![Fluke 1760 [25/110] Warning](/img/pdf.png)
Fluke 1760 [25/110] Warning
![Fluke 1760 [25/110] Warning](/views2/1005066/page25/bg19.png)
Introduction
Design and Functions 1
1-15
Note
The LED OK is red if no valid sensor can be detected.
The limits for ‘Signal too low’ and ‘Signal too high’ are equal to the
thresholds for voltage dips and voltage swells (e.g.
±
10 % of Un).
For current inputs ‘Signal too low’ is indicated for half cycle or full cycle
rms values below 10 % of the sensor range as configured in the “Hardware
Settings” panel (if sensor is set to “Auto” the “Signal too low” indication
is deactivated).
‘Over range’ is indicated if the input signal is outside the valid range of the
analogue to digital converter (ADC, i.e.
±
32.700 counts).
The phase voltages UL1, UL2, and UL3 of a three-phase system are monitored with the
symmetrical components (zero, positive and negative system). If the negative system
exceeds an upper threshold a wrong phase sequence condition is indicated (e.g. two lines
interchanged); the associated LEDs are flashing in sequence L3-L2-L1.
WX Warning
The LEDs do not indicate whether there is voltage. Do not rely
on the LEDs to find out whether the device under test is live or
not.
D Ethernet port
Used for connection of the Recorder to an Ethernet port of a PC, or to an Ethernet
network (LAN). For a connection to an Ethernet network use the supplied Ethernet cable.
For direct connection of the instrument to a PC use the cross-linked Ethernet cable (with
the red plug).
E 2 USB connectors
Two USB type A connectors for connection of the instrument to the USB-port of a PC.
USB version V2.0 is supported. A special link cable has to be used (USB cable A-A).
USB connectors have 2 functions:
1. Virtual network connection with USB data link cable
2. Memory stick support for storing of measurement data (same as external CF
card)
CF card LED behaviour during USB copy process:
• copy process started --> flashing LED
• copy process finished and all data copied --> LED goes off
• copy process finished but not all data could be copied --> LED is turned on
statically
• on error --> fast flashing LED for approx. 3 seconds then statically on
Note
USB stick must not be pulled out while CF card LED is flashing. This can
cause permanent damage to the storage media. Only remove CF card /
USB stick while CF card LED is OFF or statically ON.
Содержание
- Power quality recorder 1
- Users manual 1
- Limited warranty and limitation of liability 2
- Table of contents 3
- List of tables 7
- List of figures 9
- Chapter 1 11
- Introduction 11
- About this manual 13
- Symbols 13
- Cat identification 14
- Safety instructions 14
- Warnin 14
- Warnings 14
- Mains connection 17
- Safety instructions on device housing 17
- Warning 17
- Design and functions 18
- Input voltage œ measuring inputs 18
- Mains connection and interfaces 18
- Servicing and maintenance 18
- Functional description 20
- C led indicators 21
- Introduction design and function 21
- Leds in the field power 21
- Overview 21
- Leds ch1 to ch8 24
- The following information is provided in case a valid sensor is detected 24
- The following information is provided in case no valid sensor is detected 24
- Three leds are assigned to each of the eight input channels of the recorder the indicators refer to half cycle or full circle rms values of the input signal depending on the configuration 24
- Warning 25
- F serial port com1 rs232 26
- G feature connector 26
- Maximum load current 5 ma 26
- Pin assignment 26
- Serial port for connection of the device to the serial port of a pc 26
- Specification of outputs inputs 26
- The default settings are 57 00 baud 8 data bits 1 stop bit no parity 26
- H measurement channels 27
- Introduction design and function 27
- Note inputs that are not in use must be covered with the supplied protective caps to prevent pollution 27
- Pin assignment 27
- Plugs for 8 isolated measurement channels connect only original accessories such as voltage and current sensors clamps flexi set shunt resistors etc the plug is secured by means of a bayonet mechanism 27
- When analyzing transients with options 2540582 2540575 the potential to earth ground is measured 27
- Basic measurements 28
- Measurement types 28
- Measurements 29
- Chapter 2 31
- Getting started 31
- Checking of delivery 33
- Startup 33
- Installation 34
- Switching the device off 34
- Switching the device on 34
- W x warning 34
- Simple measurement function check 35
- After successful connection you see a green light in the lower right corner next to status information about the instrument 36
- In the live modes section press setup 36
- In the search devices dialog press search select your instrument in the list and press connect 36
- Storage 39
- Transport 39
- Transport and storage 39
- Chapter 3 41
- Operation 41
