Honda CLYMER VF500C 500F (1984-1985) Инструкция по эксплуатации онлайн [129/350] 114521
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Honda CLYMER VF500C 500F (1984-1985) Инструкция по эксплуатации онлайн [129/350] 114521

Honda CLYMER VF500C 500F (1984-1985) Инструкция по эксплуатации онлайн [129/350] 114521
CLUTCH
AND
TRANSMISSION
tzl
1. Screw
2. Cover
3. Diaphragm
4.
Body
5. Rubber
boot
6. Union
bolt
7.
Sealing washer
8. Screw
9. Lockwasher
10.
Switch
11. Clamp
12. Bolt
13. Spring
14. Primary
cup
15. Piston
and
secondary
cup
ib
d
13u
16. Washer
17. Girclip
18.
Boot
19. Pushrod
20. Pushrod end
piece
21.
Hand lever
pivot
bolt
22. Hand
lever
CLUTCH
MASTER
CYLINDER
23. Nut
24.
Upper flexible
hose
25. Hydraulic
hose
26. Lower
flexible hose
27.
Slave
cylinder
28.
Bolt
l2
1
8
fl
the clutch master
cylinder. Remove
the
clutch
hose;
tie the hose
up
and cover
the end
to
prevent
entry
of foreign matter.
4.
Remove
the clamping
bolts
(B,
Figure
32)
and
clamp securing
the
clutch master
cylinder
to the
handlebar
and
remove
the
clutch master
cylinder.
5.
Install
by
reversing
these
removal
steps, noting
the
following.
6.
Position
the clamp with
the UP mark
(A,
Figure
34)
facing
up and install
the
clamp.
7. Align
the clamp mating
surface with
the
punch
mark
on the handlebar
(B,
Figure
34).
8.
Tighten
the
upper
bolt f,rst,
then
the
lower.
Tighten
the
bolts securely.
9.
Install
the
clutch hose
onto
the clutch master
cylinder. Be
sure
to
place
a sealing washer
on
each
side of
the
fitting.
Install
the
union
bolt and tighten
the
union bolt
to the
torque
specifications
listed in
Table 1.
10. Attach
the electrical wires
to the
clutch
switch.
I l. Bleed
the clutch
as described in
this chapter.
Disassembly
Refer
to
Figure
35 for this
procedure.
l.
Remove
the
clutch
master
cvlinder as described
in
this
chapter.
2. Remove
the bolt and nut
securing
the
clutch
lever
and remove
the
lever.
3.
Remove
the screws securing
the cover
and
remove
the cover
and diaphragm;
pour
out the
hydraulic
fluid
and discard it.
Never
reuse
hydraulic
fluid.
4.
Remove
the
pushrod
and the
end
piece.
5. Remove
the
rubber
boot
from
the area where
the hand lever
pushrod
actuates
the internal
piston.
6. Using
circlip
pliers,
remove
the internal
circlip
from
the
body.
7. Remove
the secondary cup and
the
piston
assembly.
8.
Remove
the
primary
cup and spring.
9. Remove
the clutch switch
if necessarv.
Inspection
1.
Clean
all
parts
in
denatured
alcohol or
fresh
hydraulic
fluid.
Inspect the
cylinder bore
and
piston
contact surfaces for
signs of
wear
and
damage. If
either
part
is less than
perfect,
replace
it.
2.
Check
the end of
the
piston
for wear
caused
by
the
hand
lever
pushrod.
Replace
the
piston
if
necessary.

Содержание

Похожие устройства

Скачать