![Qtech QSW-8200-28T-POEAC- DC [73/85] Lldp transmit med tlv extendpoe](/img/pdf.png)
Qtech QSW-8200-28T-POEAC- DC [73/85] Lldp transmit med tlv extendpoe
![Qtech QSW-8200-28T-POEAC- DC [73/85] Lldp transmit med tlv extendpoe](/views2/1596641/page73/bg49.png)
User Manual
Chapter 10. Commands for LLDP-MED 73
www.qtech.ru
Usage Guide: After configuring this command, if the port is able to send LLDP-MED TLV,
the sent LLDP packets with LLDP-MED Capability TLV. However, LLDP packets sent by
the port without LLDP-MED Capability TLV after the switch configured the
corresponding no command. Note: LLDP-MED Capability TLV is the important LLDP-
MED TLV, if do not configure the port to send LLDP-MED Capability TLV firstly, other
LLDP-MED TLV will not be sent.
Example: Port 19 enables the function for sending LLDP-MED Capability TLV.
Switch(Config-If-Ethernet1/0/19)# lldp transmit med tlv capability
10.8 lldp transmit med tlv extendPoe
Command: lldp transmit med tlv extendPoe
no lldp transmit med tlv extendPoe
Function: Configure the specified port to send LLDP-MED Extended Power-Via-MDI TLV.
The no command disables the capability.
Parameter: None.
Default: The function is disabled for sending LLDP-MED Extended Power-Via-MDI TLV.
Command Mode: Port mode
Usage Guide: After configuring this command, if the port is able to send LLDP-MED TLV,
LLDP packets with LLDP-MED Extended Power-Via-MDI TLV sent by the port. However,
LLDP packets without LLDP-MED Extended Power-Via-MDI TLV sent by the port after
the switch configured the corresponding no command. Note: LLDP-MED Capability TLV
sent by the port must be configured before sending LLDP-MED Extended Power-Via-
MDI TLV, or else the configuration cannot be successful. If the device does not support
PoE or PoE function of the port is disabled, although configuring this command, LLDP-
MED Extended Power-Via-MDI TLV will not be sent.
Example: Port 19 enables the function for sending LLDP-MED Extended Power-Via-MDI
TLV.
Switch(Config-If-Ethernet1/0/19)# lldp transmit med tlv extendPoe
10.9 lldp transmit med tlv inventory
Command: lldp transmit med tlv inventory
o no lldp transmit med tlv inventory
Function: Configure the specified port to send LLDP-MED Inventory Management TLVs
aggregation, TLVs aggregation includes 7 TLVs, they are Hardware Revision TLV,
Firmware Revision TLV, Software Revision TLV, Serial Number TLV, Manufacturer Name
TLV, Model Name TLV, Asset ID TLV. The no command disables the capability.
Parameter: None.
Default: The function is disabled for sending LLDP-MED Inventory Management TLVs.
Command Mode: Port mode
Содержание
- Chapter 1 commands for network port configuration 7 2
- Chapter 2 commands for port isolation function 20 2
- Chapter 3 commands for port loopback detection function 23 2
- Commands for ethernet port configuration 7 2
- Content 2
- Debug loopback detection 23 2
- Isolate port apply 21 2
- Isolate port group 20 2
- Isolate port group switchport interface 20 2
- Loopback detection control 23 2
- Loopback detection control recovery timeout 24 2
- Loopback detection interval time 24 2
- Loopback detection specified vlan 25 2
- Show isolate port group 21 2
- Show loopback detection 25 2
- Chapter 1 commands for network port 7
- Commands for ethernet port configuration 7
- Configuration 7
- Chapter 2 commands for port isolation function 20
- Isolate port group 20
- Isolate port group switchport interface 20
- Isolate port apply 21
- Show isolate port group 21
- Chapter 3 commands for port loopback detection 23
- Debug loopback detection 23
- Function 23
- Loopback detection control 23
- Loopback detection control recovery timeout 24
- Loopback detection interval time 24
- Loopback detection specified vlan 25
- Show loopback detection 25
- Chapter 4 commands for uldp 26
- Debug uldp 26
- Debug uldp error 26
- Debug uldp event 26
- Debug uldp fsm interface ethernet 27
- Debug uldp interface ethernet 27
- Debug uldp packet 27
- Uldp aggressive mode 28
- Uldp enable 28
- Uldp disable 29
- Uldp hello interval 29
- Uldp manual shutdown 29
- Show uldp 30
- Uldp recovery time 30
- Uldp reset 30
- Chapter 5 commands for lldp function 32
- Clear lldp remote table 32
- Debug lldp 32
- Debug lldp packets 32
