![Hitachi CS40EANG [12/92] English](/img/pdf.png)
Hitachi CS40EANG [12/92] English
![Hitachi CS40EANG [12/92] English](/views2/1081641/page12/bgc.png)
12
English
Guide bar (Fig. 35)
Before using the machine, clean the groove and oiler port (39) in the
bar with the special gauge off ered as an optional accessory.
Side case (Fig. 36)
Always keep the side case and drive area clean of saw dust and
debris. Periodically apply oil or grease to this area to protect from
corrosion as some trees contain high levels of acid.
Fuel fi lter (Fig. 37)
Remove the fuel fi lter from the fuel tank and thoroughly wash it in
solvent. After that, push the fi lter into the tank completely.
NOTE
If the fi lter is hard due to dust and dirt, replace it.
Chain oil fi lter (Fig. 38)
Remove the oil fi lter and thoroughly wash it in solvent.
Cleaning the cylinder fi ns (Fig. 39)
When wood chips are caught between cylinder fi ns (40), the engine
may overheat, resulting in lower output. To avoid this, always keep
cylinder fi ns and fan case clean.
Every 100 operating hours, or once a year (more often if conditions
require), clean fi ns and external surfaces of engine of dust, dirt and
oil deposits which can contribute to improper cooling.
For long-term storage
Drain all fuel from the fuel tank. Start and let engine run until it stops.
Repair any damage which has resulted from use. Clean the unit with
a clean rag, or the use of high pressure air hose. Put a few drops of
two-cycle engine oil into the cylinder through the spark plug hole,
and spin the engine over several times to distribute oil.
Cover the unit and store it in a dry area.
CHAIN SHARPENING
Parts of a cutter (Fig. 40, 41)
WARNING
○ Gloves should be used when sharpening chain.
○ Be sure to round off the front edge to reduce the chance of
kickback or tie-strap breakage.
41. Top plate
42. Working corner
43. Side plate
44. Gullet
45. Heel
46. Chassis
47. Rivet hole
48. Toe
49. Depth gauge
50. Correct angle on top plate (degree of angle depends on chain
type)
51. Slightly protruding “hook” or point (curve on non-chisel chain)
52. Top of depth gauge at correct height below top plate
53. Front of depth gauge rounded off
LOWERING DEPTH GAUGES WITH A FILE
1) If you sharpen your cutters with a fi le holder, check and lower the
depth.
2) Check depth gauges every third sharpening.
3) Place depth gauge tool on cutter. If depth gauge projects, fi le
it level with the top of the tool. Always fi le from the inside of the
chain toward an outside cutter. (Fig. 42)
4) Round off front corner to maintain original shape of depth gauge
after using depth gauge tool. Always follow the recommended
depth gauge setting found in the maintenance or operator
manual for your saw. (Fig. 43)
GENERAL INSTRUCTIONS FOR FILING CUTTERS
File (54) cutter on one side of the chain from the inside out. File on
forward stroke only. (Fig. 44)
5) Keep all cutters the same length. (Fig. 45)
6) File enough to remove any damage to cutting edges (side plate
(55) and top plate (56)) of cutter. (Fig. 46)
SHARPENING ANGLES FOR SHARPENING SAW CHAIN
1. Part Number 95VP
2. Pitch 0.325”
3. Depth Gauge Setting 0.025"
4. Side Plate Filing Angle 85°
5. Top Plate Angle 30°
6. File Guide Angle 10°
Maintenance schedule
Below you will fi nd some general maintenance instructions. For
further information please contact HITACHI dealer.
Daily maintenance
○ Clean the exterior of the unit.
○ Clean the chain oil fi lter port.
○ Clean the groove and oil fi lter port in the guide bar.
○ Clean the side case of saw dust.
○ Check that the saw chain is sharp.
○ Check that the bar nuts are suffi ciently tightened.
○ Make sure that the chain transport guard is undamaged and that
it can be securely fi tted.
○ Check that nuts and screws are suffi ciently tightened.
Especially inspect the bolt of muffl er and ensure that they are
properly tightened before starting engine. Should any of the
bolts be loose, retighten them immediately. Failure to do so
could result in serious hazard.
○ Check the tip of the bar. Please exchange it for the new one
when it is worn out.
○ Check the band of chain brake. Please exchange it for the new
one when it is worn out.
Weekly maintenance
○ Check the starter, especially cord and return spring.
○ Clean the exterior of the spark plug.
○ Remove the spark plug and check the electrode gap. Adjust it to
0.6 mm or change the spark plug.
