Home
Главная
Citizen
Термопринтер
CL-E720DT
Command Reference DMX Страница: 119

Citizen CL-E720DT [119/154] Outline

1-118

3.1 Outline

This printer once stores the required images, ruled lines and character

strings in the on-board memory or optional memory module, then

overlays the data onto the printing data.

3.2 Type of Memory

Memory assignment will be specified by each emulation as follows.

Command Set

Allocation of

module

DMI / DMW DM4 / DM8 DPP

on-board

SD-RAM

D A B

on-board flash

memor

G B A

PCMCIA Card

(

tion

)

E or F E or F E or F

Current

memory

module

on-board

SD-RAM

on-board

SD-RAM

on-board

SD-RAM

Note: Factory Default (*) can be changed by the command. When a memory

assignment parameter (n) that is not specified (N/A) in the above list is

selected, the memory C is automatically selected.

Содержание

Citizen cl e cl s and clp range command reference manual version ii 1
Chapter 1 2
Command interpreter command interpreter and command system 2
Outline 3
Outline of command system 3
Fig 1 command summary 4
Stx l e with printing 4
X without printing x without printing 4
Outline of interpreter 5
Outline of label format data 6
Outline of label printing method 8
Control code specification 9
System level immediate execution commands 10
Command reset 11
Printer status transmission request 8 byte packet 11
Printer status 12
Soh command shutdown 12
Stop cancel 12
Printer status transmission request 1 byte packet 13
Transmission of number of remaining sheets to be issued 13
Caution 14
Code 01 i 14
Error status transmission request 4 byte packet 14
Function after receiving this command printer sends 4 byte data on current conditions inside the printer to the host pc shown below are contents of the 4 byte data to be sent from the printer 14
The 0d hex code is added to the end of transmission data 14
System level occasional execution commands 15
Setting date and time 17
Setting feedback character transmission validness 17
Date and time transmission request 18
Setting paper length for continuous paper 19
Setting two page edit mode double buffer 20
Changing number of prints for edited format 21
Abcdefg 22
Label one sheet feed 22
Setting edge sensor selection 22
Caution if value out of range is specified the command parameter will be ignored 23
Code 02 f nnn 23
Function with the setting above the distance between paper sensor and cutter or peeler can be specified 23
If optional functions such as cutter peeler and ejection are turned on from the control panel their initialization values will be set automatically these initialization values however vary depending on the specifications of each option for details see the instruction manuals of each option 23
Nnn 3 digit data initial value and its set range vary depending on the command setting 23
Once this command was set auto setting function is stopped due to priority for user s specification do not set this command if not necessary 23
Setting 23
Setting peeling cutting position 23
Units 0 1 inch 0 mm 23
When nnn is appropriate the label is fed the required amount then cut at the paper gap 23
When nnn is large the amount of feed is large so the next printing label will be cut 23
When nnn is small the amount of feed is small so printed label will be cut 23
Cutter 24
Paper sensor print head 24
Peeler 24
Printing edited or formerly printed format 24
Graphics data block input command 25
Bit image data uses ascii format data in this example 7 bit image data with the file name of mark7 is stored in the memory card and printed out value of inside is shown in hex format 26
Bit image loading file format 26
Bit image data uses ascii format data in this example 8 bit image data with the file name of mark8 is stored in the memory card and printed out value of inside is shown in hex format note data below is described in hex 27
Bit image format 27
Download of truetype font 28
Pause per label printing 29
Extension system command printer settings 30
Setting peeling cutting position 31
Setting y code transmission to serial port request 31
Specifying printing contents setting start 32
Setting maximum label length 33
Changing units from inch to metric system 34
Changing units from metric to inch system 34
Caution if value less than 0 inch 0050 is specified the initialization value will be set automatically with the initialization value set printing starts from the bottom of the label if the command is used after completing printing this command setting will not be effective to the first sheet of the label from the second sheet of the label this will be effective 35
Code 02 o nnnn 35
Cutter peeler print head reference point 35
Figure 35
Function specifies the distance between paper sensor and print head by changing this value a physical printing start position can be changed 35
Onnnn 0110 printing area 35
Onnnn 1 0 inch initialization value 35
Peeling 35
Printing area onnnn 0080 35
Printing area onnnn 0120 35
Reference point 35
Setting nnnn 4 digit data initial value and its set range vary depending on the command set 35
