![GRAPHITE 59G086 Инструкция по эксплуатации онлайн [12/96] 320684](/img/pdf.png)
GRAPHITE 59G086 Инструкция по эксплуатации онлайн [12/96] 320684
![GRAPHITE 59G086 Инструкция по эксплуатации онлайн [12/96] 320684](/views2/1382127/page12/bgc.png)
12
the handle. A contact with the power mains network may transfer
voltage onto metal parts of the power tool, which may result in
electric shock.
• The power cord must be kept away from the rotating working
tools. When the control over the tool is lost, the power cord may
be cut or caught, and your hand or the entire arm may get into the
rotating working tool.
• Do not put the power tool aside, before the working tool
comes to complete stop. The rotating working tool may come in
contact with a surface, which it is put aside onto, and you may lose
control over the tool.
• Do not carry the power tool, which is in motion. An accidental
contact with the rotating working tool may caught in your clothes
and drill into an operator’s body.
• Clean ventilation slots of the power tool on a regular basis. The
motor blower sucks dust into the casing, while large accumulation of
metal dust may cause electric hazard.
• Do not use the power tool near ammable materials. Sparks
may cause ignition.
• Do not use tools, which require liquid cooling agents. The use
of water or other cooling agents may cause electric shocks.
Recoil and proper safety guidelines
• Recoil is a sudden reaction of the power tool to seizure or
blocking of a rotating working tool, such a grinding wheel, cut-
o wheel or a wire brush, etc.
The seizure and blocking may suddenly stop a rotating working
tool. The power tool without control will be jerked in the
opposite direction to the working tool.
When the grinding wheel stops or catches in the workpiece, an
edge od the grinding wheel immersed in the workpiece may
lock and cause recoil or rejection. The movement of the grinding
wheel (towards or away from the operator) depends on the
movement of the grinding wheel in a place, where it is locked.
The grinding wheels may also break.
Recoil is a consequence of incorrect operation of the power tool.
This can be avoided by observing the following precautions.
• The power tool must be held rmly, while your body and
hands should be positioned to alleviate recoil. If the additional
handle is included as standard equipment, it should be used
at all times to provide the highest control over recoil forces or
rejecting moment during start-up. An operator can take control
of recoil and jerking by taking proper precautions.
• Never hold your hands in the vicinity of rotating working
tools. A working tool may injure your hand as a result of recoil.
• Always keep your hands away from rotating working tools. As
a result of kick back, working tool may cause hand injury.
• Always stay away from the reach zone, in which the power tool
moves during recoil. As a result of recoil, the power tool moves in
the opposite direction to the movement of the grinding wheel, where
it locks.
• Corners, sharp edges, etc. should be worked with special
attention. Recoil or locking of the working tools should be
prevented. A rotating working tool is more prone to seizure, when
working angles, corners, sharp edges or when it is rebound. This may
result in loss of control or recoil.
• Do not use discs for wood or toothed discs. Working tools of this
type often cause recoil or loss of control over the working tool.
Special safety guidelines for grinding and cutting with the
grinding wheel.
• Always use the grinding wheel intended for a given power
tool and guard intended for a given grinding wheel. Grinding
wheel that are not part of equipment of a given power tool may be
insuciently covered or safe.
• Oset grinding wheels should be fastened so that their
grinding surface does not protrude beyond the protective
guard. Incorrectly seated grinding wheel and protruding beyond the
edge of the protective guard may not be suciently covered.
• The guard must be secured to the power tool to ensure the
highest possible safety level and positioned so that the
uncovered part of the grinding wheel facing the operator is
as small as possible. The guard protects the operator against chips,
accidental contact with the grinding wheel and sparks, which may
set clothing on re.
• Grinding wheels can only be used according to its purpose.
• The side surface of the grinding wheel should not be used
for cutting. Cut-o grinding wheels are designed for removal of
material with the disc edge. The inuence of lateral forces on the
grinding wheels may break them.
• Undamaged fastening anges of a correct size and shape
should always be used for a selected grinding wheel. Proper
anges support the grinding wheel and reduce the risk of its breaking.
Flanges for cut-o wheels may dier from anges designed for other
grinding wheels.
• Do not use worn grinding wheels from larger power tools.
Grinding wheels for larger power tools are not designed for higher
rotational speed, which is specic to smaller power tools. Thus, such
grinding wheels may break.
Additional specic safety guidelines for cutting with a cut-o wheel
• Always prevent a cut-o wheel from seizure and avoid
excessive pressure. Do not make too deep cuts. The overload of
a cut-o wheel increases its load and tendency for seizure or locking,
and thus may result in recoil or breaking of a cut-o wheel.
• Avoid areas in front of and behind a rotating cut-o wheel.
When a cut-o wheel is moved onto a workpiece away from the
operator, it may cause the power tool to kick back as a result of recoil,
with a rotating cut-o wheel pointing directly towards the operator.
• When a cut-o wheel seizes or you take a break from work,
switch o the power tool and wait until it comes to a complete
stop. Do not attempt to remove a rotating cut-o wheel from
a cutting place, since it may cause recoil. Find and eliminate a
cause of seizure.
