![Citizen CL-E720DT Command Reference DMX онлайн [113/154] 632093](/img/pdf.png)
Citizen CL-E720DT Command Reference DMX онлайн [113/154] 632093
![Citizen CL-E720DT Command Reference DMX онлайн [113/154] 632093](/views2/1842788/page113/bg71.png)
1-112
File format parameter
Model selection method <1|2>
None --- When specifying a bar code other than W1D
1 --- Model 1
2 --- Model 2
Error correction level <H|Q|M|L>
H ---- Ultra high reliability level （Level H）
Q ---- High reliability level （Level Q）
M ---- Standard level （Level M）
L ---- High density level （Level L）
Mask number <0〜7,8>
None --- Automatic selection
0 to 7 --- Mask 0 to7
8 --- No mask
Data input mode <A|M>
A ---- Automatic setting (Default)
Data character string（JIS 8 bit characters, Shift
JIS）
M ---- Manual setting
Character mode <N|A|B|K>
N --- Number
A --- Alphanumeric characters（Default）
B --- Binary
K --- Chinese characters
Data character string
Binary mode --- Amount of data＋Data
（ The data amount is 2 bytes and
expressed using BCD codes）
Other modes --- Data
Содержание
- Citizen cl e cl s and clp range command reference manual version ii 1
- Chapter 1 2
- Command interpreter command interpreter and command system 2
- Outline 3
- Outline of command system 3
- Fig 1 command summary 4
- Stx l e with printing 4
- X without printing x without printing 4
- Outline of interpreter 5
- Outline of label format data 6
- Outline of label printing method 8
- Control code specification 9
- System level immediate execution commands 10
- Command reset 11
- Printer status transmission request 8 byte packet 11
- Printer status 12
- Soh command shutdown 12
- Stop cancel 12
- Printer status transmission request 1 byte packet 13
- Transmission of number of remaining sheets to be issued 13
- Caution 14
- Code 01 i 14
- Error status transmission request 4 byte packet 14
- Function after receiving this command printer sends 4 byte data on current conditions inside the printer to the host pc shown below are contents of the 4 byte data to be sent from the printer 14
- The 0d hex code is added to the end of transmission data 14
- System level occasional execution commands 15
- Setting date and time 17
- Setting feedback character transmission validness 17
- Date and time transmission request 18
- Setting paper length for continuous paper 19
- Setting two page edit mode double buffer 20
- Changing number of prints for edited format 21
- Abcdefg 22
- Label one sheet feed 22
- Setting edge sensor selection 22
- Caution if value out of range is specified the command parameter will be ignored 23
- Code 02 f nnn 23
- Function with the setting above the distance between paper sensor and cutter or peeler can be specified 23
- If optional functions such as cutter peeler and ejection are turned on from the control panel their initialization values will be set automatically these initialization values however vary depending on the specifications of each option for details see the instruction manuals of each option 23
- Nnn 3 digit data initial value and its set range vary depending on the command setting 23
- Once this command was set auto setting function is stopped due to priority for user s specification do not set this command if not necessary 23
- Setting 23
- Setting peeling cutting position 23
- Units 0 1 inch 0 mm 23
- When nnn is appropriate the label is fed the required amount then cut at the paper gap 23
- When nnn is large the amount of feed is large so the next printing label will be cut 23
- When nnn is small the amount of feed is small so printed label will be cut 23
- Cutter 24
- Paper sensor print head 24
- Peeler 24
- Printing edited or formerly printed format 24
- Graphics data block input command 25
- Bit image data uses ascii format data in this example 7 bit image data with the file name of mark7 is stored in the memory card and printed out value of inside is shown in hex format 26
- Bit image loading file format 26
- Bit image data uses ascii format data in this example 8 bit image data with the file name of mark8 is stored in the memory card and printed out value of inside is shown in hex format note data below is described in hex 27
- Bit image format 27
- Download of truetype font 28
- Pause per label printing 29
- Extension system command printer settings 30
- Setting peeling cutting position 31
- Setting y code transmission to serial port request 31
- Specifying printing contents setting start 32
- Setting maximum label length 33
- Changing units from inch to metric system 34
- Changing units from metric to inch system 34
- Caution if value less than 0 inch 0050 is specified the initialization value will be set automatically with the initialization value set printing starts from the bottom of the label if the command is used after completing printing this command setting will not be effective to the first sheet of the label from the second sheet of the label this will be effective 35
- Code 02 o nnnn 35
- Cutter peeler print head reference point 35
- Figure 35
- Function specifies the distance between paper sensor and print head by changing this value a physical printing start position can be changed 35
- Onnnn 0110 printing area 35
- Onnnn 1 0 inch initialization value 35
- Peeling 35
- Printing area onnnn 0080 35
- Printing area onnnn 0120 35
- Reference point 35
- Setting nnnn 4 digit data initial value and its set range vary depending on the command set 35
- Setting printing position 35
- Units 0 1 inch or 0 mm 35
- Dump list 36
- Paper cut 36
- Setting dump mode start 36
- Pause in occasional execution 37