○ Clean the cooling fi ns on the cylinder and check that the air
intake at the starter is not clogged.
○ Clean the air fi lter.
Monthly maintenance
○ Rinse the fuel tank with gasoline, and clean fuel fi lter.
○ Clean chain oil fi lter.
○ Clean the exterior of the carburetor and the space around it.
○ Clean the fan and the space around it.
NOTE
When ordering the parts to your nearest dealer, please use the
item numbers showing on the parts breakdown section in this
instruction.
BAR NO.
LENGTH-
TYPE
CHAIN NO.
MODEL NO.
OREGON
107498
105191
104968
105355
13”
15”
16”
18”
95VP-56
95VP-64
95VP-66
95VP-72
000Book_CS40EA_EE.indb 12000Book_CS40EA_EE.indb 12 2010/09/03 14:50:322010/09/03 14:50:32
Содержание
- Cs 40ea 1
- English 6
- Meanings of symbols 6
- What is what 6
- English 7
- Warnings and safety instructions 7
- English 8
- Specifications 8
- Assembly procedures 9
- English 9
- Operating procedures 9
- English 10
- English 11
- Maintenance 11
- English 12
- Bedeutungen der symbole 13
- Deutsch 13
- Teilebezeichnungen 13
- Übersetzung der original gebrauchsanweisung 13
- Deutsch 14
- Warn und sicherheitshinweise 14
- Deutsch 15
- Technische daten 15
- Betrieb 16
- Deutsch 16
- Zusammenbau 16
- Deutsch 17
- Deutsch 18
- Deutsch 19
- Wartung 19
- Deutsch 20
- Tι ειναι τι 21
- Ελληνικά 21
- Επεξηγηση συμβoλων 21
- Μετάφραση των αρχικών οδηγιών 21
- Ελληνικά 22
- Προειδοποιησεισ και υποδειξεισ ασφαλειασ 22
- Ελληνικά 23
- Διαδικασιεσ συναρμολογησησ 24
- Ελληνικά 24
- Τεχνικα χαρακτηριστικα 24
- Διαδικασια λειτουργιασ 25
- Ελληνικά 25
- Ελληνικά 26
- Ελληνικά 27
- Συντηρηση 27
- Ελληνικά 28
- Ελληνικά 29
- Polski 30
- Tłumaczenie oryginalnych instrukcji 30
- Zasadnicze podzespoły urządzenia 30
- Znaczenie symboli 30
- Ostrzeżenie i instrukcje bezpieczeństwa 31
- Polski 31
- Polski 32
- Specyfikacje 32
- Polski 33
- Procedury montażu 33
- Procedury obsługi 33
- Polski 34
- Konserwacja 35
- Polski 35
- Polski 36
- Polski 37
- Fordítás az eredeti útmutatót 38
- Magyar 38
- Mi micsoda 38
- Szimbólumok jelentései 38
- Figyelmeztetések és biztonsági óvintézkedések 39
- Magyar 39
- Magyar 40
- Technikai adatok 40
- Magyar 41
- Működtetési eljárások 41
- Összeszerelési eljárások 41
- Magyar 42
- Karbantartás 43
- Magyar 43
- Magyar 44
- Magyar 45
- Co je co 46
- Překlad původních pokynů 46
- Význam symbolů 46
- Čeština 46
- Varování a bezpečnostní pokyny 47
- Čeština 47
- Montážní postupy 48
- Specifikace 48
- Čeština 48
- Obsluha 49
- Čeština 49
- Čeština 50
- Údržba 51
- Čeština 51
- Čeština 52
- Asıl talimatların çevirisi 53
- Sembollerin anlamlari 53
- Tanimlar 53
- Türkçe 53
- Türkçe 54
- Uyarilar ve güvenli k tali matlari 54
- Spesi fi kasyonlar 55
- Türkçe 55
- Montaj i şlemleri 56
- Türkçe 56
- Çaliştirma 56
- Türkçe 57
- Türkçe 58
- Türkçe 59
- Türkçe 60
- Ce şi ce este 61
- Română 61
- Semnificaţia simbolurilor 61
- Traducerea instrucţiunilor originale 61
- Avertismente şi instrucţiuni de siguranţă 62
- Română 62
- Română 63
- Specificatii 63
- Proceduri de asamblare 64
- Proceduri de operare 64
- Română 64
- Română 65
- Română 66
- Mentenanţă 67
- Română 67
- Română 68
- Opis sestavnih delov 69
- Pomen simbolov 69
- Prevod originalnih navodil 69
- Slovenščina 69
- Opozorila in varnostna navodila 70
- Slovenščina 70
- Postopek montaže 71
- Slovenščina 71
- Specifikacije 71
- Postopek upravljanja 72