Setting printing position 35
Units 0 1 inch or 0 mm 35
Dump list 36
Paper cut 36
Setting dump mode start 36
Pause in occasional execution 37
Allocation of modules varies with command settings refer to the table below 38
Caution clearing of on board flash memory module takes about 10 seconds for models with lcd on line appears on the lcd as soon as the module contents are cleared 38
Clearing memory module contents 38
Code 02 q n 38
Function clears all data in memory module 38
Input data 02 q b sets clearance of module b on board sd ram contents 38
Setting n memory module specification parameter 38
Setting reflective paper sensor selection 39
Setting paper feed speed 40
Printing quality test pattern 41
Setting one page edit mode single buffer 41
Rewriting specified format register contents 42
Printer version number transmission request 43
Setting memory switch contents 43
Information in memory module transmission request 44
Testing flash memory 44
Default module selection 45
Clearing memory module contents in file units 46
Caution it depends on each truetype font file for the symbol set which becomes actually effective 47
Code 02 ysxx 47
Example pc 850 multilingual is chosen 47
Function selection of a truetype font symbol set 47
Input data 02 yspm 47
Refer to the following table for a setting value refer to the following table for a setting value 47
Setting s s fixed 47
The character sequence of 2 figures the character sequence of 2 figures 47
Truetype font symbol set selection 47
Xx specification of a symbol set 47
Printing printer status 48
Select command set 48
Head disconnection detection 49
Setting printing method 49
Setting ejection tear off 50
Setting label width 51
Label format commands 52
Set format attribute 54
567894 55
Setting offset in direction of column 55
Nd sheet 56
Rd sheet 56
Setting number of cuts 2 digit 56
St sheet 56
Th sheet 56
Setting pixel size in horizontal and vertical direction 57
Completion of setting printing contents field preparation and printing labels 58
Entering previous defined field character string into global table 58
Setting print density head heat factor 58
Changing units from inch to metric system 59
Changing units from metric to inch system 59
Setting printable area speed 60
Setting backfeed speed 61
Specifying space between characters 62
Setting number of prints 63
Setting offset in direction of row 64
Calling label format 65
Printer 65
Setting unprintable area speed 66
Aa a maximum 8 characters of format name ending with cr code 67
Caution this command is used differently depending on the command set in other words it is used differently depending on whether the command is designated at the end of the label format or designated at a given position within the label format when designating it at a given position within the label format label format ending command e or x is required 67
Code s naa aa 67
D11 sets pixel size 67
Example input data below represents that label format data is stored in the on board memory by using format name name 67
Function stores label format into memory module and ends label format 67
Input data 02 n sets units to inch 67
L starts label format mode 67
Printer sets data printer with smooth font 24pt 67
Refer to the table below for details 67
Saname stores label format name name in on board ram and ends label format mode 67
Setting n memory module specification parameter a b c d e f g allocation of module varies with command settings refer to the table below 67
Storing label format 67
Specifying ending code 68
Completion of setting printing contents field preparation 69
Setting previous field to character string replacement mode field 69
Setting slash zero 70
Truetype font symbol set selection 70
Setting addition of previous defined printing contents field data 1 71
Setting subtraction of previous defined printing contents field data 1 72
Setting addition of previous defined printing contents field data 2 73
Setting subtraction of previous defined printing contents field data 2 74
Setting number of prints for same label 75
Setting number of cuts 4 digit 76
Character field definition 77
Horizontal h 78
Table 1 a 203 dpi print head 78
Table 1 b 300 dpi print head 78
Vertical v 78
Table 2 79
Type font character field definition 80
Bar code field definition 81
Table 3 82
Ruled line definition 83
Box definition 84
Graphics printing definition 85
Polygon definition 86
Circle definition 88
Reading out from global register 89
Date and time printing definition 90
Chapter 2 92
Fonts and bar fonts and bar codes 92
Description of fonts 93
Description of bar codes 99
Control characters are coded into code subset a see the control characters are coded into code subset a see the character input reference table below 102
Control code 102
Example the test bar code is first printed with code subset b and then 123 bar code with code subset a data is transmitted in the order of b test 2 character f and 123 102
Input code btest f123 102
End code 114
