![Qtech QSW-8200-28T-POEAC- DC [61/85] Show ethernet oam events](/img/pdf.png)
Qtech QSW-8200-28T-POEAC- DC [61/85] Show ethernet oam events
![Qtech QSW-8200-28T-POEAC- DC [61/85] Show ethernet oam events](/views2/1596641/page61/bg3d.png)
User Manual
Chapter 8. Commands for EFM OAM 61
www.qtech.ru
local_mux_action
Working mode of the local transmitter:
FWD, the port can send any packets;
DISCARD, the port only sends OAMPDU packets and
discards others.
local_par_action
Working mode of the local receiver in the following:
FWD, receiving any packets is allowed;
DISCARD, only OAMPDU packets is received while others
are discarded;
LB, OAM remote loopback is enabled on the port. In this
case, all the packets except OAMPDU packets received
are returned to their sources along the ways they come.
Loopback Supported
Whether support remote loopback: YES for support and
NO for not.
Unidirectional Support
Whether support unidirectional transmission: YES for
support and NO for not.
Link Events
Whether support general link events: YES for support and
NO for not.
Remote Failure
Whether support severe link events: YES for support and
NO for not.
Max_OAMPDU_Size
The maximum length of OAMPDU is supported.
Link Fault
Whether occur a Link Fault event: 0 for no and 1 for yes.
Dying Gasp
Whether occur a Dying Gasp event: 0 for no and 1 for yes.
Critical Event
Whether occur a Critical Event: 0 for no and 1 for yes.
8.27 show ethernet-oam events
Command: show ethernet-oam events {local | remote} [interface {ethernet |}
<IFNAME>]
Function: Shows the statistic information of link events on specified or all ports with
OAM enabled, including general link events and severe link events.
Содержание
- Chapter 1 commands for network port configuration 7 2
- Chapter 2 commands for port isolation function 20 2
- Chapter 3 commands for port loopback detection function 23 2
- Commands for ethernet port configuration 7 2
- Content 2
- Debug loopback detection 23 2
- Isolate port apply 21 2
- Isolate port group 20 2
- Isolate port group switchport interface 20 2
- Loopback detection control 23 2
- Loopback detection control recovery timeout 24 2
- Loopback detection interval time 24 2
- Loopback detection specified vlan 25 2
- Show isolate port group 21 2
- Show loopback detection 25 2
- Chapter 1 commands for network port 7
- Commands for ethernet port configuration 7
- Configuration 7
- Chapter 2 commands for port isolation function 20
- Isolate port group 20
- Isolate port group switchport interface 20
- Isolate port apply 21
- Show isolate port group 21
- Chapter 3 commands for port loopback detection 23
- Debug loopback detection 23
- Function 23
- Loopback detection control 23
- Loopback detection control recovery timeout 24
- Loopback detection interval time 24
- Loopback detection specified vlan 25
- Show loopback detection 25
- Chapter 4 commands for uldp 26
- Debug uldp 26
- Debug uldp error 26
- Debug uldp event 26
- Debug uldp fsm interface ethernet 27
- Debug uldp interface ethernet 27
- Debug uldp packet 27
- Uldp aggressive mode 28
- Uldp enable 28
- Uldp disable 29
- Uldp hello interval 29
- Uldp manual shutdown 29
- Show uldp 30
- Uldp recovery time 30
- Uldp reset 30
- Chapter 5 commands for lldp function 32
- Clear lldp remote table 32
- Debug lldp 32
- Debug lldp packets 32
- Lldp enable 33
- Lldp enable port 33
- Lldp mode 33
- Lldp msgtxhold 34
- Lldp neighbors max num 34
- Lldp notification interval 34
- Lldp toomanyneighbors 35
- Lldp transmit delay 35
- Lldp transmit optional tlv 35
- Lldp trap 36
- Lldp tx interval 36
- Show debugging lldp 37
- Show lldp 37
- Show lldp interface ethernet 38
- Show lldp neighbors interface ethernet 38
- Show lldp traffic 39
- Chapter 6 commands for port channel 40
- Debug port channel 40
