![Verto 51G075 Инструкция по эксплуатации онлайн [12/108] 461396](/img/pdf.png)
Verto 51G075 Инструкция по эксплуатации онлайн [12/108] 461396
![Verto 51G075 Инструкция по эксплуатации онлайн [12/108] 461396](/views2/1569830/page12/bgc.png)
12
handle. A contact with the power mains network may transfer voltage
onto metal parts of the power tool, which may result in electric shock.
• The power cord must be kept away from the rotating working
tools. When the control over the tool is lost, the power cord may be cut
or caught, and your hand or the entire arm may get into the rotating
working tool.
• Do not put the power tool aside, before the working tool comes
to complete stop. The rotating working tool may come in contact
with a surface, which it is put aside onto, and you may lose control over
the tool.
• Do not carry the power tool, which is in motion. An accidental
contact with the rotating working tool may caught in your clothes and
drill into an operator’s body.
• Clean ventilation slots of the power tool on a regular basis. The
motor blower sucks dust into the casing, while large accumulation of
metal dust may cause electric hazard.
• Do not use the power tool near ammable materials. Sparks may
cause ignition.
• Do not use tools, which require liquid cooling agents. The use of
water or other cooling agents may cause electric shocks.
Recoil and proper safety guidelines
• Recoil is a sudden reaction of the power tool to seizure or blocking
of a rotating working tool, such a grinding wheel, cut-off wheel or
a wire brush, etc.
The seizure and blocking may suddenly stop a rotating working
tool. The power tool without control will be jerked in the opposite
direction to the working tool.
When the grinding wheel stops or catches in the workpiece, an
edge od the grinding wheel immersed in the workpiece may lock
and cause recoil or rejection. The movement of the grinding wheel
(towards or away from the operator) depends on the movement
of the grinding wheel in a place, where it is locked. The grinding
wheels may also break.
Recoil is a consequence of incorrect operation of the power tool.
This can be avoided by observing the following precautions.
• The power tool must be held rmly, while your body and hands
should be positioned to alleviate recoil. If the additional handle
is included as standard equipment, it should be used at all times
to provide the highest control over recoil forces or rejecting
moment during start-up. An operator can take control of recoil and
jerking by taking proper precautions.
• Never hold your hands in the vicinity of rotating working tools.
A working tool may injure your hand as a result of recoil.
• Always stay away from the reach zone, in which the power tool
moves during recoil. As a result of recoil, the power tool moves in
the opposite direction to the movement of the grinding wheel, where
it locks.
• Corners, sharp edges, etc. should be worked with special attention.
Recoil or locking of the working tools should be prevented.
A rotating working tool is more prone to seizure, when working angles,
corners, sharp edges or when it is rebound. This may result in loss of
control or recoil.
• Do not use discs for wood or toothed discs. Working tools of this
type often cause recoil or loss of control over the working tool.
Special safety guidelines for grinding and cutting with the
grinding wheel.
• Always use the grinding wheel intended for a given power
tool and guard intended for a given grinding wheel. Grinding
wheel that are not part of equipment of a given power tool may be
insuciently covered or safe.
• Oset grinding wheels should be fastened so that their
grinding surface does not protrude beyond the protective
guard. Incorrectly seated grinding wheel and protruding beyond the
edge of the protective guard may not be suciently covered.
• The guard must be secured to the power tool to ensure the
highest possible safety level and positioned so that the
uncovered part of the grinding wheel facing the operator is
as small as possible. The guard protects the operator against chips,
accidental contact with the grinding wheel and sparks, which may set
clothing on re.
• Grinding wheels can only be used according to its purpose.
• The side surface of the grinding wheel should not be used for
cutting. Cut-o grinding wheels are designed for removal of material
with the disc edge. The inuence of lateral forces on the grinding
wheels may break them.
• Undamaged fastening anges of a correct size and shape
should always be used for a selected grinding wheel. Proper
anges support the grinding wheel and reduce the risk of its breaking.
Flanges for cut-o wheels may dier from anges designed for other
grinding wheels.
