![Kramer FC-26 Руководства по эксплуатации онлайн [15/68] 139638](/img/pdf.png)
Kramer FC-26 Руководства по эксплуатации онлайн [15/68] 139638
![Kramer FC-26 Руководства по эксплуатации онлайн [15/68] 139638](/views2/1152649/page15/bgf.png)
10
Initial Configuration and Use Overview
To browse the FC-26 Web pages on taking the device out of the box, use the
default host name, (see Section 10).
To configure the FC-26:
1. Connect the Ethernet port on the rear panel of the FC-26 to a PC, either
directly or via a LAN, (see Section 6.1).
2. Using a Web browser and the relevant IP address, browse the General Info
home page (see Figure 11).
3. Click on Device Settings to browse to the Device Settings page, (see
Figure 13).
4. Enter the time and date manually, or enter the Time server address for
automatic time and date synchronization.
5. Click Save Changes.
6. Click on Communication to browse to the Communication page, (see
Figure 14).
7. Enter the IP address, mask and gateway for static IP addressing and Click
Set. We recommend that you set a meaningful host name.
Note: If you have changed the IP from the default setting, you must reload
the General Info home page again using the new IP address.
8. Click on Serial Ports Settings to browse to the Serial Port Settings page,
(see Figure 15).
9. Associate the required serial ports with their corresponding TCP/UDP
settings.
10. For each associated serial port, enter the serial port configuration
parameters using the drop-down lists under Serial Configuration.
11. Click Save Changes.
12. If required, click on Security to browse to the Security page.
Содержание
- User manual 1
- Contents 4
- Figures 4
- Introduction 6
- Achieving the best performance 7
- Getting started 7
- Safety instructions 7
- Recycling kramer products 8
- Overview 9
- About the power over ethernet feature 11
- Defining the fc 26 ethernet controller 12
- Figure 2 defines the front panel of the fc 26 12
- Figure 3 defines the rear panel of the fc 26 13
- Configuring the fc 26 ethernet controller 14
- Initial configuration and use overview 14
- Configuring a virtual port on the pc 16
- Setting up an ethernet connection on the pc 16
- Connecting the fc 26 17
- Connecting the ethernet port directly to a pc 18
- Connecting via ethernet 18
- Connecting the ethernet port via a network hub or switch 21
- Connecting to the fc 26 via rs 232 or ir 22
- Browsing the web pages 23
- Remote operation via the web pages 23
- Loading and saving configurations 24
- Connected clients page 25
- Device settings page 26
- Communication page 28
- Serial port settings page 29
- Ir command learner page 30
- Not available for normal operation 30
- Note while learning is in progress the four ir out leds light and the fc 26 is 30
- The ir command learner page allows you to teach the fc 26 ir commands 30
- These can be saved for later use 30
- On the security page click on 31
- Security page 31
- The confirmation popup is displayed as shown in figure 18 31
- The security page allows you to turn logon authentication on or off 31
- To activate web page security 31
- Valid user and password for default logon credentials see section 10 31
- When security is on access to the web pages is granted only on submission of a 31
- Logs page 33
- About us page 34
- Configuring and maintaining the fc 26 36
- Ir learning 36
- Resetting to the factory default settings 37
- Upgrading the firmware 37
- Technical specifications 38
- Data handling performance 39
- Example bandwidth calculation 39
- Default communication parameters 40
- Default logon authentication 40
- Ip address after performing a factory reset the dhcp and the ip address are set 40
- Note the fc 26 is dispatched from the factory with dhcp enabled and a random 40
- To the values shown below 40
- Command string 41
- Device long response 41
- Device message format 41
- Host message format 41
- Kramer protocol 3000 41
- Kramer protocol 3000 syntax 41
- Simple command 41
- Command terms 42
- Chaining commands 43
- Command forms 43
- Entering commands 43
- Maximum string length 43
- Kramer protocol 3000 command list 44
- Kramer protocol 3000 detailed commands 45
- This section lists the detailed commands applicable to the fc 26 45
- Ir status 66
- Ir transmit status 66
- Parameters 66
- Parity types 66
- Serial types 66
Похожие устройства
- Kramer FC-50 Руководства по эксплуатации
- Kramer VP-14 Руководства по эксплуатации
- Kramer VP-14xl Руководства по эксплуатации
- Kramer PL-50 Руководства по эксплуатации
- Kramer RB-6 Руководства по эксплуатации
- Kramer PL-15 Руководства по эксплуатации
- Kramer PT-4iREX Руководства по эксплуатации
- Kramer PT-5R/T Руководства по эксплуатации
- Kramer 401DN Руководства по эксплуатации
- Kramer 401C Руководства по эксплуатации
- Kramer VP-100 Руководства по эксплуатации
- Kramer 7408 Руководства по эксплуатации
- Ritmix RAT-310 Инструкция по эксплуатации
- Ritmix RAT-501 Инструкция по эксплуатации
- Ritmix RAT-201 Инструкция по эксплуатации
- Kramer 7508 Руководства по эксплуатации
- Kramer FC-7501 Руководства по эксплуатации
- Kramer FC-331 Руководства по эксплуатации
- Kramer FC-332 Руководства по эксплуатации
- Kramer FC-113 Руководства по эксплуатации