Daikin FTKE35BVM [146/268] Accessories
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Daikin FTKE35BVM [146/268] Accessories

Daikin CDX25AVMA [146/268] Accessories
ED12-321A Indoor Units
Installation Manual 141
4
2. Indoor Units
2.1 Wall Mounted Type FTK(X)E 25/35 B
A
Mounting plate
1
C
Air purifying filter
1
D
Wireless remote controller
1
E
Remote controller holder
1
G
AAA dry-cell batteries
2
H
Indoor unit fixing screws
M4 X 12L
2
K
Operation manual
1
2
L
Installation manuals
1
M
Photocatalytic deodorizing filter
B
Mounting plate fixing
screws M4 X 25L
6
F
Fixing screws for remote controller
holder
M3 X 20L
2
J
Insulation tape
1
Accessories
1.
Indoor unit
• The indoor unit should be sited in a place where:
1) the restrictions on installation specified in the indoor unit installation drawings are met,
2) both air intake and exhaust have clear paths met,
3) the unit is not in the path of direct sunlight,
4) the unit is away from the source of heat or steam,
5) there is no source of machine oil vapour (this may shorten indoor unit life),
6) cool air is circulated throughout the room,
7) the unit is away from electronic ignition type fluorescent lamps (inverter or rapid start type) as they may shorten the
remote control range,
8)
the unit is at least 1 metre away from any television or radio set (unit may cause interference with the picture or sound).
2.
Wireless Remote Controller
1) Turn on all the fluorescent lamps in the room, if any, and find the site where remote control signals are properly
received by the indoor unit (within 7 metres).
• Before choosing the installation site, obtain user approval.
Choosing a Site
Installation Tips
1. How to remove the front grille.
1) Hold the grille by the tabs on the two sides and lift it until it stops with a click.
2)
Supporting the front grille with one hand, release the lock by sliding down the knob with the other hand.
3) To remove the front grille, pull it toward yourself with both hands.
2. How to attach the front grille.
1) Set the 3 keys of the front grille into the slots and push them in all the way.
2) Supporting the front grille with one hand, fit the lock by sliding up the knob with the other hand.
3) Close the front grille slowly in this state. (Push the grille at the 3 points, two at both sides and in
the middle.)
3. How to remove the front panel.
1) Open the front grille.
2) Remove the screws (2 pcs) on the front panel.
3) Pull the lower part of the front panel toward you, then remove the front panel completely.
(There are 2 hooks on the upper part.)
If it is difficult to remove, open the front grille and raise the top grid, using a
screwdriver, to unhook the hooks.
4. How to attach the front panel.
1)
Attach the front panel to the front grille, and lock the upper hooks (2 points) securely.
2) Tighten the screws (2) on the front panel.
3) Close the front grille.
5. How to set the different addresses.
1) When two indoor units are installed in one room, the two
wireless remote controllers can be set for different addresses.
6. PCB in the indoor unit
1) Remove the front panel.
2) Remove the sensor parts cover (2-screws), then
remove the electric parts box (1-screw).
3) Slide the metallic cover to remove it. (4-claws on the
electric parts box.)
4) Cut the jumper JA on PCB.
7. Wireless remote controller
1) Cut the jumper J4.
Upper grille
Hook
Screwdriver
Filter guide
Raise and
remove
Upper hook
Screwdriver
Wireless
remote
controller
AddressJ4
CUT
EXIST
1
2
JA
ADDRESS
J4
ADDRESS:
CUT
EXIST
1
2
JA
JB
JC
Metallic cover
Sensor
parts cover
PCB
Electric
parts box
Claws (4 points)
Slide up the knob.
Fit the key
into the slot.

Содержание

Похожие устройства

Скачать