• Do not use worn grinding wheels from larger power tools.
Grinding wheels for larger power tools are not designed for higher
rotational speed, which is specic to smaller power tools. Thus, such
grinding wheels may break.
Additional specic safety guidelines for cutting with a cut-o
wheel
• Always prevent a cut-o wheel from seizure and avoid excessive
pressure. Do not make too deep cuts. The overload of a cut-o
wheel increases its load and tendency for seizure or locking, and thus
may result in recoil or breaking of a cut-o wheel.
• Avoid areas in front of and behind a rotating cut-o wheel.
When a cut-o wheel is moved onto a workpiece away from the
operator, it may cause the power tool to kick back as a result of recoil,
with a rotating cut-o wheel pointing directly towards the operator.
• When a cut-o wheel seizes or you take a break from work,
switch o the power tool and wait until it comes to a complete
stop. Do not attempt to remove a rotating cut-o wheel from a
cutting place, since it may cause recoil. Find and eliminate a cause
of seizure.
• Do not switch the power tool back on, if it is still sunk in a
workpiece. Before you continue to cut, a cut-o wheel must
reach its full rotational speed. Otherwise, a cut-o wheel may
catch, spring back from a workpiece and cause recoil.
• Boards and large objects should be supported to reduce the
risk of recoil caused by a seized cut-o wheel. Large objects may
bend under their own weight. A workpiece should be supported from
both sides, both near the cut line and its edge.
• Special caution should be exercised, when holes are cut in a
wall or in conned spaces. As a cut-o wheel sinks into a workpiece,
it may cause the power tool to recoil, when it encounters a gas or water
supply line, power conductors or other objects.
Specic safety guidelines for sanding with sandpaper
• Do not use too large sheets of sandpaper. Always follow
guidelines of a manufacturer, when the size of a sandpaper is
selected. Sandpaper protruding beyond a grinding disc may cause
injuries and result in locking and tearing of sandpaper, or recoil.
Specic safety guidelines for working with wire brushes
• It should always be remembered that pieces of wire are lost
even during normal use. Do not overload wires by putting
excessive pressure. Airborne pieces of wire may easily puncture thin
clothing and/or skin.
• If a guard is recommended to be used, prevent a brush from
touching the guard. A brush diameter for plates and pots may
increase due to the pressure and centrifugal forces.
Additional safety guidelines
• Before connecting to the power source, always make sure the
supply voltage is compatible with the value specied on the
nameplate of the tool.
• Before the grinder is connected, always check the power cord.
In case of damage, have it repaired in an authorised workshop.
• Before all installation works, the plug should be taken out of
the receptacle.
• Grinding tools should be checked before each use. A grinding
tool must be correctly fastened and should rotate freely. As
part of the test, the tool should be switched on with no load
for at least one minute in a safe position. Do not use damaged
or vibrating grinding tools. Grinding tools should be round.
Damaged grinding tools may break and cause injuries.
• Once a grinding tool is installed and before the grinder is
switched on, check the grinding tool for correct installation and
free rotations, and whether it does not catch the guard.
• The spindle lock button can be activated, only when the grinder
spindle does not move.
