Home
Главная
Hitachi
Сетевой гайковерт
WR14VBNS
Инструкция по эксплуатации Страница: 8

Hitachi WR14VBNS [8/52] English

English

2. Do not touch the bumper or hammer case during

continuous operation

The bumper and hammer case become hot during

continuous screw tightening so be careful not to

touch them at that time.

3. Work at a tightening torque suitable for the bolt

under impact

The optimum tightening torque for nuts and bolts

differs with material and size of the nuts and bolts.

An excessively large tightening torque for a small

bolt may strech or break the bolt. The tightening

torque increases proportionally to the operating

time. Use the correct operating time for the bolt.

4. Selecting the socket to be matched to the bolt

Be sure to use a socket which is matched to the

bolt to be tightened. Using an improper socket will

result not only in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex or square-holed socket will

not give an adequate tightness for fitting to the nut

or anvil, consequently resulting in loss of tightening

torque.

Pay attention to wear of socket holes, and replace

before further wear develops. Matching socket and

bolt sizes are shown in Table 1.

The numerical value of a socket designation denotes

the side to side distance (S) of its hex hole.

5. Holding the tool

Hold the Impact Wrench firmly with both hands by

the body handle and the side handle. In this case

hold the wrench in line with the bolt.

It is not necessary to push the wrench very hard.

Hold the wrench with a force just sufficient to

counteract the impact force.

6. Confirm the tightening torque

The following factors contribute to a reduction of

the tightening torque. So confirm the actual

tightening torque needed by screwing up some

bolts before the job with a hand torque wrench.

Factors affecting the tightening torque are as follows.

(1) Line voltage:

The tightening torque decreases when the line

voltage becomes low (See Fig. 5).

(2) Operating time:

The tightening torque increases when the operating

time increases. But the tightening torque does not

increase above a certain value even if the tool is

driven for a long time (See Fig. 5).

(3) Diameter of bolt:

The tightening torque differs with the diameter of

the bolt as shown in Fig. 5. Generally a larger

diameter bolt has a larger tightening torque.

(4) Tightening conditions:

The tightening torque differs according to the torque

ratio; class, and length of bolts even when bolts with

the same size threads are used. The tightening torque

also differs according to the condition of the surface

of metal through which the bolts are to be tightened.

(5) Using optional parts:

The tightening torque is reduced a little when an

extension bar, universal joint or a long socket is used.

(6) Clearance of the socket:

A worn or deformed hex or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque.

Using an improper socket which does not match

to the bolt will result in an insufficient tightening

torque. Matching socket and bolt sizes are shown

in Table 1.

MAINTENANCE AND INSPECTION

1. Inspecting the socket

A worn or deformed hex or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque. Pay attention to wear of

socket holes periodically, and replace with a new

one if needed.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and replacement

on this tool should ONLY be performed by a Hitachi

Authorized Service Center.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool

must be returned to Hitachi Authorized Service

Center for the cord to be replaced.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

01Eng_WR14VB_EE 12/4/08, 11:527

Содержание

Похожие устройства

English 2 Do not touch the bumper or hammer case during continuous operation The bumper and hammer case become hot during continuous screw tightening so be careful not to touch them at that time 3 Work at a tightening torque suitable for the bolt under impact The optimum tightening torque for nuts and bolts differs with material and size of the nuts and bolts An excessively large tightening torque for a small bolt may strech or break the bolt The tightening torque increases proportionally to the operating time Use the correct operating time for the bolt 4 Selecting the socket to be matched to the bolt Be sure to use a socket which is matched to the bolt to be tightened Using an improper socket will result not only in insufficient tightening but also in damage to the socket or nut A worn or deformed hex or square holed socket will not give an adequate tightness for fitting to the nut or anvil consequently resulting in loss of tightening torque Pay attention to wear of socket holes and replace before further wear develops Matching socket and bolt sizes are shown in Table 1 The numerical value of a socket designation denotes the side to side distance S of its hex hole 5 Holding the tool Hold the Impact Wrench firmly with both hands by the body handle and the side handle In this case hold the wrench in line with the bolt It is not necessary to push the wrench very hard Hold the wrench with a force just sufficient to counteract the impact force 6 Confirm the tightening torque The following factors contribute to a reduction of the tightening torque So confirm the actual tightening torque needed by screwing up some bolts before the job with a hand torque wrench Factors affecting the tightening torque are as follows 1 Line voltage The tightening torque decreases when the line voltage becomes low See Fig 5 2 Operating time The tightening torque increases when the operating time increases But the tightening torque does not increase above a certain value even if the tool is driven for a long time See Fig 5 3 Diameter of bolt The tightening torque differs with the diameter of the bolt as shown in Fig 5 Generally a larger diameter bolt has a larger tightening torque 4 Tightening conditions The tightening torque differs according to the torque ratio class and length of bolts even when bolts with the same size threads are used The tightening torque also differs according to the condition of the surface of metal through which the bolts are to be tightened 5 Using optional parts The tightening torque is reduced a little when an extension bar universal joint or a long socket is used 6 Clearance of the socket A worn or deformed hex or a square holed socket will not give an adequate tightness to the fitting 7 between the nut or anvil consequently resulting in loss of tightening torque Using an improper socket which does not match to the bolt will result in an insufficient tightening torque Matching socket and bolt sizes are shown in Table 1 MAINTENANCE AND INSPECTION 1 Inspecting the socket A worn or deformed hex or a square holed socket will not give an adequate tightness to the fitting between the nut or anvil consequently resulting in loss of tightening torque Pay attention to wear of socket holes periodically and replace with a new one if needed 2 Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screws be loose retighten them immediately Failure to do so could result in serious hazard 3 Maintenance of the motor The motor unit winding is the very heart of the power tool Exercise due care to ensure the winding does not become damaged and or wet with oil or water 4 Inspecting the carbon brushes For your continued safety and electrical shock protection carbon brush inspection and replacement on this tool should ONLY be performed by a Hitachi Authorized Service Center 5 Replacing supply cord If the supply cord of Tool is damaged the Tool must be returned to Hitachi Authorized Service Center for the cord to be replaced 6 Service parts list A Item No B Code No C No Used D Remarks CAUTION Repair modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance In the operation and maintenance of power tools the safety regulations and standards prescribed in each country must be observed MODIFICATION Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements Accordingly some parts i e code numbers and or design may be changed without prior notice GUARANTEE We guarantee Hitachi Power Tools in accordance with statutory country specific regulation This guarantee does not cover defects or damage due to misuse abuse or normal wear and tear In case of complaint please send the Power Tool undismantled with the GUARANTEE CERTIFICATE found at the end of this Handling instruction to a Hitachi Authorized Service Center

Скачать