Hitachi DS18DBLTL [12/108] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi DS18DBLTL [12/108] English

Hitachi DS18DBLRJ [12/108] English
English
11
(2) Regarding the temperatures of the rechargeable
battery
The temperatures for rechargeable batteries are as
shown in Table 2, and batteries that have become
hot should be cooled for a while before being
recharged.
Table 2 Recharging ranges of batteries
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 3.
Table 3 Charging time (At 20°C)
NOTE:
The charging time may vary according to temperature
and power source voltage.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE:
After operation, pull out batteries from the charger
first, and then keep the batteries properly.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an extended
period is not activated, the electric discharge might
be low when using them the first and second time.
This is a temporary phenomenon, and normal time
required for recharging will be restored by recharging
the batteries 2 – 3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION:
When the battery charger has been continuosly used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
If the battery is recharged when it is warm due to
battery use or exposure to sunlight, the pilot lamp
map light in green.
The battery will not be recharged. In such a case, let
the battery cool before charging.
When the pilot lamp flickers in red (at 0.2-second
intervals), check for and take out any foreign objects
in the charger’s battery installation hole. If there are
no foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
PRIOR TO OPERATION
Setting up and checking the work environment
Check if the work environment is suitable by following
the precautions.
HOW TO USE
1. Confirm the clutch dial position (See Fig. 5)
The tightening torque of this unit can be adjusted
according to the clutch dial position, at which the
clutch dial is set.
(1) When using this unit as a screwdriver, line up the one
of the numbers “1, 3, 5 ... 22” on the clutch dial, or
the dots, with the triangle mark on the outer body.
(2) When using this unit as a drill, align the clutch dial
drill mark “
” with the triangle mark on the outer
body.
CAUTION:
The clutch dial cannot be set between the numerals
“1, 3, 5 ... 22” or the dots.
Do not use with the clutch dial numeral between
“22” and the line at the middle of the drill mark.
Doing so may cause damage. (See Fig. 6)
2. Tightening torque adjustment
(1) Tightening torque
Tightening torque should correspond in its intensity
to the screw diameter. When too strong torque is
used, the screw head may be broken or be injured.
Be sure to adjust the clutch dial position according to
the screw diameter.
(2) Tightening torque indication
The tightening torque differs depending on the type
of screw and the material being tightened.
The unit indicates the tightening torque with the
numbers “1, 3, 5 ... 22” on the clutch dial , and the
dots. The tightening toque at position “1” is the
weakest and the torque is strongest at the highest
number. (See Fig. 5)
(3) Adjusting the tightening torque
Rotate the clutch dial and line up the numbers “1, 3,
5, ... 22” on the clutch dial, or the dots, with the
triangle mark on the outer body. Adjust the clutch
dial in the weak or the strong torque direction
according to the torque you need.
CAUTION:
The motor rotation may be locked to cease while the
unit is used as drill. While operating the driver drill,
take care not to lock the motor.
Too long hammering may cause the screw broken
due to excessive tightening.
3. Change rotation speed
Operate the shift knob to change the rotational speed.
Move the shift knob in the direction of the arrow (See
Figs. 7 and 8).
Temperatures at
Rechargeable batteries
which the battery
can be recharged
BSL1430, BSL1830 0°C – 50°C
Charger
UC18YRSL
Battery
BSL1430, BSL1830 Approx. 45 min.
01Eng_DS14DBL_EE 09/7/2, 20:5811

Содержание

Похожие устройства

English 2 Regarding the temperatures of the rechargeable battery The temperatures for rechargeable batteries are as shown in Table 2 and batteries that have become hot should be cooled for a while before being recharged Table 2 Recharging ranges of batteries Temperatures at which the battery can be recharged Rechargeable batteries BSL1430 BSL1830 O O If the battery is recharged when it is warm due to battery use or exposure to sunlight the pilot lamp map light in green The battery will not be recharged In such a case let the battery cool before charging When the pilot lamp flickers in red at 0 2 second intervals check for and take out any foreign objects in the charger s battery installation hole If there are no foreign objects it is probable that the battery or charger is malfunctioning Take it to your authorized Service Center PRIOR TO OPERATION 0 C 50 C 3 Regarding recharging time Depending on the combination of the charger and batteries the charging time will become as shown in Table 3 O Setting up and checking the work environment Check if the work environment is suitable by following the precautions HOW TO USE Table 3 Charging time At 20 C Charger UC18YRSL Battery BSL1430 BSL1830 Approx 45 min NOTE The charging time may vary according to temperature and power source voltage 4 Disconnect the charger s power cord from the receptacle 5 Hold the charger firmly and pull out the battery NOTE After operation pull out batteries from the charger first and then keep the batteries properly Regarding electric batteries etc discharge in case of new As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated the electric discharge might be low when using them the first and second time This is a temporary phenomenon and normal time required for recharging will be restored by recharging the batteries 2 3 times How to make the batteries perform longer 1 Recharge the batteries before they become completely exhausted When you feel that the power of the tool becomes weaker stop using the tool and recharge its battery If you continue to use the tool and exhaust the electric current the battery may be damaged and its life will become shorter 2 Avoid recharging at high temperatures A rechargeable battery will be hot immediately after use If such a battery is recharged immediately after use its internal chemical substance will deteriorate and the battery life will be shortened Leave the battery and recharge it after it has cooled for a while CAUTION O When the battery charger has been continuosly used the battery charger will be heated thus constituting the cause of the failures Once the charging has been completed give 15 minutes rest until the next charging 11 1 Confirm the clutch dial position See Fig 5 The tightening torque of this unit can be adjusted according to the clutch dial position at which the clutch dial is set 1 When using this unit as a screwdriver line up the one of the numbers 1 3 5 22 on the clutch dial or the dots with the triangle mark on the outer body 2 When using this unit as a drill align the clutch dial drill mark with the triangle mark on the outer body CAUTION O The clutch dial cannot be set between the numerals 1 3 5 22 or the dots O Do not use with the clutch dial numeral between 22 and the line at the middle of the drill mark Doing so may cause damage See Fig 6 2 Tightening torque adjustment 1 Tightening torque Tightening torque should correspond in its intensity to the screw diameter When too strong torque is used the screw head may be broken or be injured Be sure to adjust the clutch dial position according to the screw diameter 2 Tightening torque indication The tightening torque differs depending on the type of screw and the material being tightened The unit indicates the tightening torque with the numbers 1 3 5 22 on the clutch dial and the dots The tightening toque at position 1 is the weakest and the torque is strongest at the highest number See Fig 5 3 Adjusting the tightening torque Rotate the clutch dial and line up the numbers 1 3 5 22 on the clutch dial or the dots with the triangle mark on the outer body Adjust the clutch dial in the weak or the strong torque direction according to the torque you need CAUTION O The motor rotation may be locked to cease while the unit is used as drill While operating the driver drill take care not to lock the motor O Too long hammering may cause the screw broken due to excessive tightening 3 Change rotation speed Operate the shift knob to change the rotational speed Move the shift knob in the direction of the arrow See Figs 7 and 8

Скачать