- Interface port channel 40
- Lacp port priority 41
- Lacp system priority 41
- Lacp timeout 41
- Load balance 42
- Port group 42
- Port group mode 42
- Show port group 43
- Chapter 7 commands for mtu 45
- Chapter 8 commands for efm oam 46
- Clear ethernet oam 46
- Debug ethernet oam error 46
- Debug ethernet oam fsm 46
- Debug ethernet oam packet 47
- Debug ethernet oam timer 47
- Ethernet oam 47
- Ethernet oam errored frame threshold high 48
- Ethernet oam errored frame threshold low 48
- Ethernet oam errored frame period threshold high 49
- Ethernet oam errored frame period threshold low 49
- Ethernet oam errored frame window 49
- Ethernet oam errored frame period window 50
- Ethernet oam errored frame seconds threshold high 50
- Ethernet oam errored frame seconds threshold low 51
- Ethernet oam errored frame seconds window 51
- Ethernet oam errored symbol period threshold high 52
- Ethernet oam errored symbol period threshold low 52
- Ethernet oam errored symbol period window 53
- Ethernet oam link monitor 53
- Ethernet oam mode 54
- Ethernet oam period 54
- Ethernet oam remote failure 54
- Ethernet oam remote loopback 55
- Ethernet oam remote loopback supported 55
- Ethernet oam timeout 56
- Show ethernet oam 56
- Show ethernet oam events 61
- Show ethernet oam link events configuration 64
- Show ethernet oam loopback status 65
- Bpdu tunnel dmac 67
- Bpdu tunnel gvrp 67
- Bpdu tunnel stp 67
- Chapter 9 commands for bpdu tunnel 67
- Bpdu tunnel dot1x 68
- Bpdu tunnel lacp 68
- Bpdu tunnel uldp 68
- Chapter 10 commands for lldp med 70
- Civic location 70
- Description language province state city county street locationnum location floor room postal otherinfo 70
- Ecs location 71
- Lldp med fast count 71
- Lldp med trap 72
- Lldp transmit med tlv all 72
- Lldp transmit med tlv capability 72
- Lldp transmit med tlv extendpoe 73
- Lldp transmit med tlv inventory 73
- Lldp transmit med tlv networkpolicy 74
- Network policy 74
- Show lldp 75
- Show lldp neighbors 77
- Chapter 11 commands for port security 78
- Clear port security 78
- Show port security 78
- Switchport port security 78
- Switchport port security aging 79
- Switchport port security mac address 79
- Switchport port security mac address sticky 80
- Switchport port security maximum 80
- Switchport port security violation 81
- Chapter 12 commands for ddm 82
- Clear transceiver threshold violation 82
- Debug transceiver 82
- Show transceiver 82
- Show transceiver threshold violation 83
- Transceiver monitoring 83
- Transceiver monitoring interval 84
- Transceiver threshold 84
Похожие устройства
- Qtech QSW-8200-28T-POEAC- DC Команды для потокового монитора
- Qtech QSW-8200-28T-POEAC- DC Команды для протокола маршрутизаций
- Qtech QSW-8200-28T-POEAC- DC Команды для протокола многоадресной рассылки
- Qtech QSW-8200-28T-POEAC- DC Команды для функции безопасности
- Qtech QSW-8200-28T-POEAC- DC Команды интерфейса уровня 3
- Qtech QSW-8200-28T-POEAC- DC Команды надёжности
- Qtech QSW-8200-28T-POEAC- DC Команды настройки vlan
- Qtech QSW-8200-28T-POEAC- DC Команды отладки и диагностики
- Qtech QSW-8200-28T-POEAC- DC Команды управления сетевым временем
- Qtech QSW-8200-28T-POEAC- DC Руководство пользователя
- Qtech QSW-8200-28F-AC-DC Команды для dhcp-сервера
- Qtech QSW-8200-28F-AC-DC Команды для mstp
- Qtech QSW-8200-28F-AC-DC Команды для poe
- Qtech QSW-8200-28F-AC-DC Команды для qos
- Qtech QSW-8200-28F-AC-DC Команды для базовой конфигурации
- Qtech QSW-8200-28F-AC-DC Команды для настройки портов
- Qtech QSW-8200-28F-AC-DC Команды для потокового монитора
- Qtech QSW-8200-28F-AC-DC Команды для протокола маршрутизаций
- Qtech QSW-8200-28F-AC-DC Команды для протокола многоадресной рассылки
- Qtech QSW-8200-28F-AC-DC Команды для функции безопасности