• Do not switch the power tool back on, if it is still sunk in a
workpiece. Before you continue to cut, a cut-o wheel must
reach its full rotational speed. Otherwise, a cut-o wheel may
catch, spring back from a workpiece and cause recoil.
• Boards and large objects should be supported to reduce the
risk of recoil caused by a seized cut-o wheel. Large objects may
bend under their own weight. A workpiece should be supported from
both sides, both near the cut line and its edge.
• Special caution should be exercised, when holes are cut
in a wall or in conned spaces. As a cut-o wheel sinks into a
workpiece, it may cause the power tool to recoil, when it encounters a
gas or water supply line, power conductors or other objects.
Specic safety guidelines for sanding with sandpaper
• Do not use too large sheets of sandpaper. Always follow
guidelines of a manufacturer, when the size of a sandpaper is
selected. Sandpaper protruding beyond a grinding disc may cause
injuries and result in locking and tearing of sandpaper, or recoil.
Specic safety guidelines for working with wire brushes
• It should always be remembered that pieces of wire are lost
even during normal use. Do not overload wires by putting
excessive pressure. Airborne pieces of wire may easily puncture
thin clothing and/or skin.
• If a guard is recommended to be used, prevent a brush from
touching the guard. A brush diameter for plates and pots may
increase due to the pressure and centrifugal forces.
Additional safety guidelines
• Before connecting to the power source, always make sure the
supply voltage is compatible with the value specied on the
nameplate of the tool.
• Before the grinder is connected, always check the power
cord. In case of damage, have it repaired in an authorised
workshop.
• Before all installation works, the plug should be taken out of
the receptacle.
• Grinding tools should be checked before each use. A grinding
tool must be correctly fastened and should rotate freely. As
part of the test, the tool should be switched on with no load
for at least one minute in a safe position. Do not use damaged
or vibrating grinding tools. Grinding tools should be round.
Damaged grinding tools may break and cause injuries.
• Once a grinding tool is installed and before the grinder is
switched on, check the grinding tool for correct installation
and free rotations, and whether it does not catch the guard.
• The spindle lock button can be activated, only when the
grinder spindle does not move.
Содержание
- Instrukcja oryginalna obsługi szlifierka kątowa 59g086 6
- Szczegółowe przepisy bezpieczeństwa 6
- 2 3 4 5 8
- Przygotowanie do pracy 8
- Obsługa i konserwacja 9
- Praca ustawienia 9
- Deklaracja zgodności we 10
- Ec declaration of conformity megfelelési nyilatkozat ek 10
- Ochrona środowiska ce 10
- Parametry techniczne 10
- Detailed safety regulations 11
- Gwarancja i serwis 11
- Translation of the original instructions angle grinder 59g086 11
- 2 3 4 5 13
- Preparation for work 13
- Operation adjustments 14
- Operation and maintenance 14
- Detaillierte sicherheitsvorschriften 15
- Environmental protection 15
- Specifications 15
- Übersetzung der originalbetriebsanleitung winkelschleifer 59g086 15
- 2 3 4 5 17
- Betrieb einstellungen 18
- Vorbereitung auf den einsatz 18
- Bedienung und wartung 19
- Technische parameter 19
- Umweltschutz 20
- Перевод оригинальной инструкции по эксплуатации угловая шлифовальная машина 59g086 20
- Правила техники безопасности 20
- 2 3 4 5 22
- Подготовка к работе 23
- Работа настройка 23
- Технические характеристики 24
- Техническое обслуживание 24
- Защита окружающей среды 25
- Переклад інструкції з оригіналу машина шліфувальна кутова болгарка 59g086 25
- Правила техніки безпеки під час користування устаткуванням 25
- 2 3 4 5 27
- Порядок роботи робочі налаштування 28
- Підготовка до роботи 28
- Зберігання та обслуговування 29
- Технічні характеристики 29
- Eredeti használati utasítás fordítása sarokcsiszoló 59g086 30
- Részletes biztonsági előírások 30
- Охорона середовища 30
- 2 3 4 5 32
- Felkészítés az üzembehelyezésre 32
- Kezelése és karbantartása 33
- Munkavégzés beállítások 33
- Környezetvédelem 34
- Műszaki jellemzők 34
- Prevederi speciale pentru securitate 34
