; always read the instructions

on seed boxes for mowing height for the growth conditions in

the work area.

Keep in mind that most grass is made up of a stem and one or

more leaves. If leaves are fully cut, the lawn is damaged and

growth is more difficult.

The following indications generally apply:

– too low a cut causes grass tears and uprooting, with a “spot-

ted” aspect;

– in the summer, cutting must be higher to avoid the ground

from drying;

– do not cut wet grass; this could reduce blade efficiency due

to sticky grass and tear the lawn;

– for particularly high grass, initially mow at maximum admit-

ted machine height followed by a second mow after two or

three days.

The appearance of the lawn will improve if you alternate the

cutting in both directions at the same height.

End of operations

When the work has been completed, release the brake lever (1)

and disconnect the spark plug cap (2).

WAIT UNTIL THE BLADE STOPS before performing any work.

IMPORTANT - Regular, careful maintenance is essential for

keeping the safety level and original performance of the

machine unchanged in time.

Store the lawnmower in a dry place.

1) Wear strong working gloves during any cleaning, mainte-

nance or adjustment operation on the machine.

2) Carefully clean the machines with water after each cut;

remove the grass debris and mud accumulated inside the

chassis to avoid their drying and thus making the next start-

up difficult.

3) The paintwork on the inside of the chassis may peel off in

time due to the abrasive action of the cut grass; in this case,

intervene promptly by touching up the paintwork using a

4. ROUTINE MAINTENANCE

3.4

3.3

3.2

3.1c

Содержание

Похожие устройства

EN STANDARDS OF USE For instructions regarding the supplied read the relevant manuals engine 3 1c and the battery if NOTE The number which precedes each paragraph links the references in the text to the respective figures listed on the pa ges 2 3 I 1 FINISH ASSEMBLY NOTE The machine components already fitted can Preparation for grass cutting and mulching if pres ent In models with side discharge potential make sure the side door 4 is lowered Lift the rear stone guard 1 and fit the deflector cap 5 in the outlet keeping it slightly tilted to the right Fasten it by fitting the two pins 6 into the holes provided until the fastener tooth clicks into place 7 To remove the deflector cap 5 lift the stone guard 1 and press down on the centre until the tooth 7 is released be supplied with some of the WARNING Unpacking and completing the assembly should be done on a flat and stable surface with enough space for machine handling and its packaging always making use of suitable equipment Disposal of the packaging should be done in accordance with the local regulations in force Complete machine assembly following the indications instruction sheets enclosed with each part to be assembled on 2 DESCRIPTION OF CONTROLS NOTE The meanings of the explained on page 4 and following symbols the on controls are I 2 1 Throttle trigger The throttle is controlled by the lever 1 Lever positions are indicated on the relevant plate Some models have a fixed speed and therefore no need of a throttle I 2 2 Blade brake lever The blade brake is controlled by the lever 1 which must be held against the handle for ignition and during lawnmower operations The engine stops when the lever is released I 2 3 Drive engagement lever In power driven models draw the lever 1 towards the handle for forward movement The lawnmower stops moving forward when the lever is released I 2 4 Cutting height adjustment The cutting height is adjusted using the levers 1 The four wheels must be at the same height MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE IS STOPPED I 3 2 starting the engine To start follow the instructions in the engine manual pull the blade brake lever 1 against the handle and firmly pull the starter cable knob 2 If the model has electric ignition pull the blade brake lever 1 against the handle and turn the starter key 3 I 3 3 Grass cutting In case of mulching or rear dumping of grass always avoid removing a large quantity of grass Never cut more than one third the total grass height in a single passage Regulate the forward speed according to the lawn conditions and the amount of grass removed LAWN CARE RECOMENDATIONS Each type of grass has different features and may thus require different ways to care for the lawn always read the instructions on seed boxes for mowing height for the growth conditions in the work area Keep in mind that most grass is made up of a stem and one or more leaves If leaves are fully cut the lawn is damaged and growth is more difficult The following indications generally apply too low a cut causes grass tears and uprooting with a spot ted aspect in the summer cutting must be higher to avoid the ground from drying do not cut wet grass this could reduce blade efficiency due to sticky grass and tear the lawn for particularly high grass initially mow at maximum admit ted machine height followed by a second mow after two or three days The appearance of the lawn will improve cutting in both directions at the same height if you alternate the SU End of operations When the work has been completed release the brake lever 1 and disconnect the spark plug cap 2 WAIT UNTIL THE BLADE STOPS before performing any work 3 GRASS CUTTING I 4 ROUTINE MAINTENANCE NOTE This machine cuts lawns in various modes before starting work prepare the machine based on how the lawn is to be mowed MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF 3 1a Preparation for grass cutting and collection in grass catcher Lift the rear stone guard 1 and correctly hook on the grass catcher 2 as shown in the figure 3 1 b Preparation for grass cutting and rear discharge Remove the grass catcher and check that the guard 1 maintains its lowered position 24 rear stone IMPORTANT Regular careful keeping the safety level and machine unchanged in time Store the lawnmower in a dry place 1 maintenance is essential original performance of for the Wear strong working gloves during any cleaning mainte nance or adjustment operation on the machine 2 Carefully clean the machines with water after each cut remove the grass debris and mud accumulated inside the chassis to avoid their drying and thus making the next start up difficult 3 The paintwork on the inside of the chassis may peel off in time due to the abrasive action of the cut grass in this case intervene promptly by touching up the paintwork using a

Скачать

Случайные обсуждения

Ответы 0

Зазоры клапанов?

4 года назад

Ответы 0

Сколько времени может работать без перерыва?

7 лет назад

Ответы 1

Плавают обороты как регулировать карбюратор?