![Verto 51G075 [15/108] Operation and maintenance](/img/pdf.png)
Verto 51G075 [15/108] Operation and maintenance
![Verto 51G075 [15/108] Operation and maintenance](/views2/1569830/page15/bgf.png)
15
Cut-o wheels reach high temperatures during operation. It
cannot be touched with uncovered body parts, before they cool
down.
GRINDING
Grinding wheel, cup-type grinding wheels, flap wheels, wheels with
abrasive fibre, wire brushes and flexible discs, etc. should be used for
grinding. Each type of discs and workpiece requires proper working
method and personal protective equipment.
Cut-o wheels should not be used for grinding.
Grinding discs are intended for removal of material with an edge
of the disc.
• Do not use the lateral surface for grinding. The optimum
working angle for this disc type is 30° (g. H).
• Works related to grinding can be performed only, when proper
grinding discs are used for a given workpiece.
When ap wheels, discs with abrasive bre and exible discs for
sandpaper are used, attention should be paid to the proper tool
angle (g. I).
• Do not grind with the entire surface of a wheel.
• This disc type should be used for working at surfaces.
Wire brushes are mainly used for cleaning sections and hard-to-
reach spaces. They can be used to remove rust, painting coats, etc.
from a workpiece surface (g. K).
Only such working tools can be used, whose permissible
rotational speed is higher or equal to the maximum no load speed
of the grinder.
OPERATION AND MAINTENANCE
Before any operations related to installation, adjustment, repairs
or maintenance are commenced, the plug of the power cord
should be disconnected from the socket.
MAINTENANCE AND STORAGE
• It is recommended to clean the tool after each use.
• Do not use water or other fluids for cleaning.
• The tool should be cleaned with a dry piece of cloth or blown with
compressed air of low pressure.
• Do not use any cleaning agents or solvents, since they may damage
plastic parts.
• Venting slots in the motor housing should be cleaned on a regular
basis not to overload the tool.
• When the power cord is damaged, it should be replaced with
the power cord of the same parameters. It should be performed
by a qualified professional or the tool should be delivered to an
authorised service shop.
• When the commutator sparks excessively, have the condition of
motor carbon brushes checked by a qualified person.
• The tool should be always stored in a dry place and out of reach
of children.
REPLACING THE CARBON BRUSHES
Worn (shorter than 5 mm), burnt or cracked motor carbon brushes
should be immediately replaced. Both carbon brushes should be
always replaced at the same time.
• Remove the covers of the carbon brushes (7) (g. E).
• Remove the worn carbon brushes.
• Remove any carbon dust using compressed air.
• Insert new carbon brushes (g. F) (brushes should easily slide into
the brush holders).
• Fasten the covers of the carbon brushes (7).
After the carbon brushes are replaced, switch on the grinder with
no load and wait for 1-2 minutes to make the carbon brushes t
the motor commutator. Carbon brushes should be replaced by a
qualied person using original spare parts only.
All types of faults and defects should be eliminated by an authorised
service of the manufacturer.
SPECIFICATIONS
RAT ED DATA
Angle Grinder
Parameter Value
Power supply voltage 230 V AC
Power supply frequency 50 Hz
Rated power 750 W
Rated rotational speed 12000 min
-1
Max. grinding wheel diameter 125 mm
Inner disc diameter 22,2 mm
Spindle thread M14
Protection class II
Weight 1,86 kg
Year of manufacture 2016
NOISE AND VIBRATION DATA
Information regarding noise and vibration
The following levels of emitted noise, such as emitted acoustic
pressure Lp
A
and acoustic power level Lw
A
and measurement
uncertainty K have been given in the instruction manual as defined
in the EN 60745 standard.
The following vibration value (acceleration value) a
h
and measurement
uncertainty K have been determined as defined in the EN 60745
standard.
The vibration level provided in this instruction manual have been
determined according to the measurement procedure as defined
in the EN 60745 standard and can be used for comparison of power
tools. This can be used for preliminary assessment of exposure to
vibrations.
The provided vibration level is representative for main applications
of the power tool. If the power tool is used for other applications or
with other working tools, and if it is not sufficiently maintained, the
vibration level may vary. The aforementioned reasons may increase
the exposure to vibrations during the entire operating period.
In order to precisely estimate the exposure to vibrations, periods
should be accounted for, in which the power tool is switched off, or
when it is switched on, but not operated. Thus, the total exposure to
vibration may prove considerably lower.