- Traducere a instrucțiunilor originale polizor unghiular 59g086 34
- 2 3 4 5 36
- Lucrul asamblarea 37
- Pregătirea pentru lucru 37
- Deservirea întreţinerea 38
- Parametrii tehnici 38
- Protecţia mediului 38
- Podrobné bezpečnostní pokyny 39
- Překlad původního návodu k používání úhlová bruska 59g086 39
- 2 3 4 5 40
- Provoz nastavení 41
- Příprava k práci 41
- Péče a údržba 42
- Technické parametry 42
- Detailné bezpečnostné predpisy 43
- Ochrana životního prostředí 43
- Preklad pôvodného návodu na použitie uhlová brúska 59g086 43
- 2 3 4 5 45
- Pred uvedením do prevádzky 45
- Ošetrovanie a údržba 46
- Práca nastavenia 46
- Ochrana životného prostredia 47
- Prevod izvirnih navodil kotni brusilnik 59g086 47
- Specifični varnostni predpisi 47
- Technické parametre 47
- 2 3 4 5 49
- Priprava na uporabo 49
- Uporaba nastavitve 50
- Vzdrževanje in hramba 50
- Detalios saugos taisyklės 51
- Originalios instrukcijos vertimas kampinis šlifuoklis 59g086 51
- Tehnični parametri 51
- Varovanje okolja 51
- 2 3 4 5 53
- Pasiruošimas darbui 53
- Darbas ir reguliavimas 54
- Aplinkos apsauga ir 55
- Aptarnavimas ir priežiūra 55
- Detalizētie drošības noteikumi 55
- Instrukciju tulkojums no oriģinālvalodas leņķa slīpmašīna 59g086 55
- Techniniai duomenys 55
- 2 3 4 5 57
- Darbs iestatījumi 58
- Sagatavošanās darbam 58
- Algupärase kasutusjuhendi tõlge nurklihvija 59g086 59
- Apkalpošana un apkope 59
- Eriohutusjuhised 59
- Tehniskie parametri 59
- Vides aizsardzība ce 59
- 2 3 4 5 61
- Ettevalmistus tööks 62
- Töö seadistamine 62
- Hooldus ja hoidmine 63
- Keskkonnakaitse 63
- Tehnilised parameetrid 63
- Подробни правила за безопасност 63
- Превод на оригиналната инструкция ъглова шлайфмашина 59g086 63
- 2 3 4 5 66
- Подготовка за работа 66
- Работа настройки 67
- Detaljni propisi o sigurnosti 68
- Prijevod originalnih uputa kutna brusilica 59g086 68
- Обслужване и поддръжка 68
- Опазване на околната среда 68
- Технически параметри 68
- 2 3 4 5 70
- Priprema za rad 71
- Rad postavke 71
- Opšte mere bezbednosti 72
- Prevod orginalnog uputstva ugaona brusilica 59g086 72
- Rukovanje i održavanje 72
- Tehnički parametri 72
- Zaštita okoliša 72
- 2 3 4 5 74
- Priprema za rad 75
- Rad postavke 75
- Korišćenje i održavanje 76
- Tehničke karakteristike 76
- Zaštita sredine 76
- Κανονεσ ασφαλειασ 77
- Μεταφραση του πρωτοτυπου των οδηγιων χρησησ γωνιακο τριβειο 59g086 77
- 2 3 4 5 79
- Λειτουργια ρυθμιση 80
- Προετοιμασια για εργασια 80
- Τεχνικα χαρακτηριστικα 81
- Τεχνικη συντηρηση 81
- Normas de seguridad detalladas 82
- Traducción del manual original amoladora angular 59g086 82
- Προστασια περιβαλλοντοσ 82
- 2 3 4 5 84
- Preparación para trabajar 84
- Trabajo ajustes 85
- Uso y mantenimiento 85
- Norme particolari di sicurezza 86
- Parametros técnicos 86
- Protección medioambiental 86
- Traduzione delle istruzioni originali smerigliatrice angolare 59g086 86
- 2 3 4 5 88
- Funzionamento regolazione 89
- Preparazione al funzionamento 89
- Parametri tecnici 90
- Servizio e manutenzione 90
- Gedetailleerde veiligheidsvoorschriften 91
- Protezione dell ambiente 91
- Vertaling van originele gebruiksaanwijzing haakse slijper 59g086 91
- 2 3 4 5 93
- Werkvoorbereiding 93
- Werk instellingen 94
- Bediening en onderhoud 95
- Milieubescherming 95
- Technische parameters 95
Похожие устройства
- GRAPHITE 59G220 Инструкция по эксплуатации
- GRAPHITE 59G717 Инструкция по эксплуатации
- GRAPHITE 58G950 Инструкция по эксплуатации
- GRAPHITE 58G943 Инструкция по эксплуатации
- GRAPHITE 58G602 Инструкция по эксплуатации
- GRAPHITE 58G601 Инструкция по эксплуатации
- GRAPHITE 58G726 Инструкция по эксплуатации
- GRAPHITE 58G722 Инструкция по эксплуатации
- GRAPHITE 58G718 Инструкция по эксплуатации
- GRAPHITE 58G716 Инструкция по эксплуатации
- GRAPHITE 58G735 Инструкция по эксплуатации
- GRAPHITE 58G738 Инструкция по эксплуатации
- GRAPHITE 58G727 Инструкция по эксплуатации
- GRAPHITE 58G717 Инструкция по эксплуатации
- GRAPHITE 58G788 Инструкция по эксплуатации
- GRAPHITE 58G014 Инструкция по эксплуатации
- GRAPHITE 59G770 Инструкция по эксплуатации
- Metalac DIRECT G 100 Инструкция по эксплуатации
- Metalac DIRECT G 120 Инструкция по эксплуатации
- Metalac DIRECT G 150 Инструкция по эксплуатации