- Connecting sequence 43
- Connections to measuring circuits 43
- Warning 43
- Connection diagrams 44
- Phase measurement 44
- Wire network with two current sensors aron2 method 45
- Wire network with two current sensors aron2 method open delta method 47
- Wire network 3 wattmeter method 48
- Four wire network three wattmeter method with n conductor voltage and n conductor current 49
- Associated pc software settings 50
- Check the respective option 50
- If required you have the option to determine events flicker and harmonics of the phase to phase voltages 50
- Two star connected voltage systems 51
- Two voltage systems in delta configuration 52
- Methods of measurement formulas 53
- Parameter aggregation 53
- Aggregations 200 ms and higher 54
- Calculation of power parameters 54
- I u p ϕ 54
- Real power 54
- Apparent power 55
- Q q q q 55
- Reactive power 55
- Arctan cos co 56
- Displacement power factor cos 56
- Power factor 56
- Q q q q 56
- S p pf 56
- Half and full cycle aggregations 57
- I i i u p 57
- Real power 57
- Apparent power 58
- Events and flicker 58
- P p p p 58
- Power factor 58
- Q q q q 58
- Reactive power 58
- S p pf 58
- S s s s 58
- Harmonics and interharmonics parameters 59
- K factor and factor k 60
- N v v thd 60
- V n thd 60
- H i p p k 61
- I i n i i e e k 61
- Signaling voltage 62
- Sin 240 sin 120 cos 240 cos 3 1 62
- Unbalance overdeviation underdeviation 62
- Φ ϕ ϕ ϕ 62
- 100 6 3 1 63
- Current unbalance 63
- Overdeviation and underdeviation 64
- Operation methods of measurement formula 65
- Table 3 2 parameter aggregation matrix 65
- Chapter 4 67
- Maintenance 67
- Cleaning 69
- Introduction 69
- Maintenance of battery package 69
- Decommissioning and disposal 70
- Replacement of battery pack 70
- Shutting down 70
- Wx warning 70
- Recalibration 71
- Recycling and disposal 71
- Warranty 71
- Chapter 5 73
- Specifications 73
- General specifications 75
- Specifications general specification 75
- Specifications general specification 77
- Instrument with 600v 1000v sensor 78
- Chapter 6 79
- Options and accessories 79
- Accessories 81
- All probes contain a memory for calibration factors sensor identity and serial number which is read automatically by the instrument ranges can be selected in the pq analyze software 81
- Instruments 81
- Options and accessories instrument 81
- Other measuring transducers can be connected to the inputs of these sensors 81
- The current sensor for direct current measurement shunt is available for 20 ma 81
- The flexible current sensors tps flex are available for ranges between 100 a and 6000 a ac 2 ranges can be selected in the pq analyze software 81
- The passive current clamps ac only are available in ranges with 1 a up to 1000 a 2 ranges can be selected in the pq analyze software 81
- The voltage probes for various ranges between 10 v and 1000 v are available for the instrument 81
- Aging 0 5 year 82
- All voltage sensors are suitable for dc for dc and ac up to 5 khz 82
- Standard voltage probes for ac and dc 82
- Temperature coefficient 100 ppm k 82
- Current probes for ac currents 83
- Flexible current probes for ac 83
- Options and accessories accessorie 83
- Current clamp 1 a 10 a ac 84
- Other accessories 84
- Shunt resistors for ac and dc currents 84
- W warning 85
- Phase angle in degrees primary current in a 86
- Dimensions in mm 87
- Current clamp 5 a 50 a ac 89
- W warning 90
- Phase angle in degrees primary current in a 91
- Current clamp 20 a 200 a ac 92
- W warning 93
- Accuracy typical for 50 60 hz 94
- Linearity error in of measured value primary current in a 94
- Flexi current sensor 100 a 500 a 96
- W warning 97
- Phase angle in degrees primary current in a 98
- Flexi current sensor 200 a 1000 a 100
- W warning 101
- Phase angle in degrees primary current in a 102
- Flexi current sensor 3000 a 6000 a 103
- W warning 104
- Gps time synchronization œ 2539223 106
- Options 106
Похожие устройства
- LG MS-2355F Инструкция по эксплуатации
- DBX 1046 Инструкция по эксплуатации
- Supra SCD-309U Инструкция по эксплуатации
- Ada 3D Liner 2V А00131 Инструкция по эксплуатации
- Belkin F8N180ea Black Инструкция по эксплуатации
- LG F1280NDS5 Инструкция по эксплуатации
- Fluke 190 Инструкция по эксплуатации
- LG MS-2354Y Инструкция по эксплуатации
- DBX 160A Инструкция по эксплуатации
- Supra SCD-307U Инструкция по эксплуатации
- Belkin Home Theater Power PF30 Black Инструкция по эксплуатации
- Ada 3D Liner 4V А00133 Инструкция по эксплуатации
- LG F1280NDS Инструкция по эксплуатации
- Fluke 2042 Инструкция по эксплуатации
- LG MS-2354G Инструкция по эксплуатации
- DBX 1066 Инструкция по эксплуатации
- Belkin Home Theater Power PF50 Black Инструкция по эксплуатации
- LG F-1029SDR Инструкция по эксплуатации
- LG MS-2352U Инструкция по эксплуатации
- Fluke 233 Инструкция по эксплуатации