Skil 0750 RA [10/152] Application advice

Skil 0750 RA [10/152] Application advice
10
APPLICATIONADVICE
For trimming a hedge at a uniform height level
- fasten a piece of string along the length of the hedge
at the desired height
- trim the hedge just above this string
Recommended cutting/trimming times (Western Europe)
- trim hedges with deciduous leaves in June and
October
- trim evergreen hedges in April and August
- trim conifers and other fast-growing shrubs every 6
weeks from May until October
MAINTeNANCe / serVICe
This tool is not intended for professional use
Keep tool, charger and cutting blades clean
! unplugchargerfrompowersourcebefore
cleaning
! alwaysremovethebatterybeforecleaning
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- clean ventilation slots J 2 regularly with a brush or
compressed air
- after use, always carefully clean and lightly lubricate
the cutting blades
! weargloveswhenhandlingorcleaningthe
cuttingblades
Regularly check the condition of the cutting blades and
the tightness of the blade bolts
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
Sharpening the cutting blades
! removebatteryfromtool
- remove cutting blades from tool before sharpening
- sharpen the cutting blades with a small and smooth
le, in case a solid object damaged them
- we advise you, however, to have the blades sharpened
by a specialist
- lubricate the cutting blades after sharpening
Storage ¡
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail K on the wall with 4 screws
(notsupplied) and horizontally leveled
- use blade guards L 2 when storing the tool
- lubricate the cutting blades before storing the tool
If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
- in case of a defective charger send bothchargerand
battery to your dealer or the SKIL service station
TroUBlesHooTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switchoffthetoolandremovethebatterybefore
investigatingtheproblem
Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/o switch defective -> contact dealer/service
station
Motor runs but blades remain stationary
- internal fault -> contact dealer/service station
Cutting blades hot
- cutting blades blunt -> have blades sharpened
- cutting blades have dents -> have blades inspected
- too much friction due to lack of lubricant -> lubricate
blades
eNVIroNMeNT
Donotdisposeofelectrictools,batteries,
accessoriesandpackagingtogetherwithhousehold
wastematerial (only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @ will remind you of this when the need for
disposing occurs
The nickel-metalhydride battery must be kept separate
from the natural environment and should not be disposed
of as normal domestic waste (symbol # will remind you
of this when the need for disposing occurs)
! priortodisposalprotectbatteryterminalswith
heavytapetopreventshort-circuit
- dispose of the batteries at an ocial collection point
for batteries
! batteriesmayexplodewhendisposedofinfire,
sodonotburnbatteryforanyreason
deClArATIoN oF CoNForMITY
We declare under our sole responsibility that the product
described under “Technical data” is in conformity with the
following standards or standardization documents: EN
60335, EN 60745, EN 61000, EN 55014 in accordance
with the provisions of the directives 2006/95/EC,
2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU
Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
¹ÊÁÂÆιÆ¼½ÊÇǾ¼½Æ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
Ĺ¾ÁÂÿʹ¹¾
ÈÈÊÇιÄ¹Æ¹¿½Ê
24.02.2014
10
NoIse/VIBrATIoN
Measured in accordance with EN 60745 the sound
pressure level of this tool is 58 dB(A) and the sound
power level 78 dB(A) (standard deviation: 3 dB), and the

Содержание

APPLICATION ADVICE switch off the tool and remove the battery before Investigating the problem Tool operates intermittently internal wiring defective contact dealer service station on off switch defective contact dealer service station Motor runs but blades remain stationary internal fault contact dealer service station Cutting blades hot cutting blades blunt have blades sharpened cutting blades have dents have blades inspected too much friction due to lack of lubricant lubricate blades For trimming a hedge at a uniform height level fasten a piece of string along the length of the hedge at the desired height trimthehedgejustabovethisstring Recommended cutting trimming times Western Europe trim hedges with deciduous leaves in June and October trim evergreen hedges in April and August trim conifers and other fast growing shrubs every 6 weeks from May until October MAINTENANCE SERVICE This tool is not intended for professional use Keep tool charger and cutting blades clean I unplug charger from power source before cleaning I always remove the battery before cleaning clean the tool with a damp cloth do not use cleaning agents or solvents clean ventilation slots J regularly with a brush or compressed air after use always carefully clean and lightly lubricate the cutting blades wear gloves when handling or cleaning the cutting blades Regularly check the condition of the cutting blades and the tightness of the blade bolts Regularly check for worn or damaged components and have them repaired replaced when necessary Sharpening the cutting blades I remove battery from tool rem we cutting blades from tool before sharpening sharpen the cutting blades with a small and smooth file in case a solid object damaged them we advise you however to have the blades sharpened by a specialist lubricate the cutting blades after sharpening Storage store the tool Indoors in a dry and locked up place out of reach of children securely mount storage rail K on the wall with 4 screws not supplied and horizontally leveled use blade guards L when storing the tool lubricate the cutting blades before storing the tool If the tool charger should fail despite the care taken in manufacturing and testing procedures repair should be carried out by an after sales service centre for SKIL power tools send the tool or charger undismantled together with proof of purchase to your dealer or the nearest SKIL service station addresses as well as the service diagram of the tool are listed on www skil com in case of a defective charger send both charger and battery to your dealer or the SKIL service station TROUBLESHOOTING The following listing shows problem symptoms possible causes and corrective actions if these do not identify and correct the problem contact your dealer or service station ENVIRONMENT Do not dispose of electric tools batteries accessories and packaging together with household waste material only for EU countries in observance of European Directive 2012 19 EC on waste of electric and electronic equipment and its implementation in accordance with national law electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility symbol will remind you of this when the need for disposing occurs The nickel metalhydride battery must be kept separate from the natural environment and shoul d n ot be di sposed of as normal domestic waste symbol will remind you of thiswhen the need for disposing occurs prior to disposal protect battery terminals with heavy tape to prevent short circuit dispose of the batteries at an official collection point for batteries I batteries may explode when disposed of In fire so do not burn battery for any reason DECLARATION OF CONFORMITY C We declare under our sole responsibility that the product described under Technical data is in conformity with the following standards or standardization documents EN 60335 EN 60745 EN 61000 EN 55014 in accordance with the precisions of the directives 2006 95 EC 2004 108 EC 2006 42 EC 2000 14 EC 2011 65 EU Technical file at SKIL Europe BV PT SEU ENG1 4825 BD Breda NL Marijn van der Hoofden Operations Engineering Olaf Dijkgraaf Approval Manager SKIL Europe BV 4825 BD Breda NL 24 02 2014 C 1O NOISE VIBRATION Measured in accordance with EN 60745 the sound pressure level of this tool is 58 dB A and the sound power level 78 dB A standard deviation 3dB and the 10

Скачать