Additional safety measures should be taken to protect the user
against effects of vibrations, such as: maintenance of the power tool
Содержание
- A kątowa 1
- Amoladora angular 1
- Angle grinder 1
- Brusilica kutna 1
- Brusilica ugaona 1
- Bruska úhlová 1
- Brúska uhlová 1
- Haakse slijper 1
- Hleifer 1
- Kampinis šlifuoklis 1
- Kotni brusilnik 1
- Leņķa slīpmašīna 1
- Maşină unghiulară de şlefuit 1
- Nurklihvija 1
- Sarokcsiszoló 1
- Smerigliatrice angolare 1
- Szlifierka kątowa 1
- Winkelschleifer 1
- Γωνιακοσ τροχοσ 1
- Машина шлифовальная угловая 1
- Шинка наріжна 1
- Шлифовальная угловая 1
- Шліфмашинка наріжна 1
- Ъглошлайф 1
- Instrukcja oryginalna obsługi 5
- Szczegółowe przepisy bezpieczeństwa 5
- Szlifierka kątowa 51g075 5
- Przygotowanie do pracy 7
- Praca ustawienia 8
- Obsługa i konserwacja 9
- Parametry techniczne 9
- Ochrona środowiska ce 10
- Angle grinder 51g075 11
- Detailed safety regulations 11
- Gwarancja i serwis 11
- Translation of the original instruction 11
- Preparation for work 13
- Operation adjustments 14
- Operation and maintenance 15
- Specifications 15
- Detaillierte sicherheitsvorschriften 16
- Environmental protection ce 16
- Winkelschleifer 51g075 16
- Übersetzung der originalbetriebsanleitung 16
- Vorbereitung auf den einsatz 18
- Betrieb einstellungen 19
- Bedienung und wartung 20
- Technische parameter 20
- Umweltschutz ce 21
- Машина шлифовальная угловая 51g075 21
- Перевод оригинальной инструкции по эксплуатации 21
- Правила техники безопасности 21
- Подготовка к работе 24
- Работа настройка 25
- Технические характеристики 26
- Техническое обслуживание 26
- Защита окружающей среды 27
- Информация о дате изготовления указана в серийном номере который находится на изделии 27
- Машина шліфувальна кутова болгарка 51g075 27
- Переклад інструкції з польського оригіналу 27
- Правила техніки безпеки під час користування устаткуванням 27
- Підготовка до роботи 29
- Порядок роботи робочі налаштування 30
- Зберігання та обслуговування 31
- Az eredeti használati utasítás fordítása 32
- Részletes biztonsági előírások 32
- Sarokcsiszoló 51g075 32
- Охорона середовища се 32
- Технічні характеристики 32
- Felkészítés az üzembehelyezésre 35
- Munkavégzés beállítások 35
- Kezelése és karbantartása 36
- Környezetvédelem ce 37
- Műszaki jellemzők 37
- Polizor unghiular 51g075 37
- Prevederi speciale pentru securitate 37
- Traducerea instructiunilor originale 37
- Lucrul asamblarea 40
- Pregătirea pentru lucru 40
- Deservirea întreţinerea 41
- Parametrii tehnici 42
- Podrobné bezpečnostní pokyny 42
- Protecţia mediului ce 42
- Překlad původního návodu k používání 42
- Úhlová bruska 51g075 42
- Příprava k práci 44
- Provoz nastavení 45
- Péče a údržba 46
- Technické parametry 46
- Detailné bezpečnostné predpisy 47
- Ochrana životního prostředí ce 47
- Preklad pôvodného návodu na použitie 47
- Uhlová brúska 51g075 47
- Pred uvedením do prevádzky 49
- Práca nastavenia 50
- Ošetrovanie a údržba 51
- Technické parametre 51
- Kotni brusilnik 51g075 52
- Ochrana životného prostredia ce 52
- Prevod izvirnih navodil 52
- Specifični varnostni predpisi 52
- Priprava na uporabo 54
- Uporaba nastavitve 55
- Tehnični parametri 56
- Varovanje okolja ce 56
- Vzdrževanje in hramba 56
- Detalios saugos taisyklės 57
- Kampinis šlifuoklis 51g075 57
- Originalios instrukcijos vertimas 57
- Darbas ir reguliavimas 59
- Pasiruošimas darbui 59
- Aptarnavimas ir priežiūra 60
- Aplinkos apsauga ir ce 61
- Detalizētie drošības noteikumi 61
- Instrukcijas tulkojums no oriģinālvalodas 61
- Leņķa slīpmašīna 51g075 61