Содержание
- A kątowa 1
- Amoladora angular 1
- Angle grinder 1
- Brusilica kutna 1
- Brusilica ugaona 1
- Bruska úhlová 1
- Brúska uhlová 1
- Haakse slijper 1
- Hleifer 1
- Kampinis šlifuoklis 1
- Kotni brusilnik 1
- Leņķa slīpmašīna 1
- Maşină unghiulară de şlefuit 1
- Nurklihvija 1
- Sarokcsiszoló 1
- Smerigliatrice angolare 1
- Szlifierka kątowa 1
- Winkelschleifer 1
- Γωνιακοσ τροχοσ 1
- Машина шлифовальная угловая 1
- Шинка наріжна 1
- Шлифовальная угловая 1
- Шліфмашинка наріжна 1
- Ъглошлайф 1
- Instrukcja oryginalna obsługi 5
- Szczegółowe przepisy bezpieczeństwa 5
- Szlifierka kątowa 51g075 5
- Przygotowanie do pracy 7
- Praca ustawienia 8
- Obsługa i konserwacja 9
- Parametry techniczne 9
- Ochrona środowiska ce 10
- Angle grinder 51g075 11
- Detailed safety regulations 11
- Gwarancja i serwis 11
- Translation of the original instruction 11
- Preparation for work 13
- Operation adjustments 14
- Operation and maintenance 15
- Specifications 15
- Detaillierte sicherheitsvorschriften 16
- Environmental protection ce 16
- Winkelschleifer 51g075 16
- Übersetzung der originalbetriebsanleitung 16
- Vorbereitung auf den einsatz 18
- Betrieb einstellungen 19
- Bedienung und wartung 20
- Technische parameter 20
- Umweltschutz ce 21
- Машина шлифовальная угловая 51g075 21
- Перевод оригинальной инструкции по эксплуатации 21
- Правила техники безопасности 21
- Подготовка к работе 24
- Работа настройка 25
- Технические характеристики 26
- Техническое обслуживание 26
- Защита окружающей среды 27
- Информация о дате изготовления указана в серийном номере который находится на изделии 27
- Машина шліфувальна кутова болгарка 51g075 27
- Переклад інструкції з польського оригіналу 27
- Правила техніки безпеки під час користування устаткуванням 27
- Підготовка до роботи 29
- Порядок роботи робочі налаштування 30
- Зберігання та обслуговування 31
- Az eredeti használati utasítás fordítása 32
- Részletes biztonsági előírások 32
- Sarokcsiszoló 51g075 32
- Охорона середовища се 32
- Технічні характеристики 32
- Felkészítés az üzembehelyezésre 35
- Munkavégzés beállítások 35
- Kezelése és karbantartása 36
- Környezetvédelem ce 37
- Műszaki jellemzők 37
- Polizor unghiular 51g075 37
- Prevederi speciale pentru securitate 37
- Traducerea instructiunilor originale 37
- Lucrul asamblarea 40
- Pregătirea pentru lucru 40
- Deservirea întreţinerea 41
- Parametrii tehnici 42
- Podrobné bezpečnostní pokyny 42
- Protecţia mediului ce 42
- Překlad původního návodu k používání 42
- Úhlová bruska 51g075 42
- Příprava k práci 44
- Provoz nastavení 45
- Péče a údržba 46
- Technické parametry 46
- Detailné bezpečnostné predpisy 47
- Ochrana životního prostředí ce 47
- Preklad pôvodného návodu na použitie 47
- Uhlová brúska 51g075 47
- Pred uvedením do prevádzky 49
- Práca nastavenia 50
- Ošetrovanie a údržba 51
- Technické parametre 51
- Kotni brusilnik 51g075 52
- Ochrana životného prostredia ce 52
- Prevod izvirnih navodil 52
- Specifični varnostni predpisi 52
- Priprava na uporabo 54
- Uporaba nastavitve 55
- Tehnični parametri 56
- Varovanje okolja ce 56
- Vzdrževanje in hramba 56
- Detalios saugos taisyklės 57
- Kampinis šlifuoklis 51g075 57
- Originalios instrukcijos vertimas 57
- Darbas ir reguliavimas 59
- Pasiruošimas darbui 59
- Aptarnavimas ir priežiūra 60
- Aplinkos apsauga ir ce 61
- Detalizētie drošības noteikumi 61
- Instrukcijas tulkojums no oriģinālvalodas 61
- Leņķa slīpmašīna 51g075 61
- Techniniai duomenys 61
- Darbs iestatījumi 64