- Allocation of modules varies with command settings refer to the table below 38
- Caution clearing of on board flash memory module takes about 10 seconds for models with lcd on line appears on the lcd as soon as the module contents are cleared 38
- Clearing memory module contents 38
- Code 02 q n 38
- Function clears all data in memory module 38
- Input data 02 q b sets clearance of module b on board sd ram contents 38
- Setting n memory module specification parameter 38
- Setting reflective paper sensor selection 39
- Setting paper feed speed 40
- Printing quality test pattern 41
- Setting one page edit mode single buffer 41
- Rewriting specified format register contents 42
- Printer version number transmission request 43
- Setting memory switch contents 43
- Information in memory module transmission request 44
- Testing flash memory 44
- Default module selection 45
- Clearing memory module contents in file units 46
- Caution it depends on each truetype font file for the symbol set which becomes actually effective 47
- Code 02 ysxx 47
- Example pc 850 multilingual is chosen 47
- Function selection of a truetype font symbol set 47
- Input data 02 yspm 47
- Refer to the following table for a setting value refer to the following table for a setting value 47
- Setting s s fixed 47
- The character sequence of 2 figures the character sequence of 2 figures 47
- Truetype font symbol set selection 47
- Xx specification of a symbol set 47
- Printing printer status 48
- Select command set 48
- Head disconnection detection 49
- Setting printing method 49
- Setting ejection tear off 50
- Setting label width 51
- Label format commands 52
- Set format attribute 54
- 567894 55
- Setting offset in direction of column 55
- Nd sheet 56
- Rd sheet 56
- Setting number of cuts 2 digit 56
- St sheet 56
- Th sheet 56
- Setting pixel size in horizontal and vertical direction 57
- Completion of setting printing contents field preparation and printing labels 58
- Entering previous defined field character string into global table 58
- Setting print density head heat factor 58
- Changing units from inch to metric system 59
- Changing units from metric to inch system 59
- Setting printable area speed 60
- Setting backfeed speed 61
- Specifying space between characters 62
- Setting number of prints 63
- Setting offset in direction of row 64
- Calling label format 65
- Printer 65
- Setting unprintable area speed 66
- Aa a maximum 8 characters of format name ending with cr code 67
- Caution this command is used differently depending on the command set in other words it is used differently depending on whether the command is designated at the end of the label format or designated at a given position within the label format when designating it at a given position within the label format label format ending command e or x is required 67
- Code s naa aa 67
- D11 sets pixel size 67
- Example input data below represents that label format data is stored in the on board memory by using format name name 67
- Function stores label format into memory module and ends label format 67
- Input data 02 n sets units to inch 67
- L starts label format mode 67
- Printer sets data printer with smooth font 24pt 67
- Refer to the table below for details 67
- Saname stores label format name name in on board ram and ends label format mode 67
- Setting n memory module specification parameter a b c d e f g allocation of module varies with command settings refer to the table below 67
- Storing label format 67
- Specifying ending code 68
- Completion of setting printing contents field preparation 69
- Setting previous field to character string replacement mode field 69
- Setting slash zero 70
- Truetype font symbol set selection 70
- Setting addition of previous defined printing contents field data 1 71
- Setting subtraction of previous defined printing contents field data 1 72
- Setting addition of previous defined printing contents field data 2 73
- Setting subtraction of previous defined printing contents field data 2 74
- Setting number of prints for same label 75
- Setting number of cuts 4 digit 76
- Character field definition 77
- Horizontal h 78
- Table 1 a 203 dpi print head 78
- Table 1 b 300 dpi print head 78
- Vertical v 78
- Table 2 79
- Type font character field definition 80
- Bar code field definition 81
- Table 3 82
- Ruled line definition 83
- Box definition 84
- Graphics printing definition 85
- Polygon definition 86
- Circle definition 88
- Reading out from global register 89
- Date and time printing definition 90
- Chapter 2 92
- Fonts and bar fonts and bar codes 92
- Description of fonts 93
- Description of bar codes 99
- Control characters are coded into code subset a see the control characters are coded into code subset a see the character input reference table below 102
- Control code 102
- Example the test bar code is first printed with code subset b and then 123 bar code with code subset a data is transmitted in the order of b test 2 character f and 123 102
- Input code btest f123 102
- End code 114
- In the case of bound function 114
- Chapter 3 118
- Overlay function overlay function 118
- Memory assignment will be specified by each emulation as follows 119
- Note factory default can be changed by the command when a memory assignment parameter n that is not specified n a in the above list is selected the memory c is automatically selected 119
- Outline 119
- This printer once stores the required images ruled lines and character strings in the on board memory or optional memory module then overlays the data onto the printing data 119
- Type of memory 119
