Bosch GKS 65 GCE — основные меры безопасности при работе с пилой [15/220]

OBJ BUCH 359 003 book Page 15 Thursday June 9 2011 10 18 AM English I 15 Kickback is the r esu It of saw misuse and or incorrect oper ating procedures or conditions and can be avoided by tak protected coasting blade will cause thesaw to walk back wards cutti ng whatever is in its path Be aware of the ti me ing proper precautions as given below it takes for the blade to stop after switch is released Maintain a firm grip with both hands on the saw and po sition your arms to resist kickback forces Position your body to either side of theblade but not in line with the blade Kickback could cause the saw to jump back wards but kickback forces can be controlled by the opera tor if proper precautions are taken When blade is binding or when interrupting a cut for a ny rea son release the trigger a nd hold the sa w mo tionless in the material until the blade comes to a com plete stop Nev er a ttempt to remove th e sa w from th e work or pull the saw backward whilethe blade isinmotion or kickback may occur Investigate and take correc tive actions to eliminate the cause of blade binding When restartinga saw inthe workpiece centrethe saw blade in the kerf and check that saw teeth are not en gaged into the material If saw blade is binding it may walk up or kickback from the workpiece as thesawisrestarted Support large panels to minimise the risk of blade Additional safety warnings Do not reach intothesaw dust ejedor withyour hands They could be injured by rotating parts Dond work overhead with the saw In this manner you do not have sufficient control over the power tool Use suitable detedors to ddermine if utility lines are hidden in the work area or call thelocalutilitycompany for assistance Con tact with electriclines can lead to fire and electricshock Damaging agas line can lead to explo sion Penetrating awater line causes property damage or may cause an electricshock Do not operate the power tool stationary It is not de signed for operation with a saw table Do not use high speed steel HSS saw blades Such saw blades can easily break Donot saw ferrous metals Red hot chips can ignite the dust extraction When working with the machine always hold it firmly pinching and kickback Large panels tend to sag under their own weight Supports must be placed under the pan with both hands and provi de for a secure stance The el on both sides near the line of cut and near the edge of Secure the workpiece A workpiece clamped with clamp the panel Do not use dull or damaged blades Unsharpened or im properly setblades producenarrow kerf causing excessive friction blade binding and kickback Bia de dept ha nd bevel adjusting locking levers must be power tool is guided more secure with both hands ing devices or in a vice is held more secure than by hand Always wait until themachinehascometoa complete stop before placing it down The tool insert can jam and lead to loss of control over the power tool tight and secure before making cut If blade adjustment Products sold in GB only Your product is fitted with a BS1363 A approved electric plug with internal fuse ASTA shifts while cutting it may cause binding and kickback approved to BS1362 Use extra caution when sawing into existing walls or other blind areas The protruding blade may cut objects that can cause kickback Lower guard function Check lower guard for proper closing before each use Do not operate the saw if lower guard does not move freely and close instantly Never clamp ortiethelower guard into the open position If saw is accidentally dropped lower guard may be benL Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the bladeor any other part in all angles and depths ofcuL If the plug is notsuitable for your socket outlets it should be cutoff and an appropriate plug fitted in its placeby an author ised customer service agenL The replacement plug should have the same fuse rating as the original plug The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted intoa mains sock et elsewhere Products sold in AUS and NZ only Use a residual current de vice RCD wi th a rated resi dual current of 30 mA or I ess Product Description and Specifica tions Checkthe operation of thelower guard spring If the guard and the spring are not operating properly they Read all safety warnings and all instruc must be serviced before use Lower guard may operate tions Failure tofollow the warnings and in structions may result in electric shock fire sluggishly due to damaged parts gummy deposits or a build up of debris Lower guard maybe retracted manually only for spe cial cuts such as plunge cuts and compound cuts and or serious injury While reading the operating instructions unfold the graphics page for the machi ne and I eave it open Ra ise lower gua rd by retra ding ha ndle and a s soon a s blade entersthematerial the lower guard must be re leased For all other sawing the lower guard should oper ate automatically Always observe that the lower guard iscoveringthe blade before placing saw down on bench or floor An un Bosch Power Tools Intended Use GKS65 GKS65 G The machine is intended for lengthways and crossways cut ting of wood with straight cutting lines as well as mitre cuts in 1619X06 4421 9 6 11