- Sagatavošanās darbam 64
- Apkalpošana un apkope 65
- Tehniskie parametri 65
- Eriohutusjuhised 66
- Nurklihvija 51g075 66
- Originaalkasutusjuhendi tõlge 66
- Vides aizsardzība ce 66
- Ettevalmistus tööks 68
- Töö seadistamine 69
- Hooldus ja hoidmine 70
- Tehnilised parameetrid 70
- Keskkonnakaitse ce 71
- Подробни правила за безопасност 71
- Превод на оригиналната инструкция 71
- Ъглова шлайфмашина 51g075 71
- Подготовка за работа 74
- Работа настройки 74
- Обслужване и поддръжка 75
- Detaljni propisi o sigurnosti 76
- Kutna brusilica 51g075 76
- Prijevod originalnih uputa 76
- Опазване на околната среда ce 76
- Технически параметри 76
- Priprema za rad 79
- Rad postavke 79
- Rukovanje i održavanje 80
- Opšte mere bezbednosti 81
- Prevod originalnog uputstva 81
- Tehnički parametri 81
- Ugaona brusilica 51g075 81
- Zaštita okoliša ce 81
- Priprema za rad 83
- Rad postavke 84
- Korišćenje i održavanje 85
- Tehničke karakteristike 85
- Zaštita sredine ce 86
- Γωνιακο τριβειο 51g075 86
- Κανονεσ ασφαλειασ 86
- Μεταφραση των πρωτοτυπων οδηγιων χρησησ 86
- Λειτουργια ρυθμιση 89
- Προετοιμασια για εργασια 89
- Τεχνικη συντηρηση 90
- Προστασια περιβαλλοντοσ 91
- Τεχνικα χαρακτηριστικα 91
- Amoladora angular 51g075 92
- Normas de seguridad detalladas 92
- Traducción del manual original 92
- Preparación para trabajar 94
- Trabajo ajustes 95
- Parametros técnicos 96
- Protección medioambiental ce 96
- Uso y mantenimiento 96
- Norme particolari di sicurezza 97
- Smerigliatrice angolare 51g075 97
- Traduzione delle istruzioni originali 97
- Preparazione al funzionamento 99
- Funzionamento regolazione 100
- Parametri tecnici 101
- Servizio e manutenzione 101
- Gedetailleerde veiligheidsvoorschriften 102
- Haakse slijper 51g075 102
- Protezione dell ambiente ce 102
- Vertaling van originele gebruiksaanwijzing 102
- Werkvoorbereiding 104
- Werk instellingen 105
- Bediening en onderhoud 106
- Technische parameters 106
- 6 134 m 107
- 87 6 db a k 3 db a akoestische kracht niveau l 107
- 98 6 db a k 3 db a waarde van de trillingen versnelling 107
- Akoestische druk niveau l 107
- K 1 5 m 107
- Milieubescherming ce 107
- Om de blootstelling aan trillingen goed te schatten neem de periodes van uitzetten van het elektrogereedschap of de periodes van het aanzetten zonder gebruik in acht op die manier kan de totale blootstelling aan trillingen aanzienlijk lager zijn voer de extra veiligheidsmaatregelen in om de gebruiker tegen de risico s van trillingen te beschermen zoals onderhoud van het elektrogereedschap en werkstukken verzekering van de juiste temperatuur van de handen juiste organisatie van het werk 107
Похожие устройства
- Verto 50G529 Инструкция по эксплуатации
- Verto 50G527 Инструкция по эксплуатации
- Verto 50G137 Инструкция по эксплуатации
- Verto 52G506 Инструкция по эксплуатации
- Verto 52G505 Инструкция по эксплуатации
- Verto 52G555 Инструкция по эксплуатации
- Verto 52G400 Инструкция по эксплуатации
- Verto 52G568 Инструкция по эксплуатации
- Verto 52G567 Инструкция по эксплуатации
- Verto 52G500 Инструкция по эксплуатации
- Verto 52G584 Инструкция по эксплуатации
- Verto 52G684 Инструкция по эксплуатации
- Verto 52G682 Инструкция по эксплуатации
- Verto 52G549 Инструкция по эксплуатации
- Verto 52G548 Инструкция по эксплуатации
- Verto 52G547 Инструкция по эксплуатации
- Verto 52G449 Инструкция по эксплуатации
- Verto 52G441 Инструкция по эксплуатации
- Verto 52G590 Инструкция по эксплуатации
- Verto 52G300 Инструкция по эксплуатации