- Storage and readout commands 120
- Type of graphic image data 121
- Font downloading commands 122
- Font downloading commands are used to transmit the user specified font bit map font to the on board memory or memory module the transmission of the downloading font data is in conformity with the hp standard esc sequence 122
- Chapter 4 123
- Printing command printing command examples 123
- Column address 124
- Origin 124
- Printing position specification 124
- Row address 124
- 1 1 000 0400 0800 ab 125
- Character printing 125
- Ruled line printing 126
- Bar code printing 127
- Program description 127
- When bar codes are to be printed attribute data such as printing position and bar code types must be included in the command 127
- Command outline is as follows 129
- Increasing and decreasing number printing 129
- Nn prints same number nn times and advances to the next counter 129
- Note p value is zero fill character note p value is zero fill character 129
- Pii ii base 36 system ii value from 0 to z is added 129
- Pii ii base 36 system ii value from 0 to z is subtracted 129
- Pii ii decimal ii value is added 129
- Pii ii decimal ii value is subtracted 129
- When continuously increasing and decreasing numbers like serial numbers are to be printed on labels continuous printing can be performed automatically by the counter in the printer at this time the number of steps for increasing and decreasing addition and subtraction width and number of prints of the same label can be set 129
- 100 100 100 130
- 94 103 10f 130
- 96 103 10a 130
- 98 100 105 130
- Fig fig fig fig 130
- Sample printing 131
- Chapter 5 132
- Interface functions interface functions 132
- Rs 232c serial interface 133
- C communication control flowchart 135
- The following is a reference flowchart for sending and receiving data the following is a reference flowchart for sending and receiving data by using printer transmission request command 01 a or 01 f in xon xoff protocol and compatible machine on mode 135
- Parallel interface 137
- Appendixes 139
- A feedback character transmission validness 140
- A setting date and time transmission 140
- Appendix 1 list of commands 140
- B date and time transmission request 140
- Cnnnn setting continuous paper length 140
- D setting 2 page edit mode double buffer 140
- E selecting edge sensor for paper position detection 140
- Ennnn setting number of printing sheets for edited format 140
- Error status transmission request 4 byte 140
- F label one sheet feed 140
- Fnnn setting paper position setting when cutting and peeling 140
- G printing edited format 140
- Imfaa writing graphic data 140
- Imtnn truetype fonts downloading command 140
- J setting pause per each label printing 140
- Kdabc printer settings 140
- N a not supported command n a not supported command 140
- Y supported command 140
- Clearing memory module contents in file units 141
- Information in memory module transmission request 141
- Packing memory module contents 141
- Select command set 141
- Selecting default module a b 141
- Sensor level issued to port 141
- Setting memory switch contents 141
- Setting printing method 141
- Test print for printer status 141
- Testing flash memory 141
- Truetype fonts symbol set selection 141
- Version number transmission request 141
- Appendix 2 list of font character codes 146
- System font 1 6 146
- System font 7 ocr a 146
- Expansion font cg triumvirate cg triumvirate bold smooth font 147
- System font 8 ocr b 147
- Appendix 3 printing edit function 148
- Area sizes such as each buffer and register vary by model 149
- For details refer to appendix 6 list of specifications by model 149
- Module allocations vary depending on the command set 149
- This module allocation is for dm4 dm8 149
- Appendix 4 specification of switching of control codes 152
- Control codes can be switched from the menu on the operation panel by setting to alt mode the system level command start code soh immediate execution command and stx sequential execution command will be changed to the commands in the table below when setting alt mode replace the standard codes in the table below of this command reference with the corresponding codes in alt mode 152
- Appendix 5 specification list of command set 153
- Table below are items whose specifications will be changed using the switching function of the emulation command sets 153
- Appendix 6 list of specifications by model 154
- Table below are specifications required when editing printing for each model such as memory size and the maximum page length 154
Похожие устройства
- Citizen CL-E720DT Руководство по эксплуатации
- Катюша M151 Краткое руководство
- Катюша M151 Руководство по эксплуатации
- Катюша M151 Техническое описание
- Aviline DVR-B Инструкция по эксплуатации
- Aviline DVR-С Инструкция по эксплуатации
- Aviline CANA-400 Инструкция по эксплуатации
- Aviline CANA-800 Инструкция по эксплуатации
- Aviline CANA-PRO Инструкция по эксплуатации
- Aviline SmartAssist-335 Инструкция по эксплуатации
- Ballu machine BMFL-180M Инструкция по эксплуатации
- Ballu machine BMFL-270M Инструкция по эксплуатации
- Ballu machine BMFL-360M Инструкция по эксплуатации
- Ballu machine BMFL-450M Инструкция по эксплуатации
- Ballu machine BMFL-540M Инструкция по эксплуатации
- Ballu machine BMFL-720M Инструкция по эксплуатации
- Daichi AIR25AVQS1R/AIR25FVS1R Инструкция по монтажу и эксплуатации
- Daichi AIR35AVQS1R/AIR35FVS1R Инструкция по монтажу и эксплуатации
- Daichi AIR50AVQS1R/AIR50FVS1R Инструкция по монтажу и эксплуатации
- Daichi AIR60AVQS1R/AIR60FVS1R Инструкция по монтажу и эксплуатации