Hitachi DS12DVF3-TB [9/58] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi DS12DVF3-TB [9/58] English

Hitachi DS12DVF3-TB [9/58] English
English
10
䡬 Removing the bit
Securely hold the main unit and pull out the bit
by holding the tip with your thumb (Fig. 15).
CAUTION
䡬 Only Hitachi STANDARD ACCESSORIES phillips bit
(No. 2 × 65L; Code No. 983006) may be used. Do
not use other bits since they may come loose.
11. Using the bit holder
CAUTION
䡬 Stow the bit in the specified location on the tool.
If the tool is used with the bit stowed improperly,
the bit may fall and cause bodily injury.
䡬 Do not stow bits that are of a different length,
gauge or dimension than the plus driver bit (65 mm
long) included in the STANDARD ACCESSORIES.
The bit may fall and cause bodily injury.
(1) Removing the bit
Securely hold the main unit and pull out the bit
by holding the tip with your thumb (Fig. 16).
(2) Installing the Bit
Install the bit with steps opposite of when removing.
Insert the bit so that the right and left sides are
equal, as shown in Fig. 17.
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of as dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or
replace the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Cleaning on the outside
When the driver drill is stained, wipe with a soft
dry cloth or a cloth moistened with soapy water.
Do not use chloric solvents, gasoline or paint thinner,
for they melt plastics.
4. Storage
Store the driver drill in a place in which the tempera
ture is less than 40°C and out of reach of children.
5. Service parts list
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without
prior notice.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to
EN50144.
The typical A-weighted sound pressure level:
64 dB (A) (DS12DVF3).
Wear ear protection.
The typical weighted root mean square acceleration
value: 0.6 m/s
2
(DS12DVF3).

Содержание

Похожие устройства

English O Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb Fig 15 CAUTION O Only Hitachi STANDARD ACCESSORIES phillips bit No 2 x 65L Code No 983006 may be used Do not use other bits since they may come loose 11 Using the bit holder CAUTION O Stow the bit in the specified location on the tool If the tool is used with the bit stowed improperly the bit may fall and cause bodily injury O Do not stow bits that are of a different length gauge or dimension than the plus driver bit 65 mm long included in the STANDARD ACCESSORIES The bit may fall and cause bodily injury 1 Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb Fig 16 2 Installing the Bit Install the bit with steps opposite of when removing Insert the bit so that the right and left sides are equal as shown in Fig 17 Information concerning The measured values EN50144 airborne noise and vibration were determined according to The typical A weighted sound pressure level 64 dB A DS12DVF3 Wear ear protection The typical weighted root mean square acceleration value 0 6 m s2 DS12DVF3 MAINTENANCE AND INSPECTION 1 Inspecting the tool Since use of as dull tool will degrade efficiency and cause possible motor malfunction sharpen or replace the tool as soon as abrasion is noted 2 Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screws be loose retighten them immediately Failure to do so could result in serious hazard 3 Cleaning on the outside When the driver drill is stained wipe with a soft dry cloth or a cloth moistened with soapy water Do not use chloric solvents gasoline or paint thinner for they melt plastics 4 Storage Store the driver drill in a place in which the tempera ture is less than 40 C and out of reach of children 5 Service parts list CAUTION Repair modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance In the operation and maintenance of power tools the safety regulations and standards prescribed in each country must be observed MODIFICATIONS Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements Accordingly some parts may be changed without prior notice NOTE Due to HITACHI S continuing program of research and development the specifications herein are subject to change without prior notice 10

Скачать