- Lldp enable 33
- Lldp enable port 33
- Lldp mode 33
- Lldp msgtxhold 34
- Lldp neighbors max num 34
- Lldp notification interval 34
- Lldp toomanyneighbors 35
- Lldp transmit delay 35
- Lldp transmit optional tlv 35
- Lldp trap 36
- Lldp tx interval 36
- Show debugging lldp 37
- Show lldp 37
- Show lldp interface ethernet 38
- Show lldp neighbors interface ethernet 38
- Show lldp traffic 39
- Chapter 6 commands for port channel 40
- Debug port channel 40
- Interface port channel 40
- Lacp port priority 41
- Lacp system priority 41
- Lacp timeout 41
- Load balance 42
- Port group 42
- Port group mode 42
- Show port group 43
- Chapter 7 commands for mtu 45
- Chapter 8 commands for efm oam 46
- Clear ethernet oam 46
- Debug ethernet oam error 46
- Debug ethernet oam fsm 46
- Debug ethernet oam packet 47
- Debug ethernet oam timer 47
- Ethernet oam 47
- Ethernet oam errored frame threshold high 48
- Ethernet oam errored frame threshold low 48
- Ethernet oam errored frame period threshold high 49
- Ethernet oam errored frame period threshold low 49
- Ethernet oam errored frame window 49
- Ethernet oam errored frame period window 50
- Ethernet oam errored frame seconds threshold high 50
- Ethernet oam errored frame seconds threshold low 51
- Ethernet oam errored frame seconds window 51
- Ethernet oam errored symbol period threshold high 52
- Ethernet oam errored symbol period threshold low 52
- Ethernet oam errored symbol period window 53
- Ethernet oam link monitor 53
- Ethernet oam mode 54
- Ethernet oam period 54
- Ethernet oam remote failure 54
- Ethernet oam remote loopback 55
- Ethernet oam remote loopback supported 55
- Ethernet oam timeout 56
- Show ethernet oam 56
- Show ethernet oam events 61
- Show ethernet oam link events configuration 64
- Show ethernet oam loopback status 65
- Bpdu tunnel dmac 67
- Bpdu tunnel gvrp 67
- Bpdu tunnel stp 67
- Chapter 9 commands for bpdu tunnel 67
- Bpdu tunnel dot1x 68
- Bpdu tunnel lacp 68
- Bpdu tunnel uldp 68
- Chapter 10 commands for lldp med 70
- Civic location 70
- Description language province state city county street locationnum location floor room postal otherinfo 70
- Ecs location 71
- Lldp med fast count 71
- Lldp med trap 72
- Lldp transmit med tlv all 72
- Lldp transmit med tlv capability 72
- Lldp transmit med tlv extendpoe 73
- Lldp transmit med tlv inventory 73
- Lldp transmit med tlv networkpolicy 74
- Network policy 74
- Show lldp 75
- Show lldp neighbors 77
- Chapter 11 commands for port security 78
- Clear port security 78
- Show port security 78
- Switchport port security 78
- Switchport port security aging 79
- Switchport port security mac address 79
- Switchport port security mac address sticky 80
- Switchport port security maximum 80
- Switchport port security violation 81
- Chapter 12 commands for ddm 82
- Clear transceiver threshold violation 82
- Debug transceiver 82
- Show transceiver 82
- Show transceiver threshold violation 83
- Transceiver monitoring 83
- Transceiver monitoring interval 84
- Transceiver threshold 84
Похожие устройства
- Qtech QSW-8200-28T-POEAC- DC Команды для потокового монитора
- Qtech QSW-8200-28T-POEAC- DC Команды для протокола маршрутизаций
- Qtech QSW-8200-28T-POEAC- DC Команды для протокола многоадресной рассылки
- Qtech QSW-8200-28T-POEAC- DC Команды для функции безопасности
- Qtech QSW-8200-28T-POEAC- DC Команды интерфейса уровня 3
- Qtech QSW-8200-28T-POEAC- DC Команды надёжности
- Qtech QSW-8200-28T-POEAC- DC Команды настройки vlan
- Qtech QSW-8200-28T-POEAC- DC Команды отладки и диагностики
- Qtech QSW-8200-28T-POEAC- DC Команды управления сетевым временем
- Qtech QSW-8200-28T-POEAC- DC Руководство пользователя
- Qtech QSW-8200-28F-AC-DC Команды для dhcp-сервера
- Qtech QSW-8200-28F-AC-DC Команды для mstp
- Qtech QSW-8200-28F-AC-DC Команды для poe
- Qtech QSW-8200-28F-AC-DC Команды для qos
- Qtech QSW-8200-28F-AC-DC Команды для базовой конфигурации
- Qtech QSW-8200-28F-AC-DC Команды для настройки портов
- Qtech QSW-8200-28F-AC-DC Команды для потокового монитора
- Qtech QSW-8200-28F-AC-DC Команды для протокола маршрутизаций
- Qtech QSW-8200-28F-AC-DC Команды для протокола многоадресной рассылки
- Qtech QSW-8200-28F-AC-DC Команды для функции безопасности