- Techniniai duomenys 61
- Darbs iestatījumi 64
- Sagatavošanās darbam 64
- Apkalpošana un apkope 65
- Tehniskie parametri 65
- Eriohutusjuhised 66
- Nurklihvija 51g075 66
- Originaalkasutusjuhendi tõlge 66
- Vides aizsardzība ce 66
- Ettevalmistus tööks 68
- Töö seadistamine 69
- Hooldus ja hoidmine 70
- Tehnilised parameetrid 70
- Keskkonnakaitse ce 71
- Подробни правила за безопасност 71
- Превод на оригиналната инструкция 71
- Ъглова шлайфмашина 51g075 71
- Подготовка за работа 74
- Работа настройки 74
- Обслужване и поддръжка 75
- Detaljni propisi o sigurnosti 76
- Kutna brusilica 51g075 76
- Prijevod originalnih uputa 76
- Опазване на околната среда ce 76
- Технически параметри 76
- Priprema za rad 79
- Rad postavke 79
- Rukovanje i održavanje 80
- Opšte mere bezbednosti 81
- Prevod originalnog uputstva 81
- Tehnički parametri 81
- Ugaona brusilica 51g075 81
- Zaštita okoliša ce 81
- Priprema za rad 83
- Rad postavke 84
- Korišćenje i održavanje 85
- Tehničke karakteristike 85
- Zaštita sredine ce 86
- Γωνιακο τριβειο 51g075 86
- Κανονεσ ασφαλειασ 86
- Μεταφραση των πρωτοτυπων οδηγιων χρησησ 86
- Λειτουργια ρυθμιση 89
- Προετοιμασια για εργασια 89
- Τεχνικη συντηρηση 90
- Προστασια περιβαλλοντοσ 91
- Τεχνικα χαρακτηριστικα 91
- Amoladora angular 51g075 92
- Normas de seguridad detalladas 92
- Traducción del manual original 92
- Preparación para trabajar 94
- Trabajo ajustes 95
- Parametros técnicos 96
- Protección medioambiental ce 96
- Uso y mantenimiento 96
- Norme particolari di sicurezza 97
- Smerigliatrice angolare 51g075 97
- Traduzione delle istruzioni originali 97
- Preparazione al funzionamento 99
- Funzionamento regolazione 100
- Parametri tecnici 101
- Servizio e manutenzione 101
- Gedetailleerde veiligheidsvoorschriften 102
- Haakse slijper 51g075 102
- Protezione dell ambiente ce 102
- Vertaling van originele gebruiksaanwijzing 102
- Werkvoorbereiding 104
- Werk instellingen 105
- Bediening en onderhoud 106
- Technische parameters 106
- 6 134 m 107
- 87 6 db a k 3 db a akoestische kracht niveau l 107
- 98 6 db a k 3 db a waarde van de trillingen versnelling 107
- Akoestische druk niveau l 107
- K 1 5 m 107
- Milieubescherming ce 107
- Om de blootstelling aan trillingen goed te schatten neem de periodes van uitzetten van het elektrogereedschap of de periodes van het aanzetten zonder gebruik in acht op die manier kan de totale blootstelling aan trillingen aanzienlijk lager zijn voer de extra veiligheidsmaatregelen in om de gebruiker tegen de risico s van trillingen te beschermen zoals onderhoud van het elektrogereedschap en werkstukken verzekering van de juiste temperatuur van de handen juiste organisatie van het werk 107
Похожие устройства
- Verto 50G529 Инструкция по эксплуатации
- Verto 50G527 Инструкция по эксплуатации
- Verto 50G137 Инструкция по эксплуатации
- Verto 52G506 Инструкция по эксплуатации
- Verto 52G505 Инструкция по эксплуатации
- Verto 52G555 Инструкция по эксплуатации
- Verto 52G400 Инструкция по эксплуатации
- Verto 52G568 Инструкция по эксплуатации
- Verto 52G567 Инструкция по эксплуатации
- Verto 52G500 Инструкция по эксплуатации
- Verto 52G584 Инструкция по эксплуатации
- Verto 52G684 Инструкция по эксплуатации
- Verto 52G682 Инструкция по эксплуатации
- Verto 52G549 Инструкция по эксплуатации
- Verto 52G548 Инструкция по эксплуатации
- Verto 52G547 Инструкция по эксплуатации
- Verto 52G449 Инструкция по эксплуатации
- Verto 52G441 Инструкция по эксплуатации
- Verto 52G590 Инструкция по эксплуатации
- Verto 52G300 Инструкция по эксплуатации