- Slovenščina 72
- Slovenščina 73
- Slovenščina 74
- Vzdrževanje 74
- Slovenščina 75
- Значение символов или табличек 76
- Перевод оригинальных инструкций 76
- Русский 76
- Что это такое 76
- Предостережения и инструкции по технике безопасности 77
- Русский 77
- Русский 78
- Русский 79
- Сборочные операции 79
- Спецификации 79
- Рабочие операции 80
- Русский 80
- Русский 81
- Русский 82
- Техобслуживание 82
- Русский 83
- Русский 84
- Book_cs40ea_ee indb 91 000book_cs40ea_ee indb 91 2010 09 03 14 50 41 2010 09 03 14 50 41 91
- Clonshaugh business technology park dublin 17 lreland 91
- Deklaracja zgodności z eci 91
- Deutsch 91
- Ec declaration of conformity 91
- Ek megfelelőségi nyilatkozat 91
- English 91
- Erklärung zur konformität mit ce regeln 91
- F tashimo vice president director 91
- Head offi ce in japan 91
- Hitachi koki co ltd 91
- Hitachi koki europe ltd 91
- Hitachi power tools europe gmbh 91
- Magyar 91
- Polski 91
- Prohlášení o shodě s ec 91
- Representative offi ce in europe 91
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 91
- Siemensring 34 47877 willich 1 f r germany 91
- Technical fi le at 91
- Čeština 91
- Εκ δηλωση εναρμ νισμ υ 91
- Ελληνικά 91
- Ab uygunluk beyani 92
- Book_cs40ea_ee indb 92 000book_cs40ea_ee indb 92 2010 09 03 14 50 41 2010 09 03 14 50 41 92
- Clonshaugh business technology park dublin 17 lreland 92
- Code no e99006391 g printed in china 92
- Declaraţie de conformitate ce 92
- Ec deklaracija o skladnosti 92
- F tashimo vice president director 92
- Head offi ce in japan 92
- Hitachi koki co ltd 92
- Hitachi koki europe ltd 92
- Hitachi power tools europe gmbh 92
- Pyсский 92
- Representative offi ce in europe 92
- Română 92
- Sadece avrupa ülkeleri için geçerlidir orman hizmeti için portatif elektrikli testere cs40ea 92
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 92
- Siemensring 34 47877 willich 1 f r germany 92
- Slovenščina 92
- Technical fi le at 92
- Türkçe 92
- Valabil numai pentru europa fierăstrău portabil cu lanţ pentru servicii forestiere cs40ea 92
- Velja le za evropo prenosna verižna žaga za gozdno službo cs40ea 92
- Декларация соответствия ес 92
- Только для европы портативная цепная пила для лесных работ cs40ea 92
Похожие устройства
- Hitachi CS40YNS Инструкция по эксплуатации
- Hitachi CS40ELNA Инструкция по эксплуатации
- Fiskars ерный/оранжевый 115360 Инструкция по эксплуатации
- Husqvarna LC 551SP 9673432-01 Инструкция по эксплуатации
- Калибр НПЦ-250/15НК Инструкция по эксплуатации
- RedVerg RD-GC62-20 6615725 Инструкция по эксплуатации
- RedVerg RD5461C-120A 5019112 Инструкция по эксплуатации
- RedVerg RD4380C-100A 5019111 Инструкция по эксплуатации
- RedVerg RD5461C-130A 5019113 Инструкция по эксплуатации
- Patriot pT 4355 IMPERIAL 250108105 Инструкция по эксплуатации
- Интерскол АМ-110/2000В 239.1.0.00 Инструкция по эксплуатации
- Patriot ES 2216 220301520 Инструкция по эксплуатации
- Patriot PT 47LS 512109014 Инструкция по эксплуатации
- Patriot sE 30 732304621 Инструкция по эксплуатации
- Patriot КАЛУГА 440107560 Инструкция по эксплуатации
- Patriot PТ 4520 220105560 Инструкция по эксплуатации
- Patriot F 300 315302417 Инструкция по монтажу и эксплуатации
- Patriot PS 710 E426108475 Инструкция по эксплуатации
- Patriot PT 2512 220104500 Инструкция по эксплуатации
- Makita BUB143Z Инструкция по эксплуатации