In the case of bound function 114
Chapter 3 118
Overlay function overlay function 118
Memory assignment will be specified by each emulation as follows 119
Note factory default can be changed by the command when a memory assignment parameter n that is not specified n a in the above list is selected the memory c is automatically selected 119
Outline 119
This printer once stores the required images ruled lines and character strings in the on board memory or optional memory module then overlays the data onto the printing data 119
Type of memory 119
Storage and readout commands 120
Type of graphic image data 121
Font downloading commands 122
Font downloading commands are used to transmit the user specified font bit map font to the on board memory or memory module the transmission of the downloading font data is in conformity with the hp standard esc sequence 122
Chapter 4 123
Printing command printing command examples 123
Column address 124
Origin 124
Printing position specification 124
Row address 124
1 1 000 0400 0800 ab 125
Character printing 125
Ruled line printing 126
Bar code printing 127
Program description 127
When bar codes are to be printed attribute data such as printing position and bar code types must be included in the command 127
Command outline is as follows 129
Increasing and decreasing number printing 129
Nn prints same number nn times and advances to the next counter 129
Note p value is zero fill character note p value is zero fill character 129
Pii ii base 36 system ii value from 0 to z is added 129
Pii ii base 36 system ii value from 0 to z is subtracted 129
Pii ii decimal ii value is added 129
Pii ii decimal ii value is subtracted 129
When continuously increasing and decreasing numbers like serial numbers are to be printed on labels continuous printing can be performed automatically by the counter in the printer at this time the number of steps for increasing and decreasing addition and subtraction width and number of prints of the same label can be set 129
100 100 100 130
94 103 10f 130
96 103 10a 130
98 100 105 130
Fig fig fig fig 130
Sample printing 131
Chapter 5 132
Interface functions interface functions 132
Rs 232c serial interface 133
C communication control flowchart 135
The following is a reference flowchart for sending and receiving data the following is a reference flowchart for sending and receiving data by using printer transmission request command 01 a or 01 f in xon xoff protocol and compatible machine on mode 135
Parallel interface 137
Appendixes 139
A feedback character transmission validness 140
A setting date and time transmission 140
Appendix 1 list of commands 140
B date and time transmission request 140
Cnnnn setting continuous paper length 140
D setting 2 page edit mode double buffer 140
E selecting edge sensor for paper position detection 140
Ennnn setting number of printing sheets for edited format 140
Error status transmission request 4 byte 140
F label one sheet feed 140
Fnnn setting paper position setting when cutting and peeling 140
G printing edited format 140
Imfaa writing graphic data 140
Imtnn truetype fonts downloading command 140
J setting pause per each label printing 140
Kdabc printer settings 140
N a not supported command n a not supported command 140
Y supported command 140
Clearing memory module contents in file units 141
Information in memory module transmission request 141
Packing memory module contents 141
Select command set 141
Selecting default module a b 141
Sensor level issued to port 141
Setting memory switch contents 141
Setting printing method 141
Test print for printer status 141
Testing flash memory 141
Truetype fonts symbol set selection 141
Version number transmission request 141
Appendix 2 list of font character codes 146
System font 1 6 146
System font 7 ocr a 146
Expansion font cg triumvirate cg triumvirate bold smooth font 147
System font 8 ocr b 147
Appendix 3 printing edit function 148
Area sizes such as each buffer and register vary by model 149
For details refer to appendix 6 list of specifications by model 149
Module allocations vary depending on the command set 149
This module allocation is for dm4 dm8 149
Appendix 4 specification of switching of control codes 152
Control codes can be switched from the menu on the operation panel by setting to alt mode the system level command start code soh immediate execution command and stx sequential execution command will be changed to the commands in the table below when setting alt mode replace the standard codes in the table below of this command reference with the corresponding codes in alt mode 152
Appendix 5 specification list of command set 153
Table below are items whose specifications will be changed using the switching function of the emulation command sets 153
Appendix 6 list of specifications by model 154
Table below are specifications required when editing printing for each model such as memory size and the maximum page length 154

Citizen CL-E720DT [119/154] Outline

Содержание

Похожие устройства