Home
Главная
Hitachi
Шуруповерты И Винтоверты
WM14DBL
Инструкция по эксплуатации Страница: 14

Hitachi WM14DBL [14/112] English

English

On the other hand, the electronic clutch mode (reverse

rotation) meets the preset rotation speed immediately

after the start.

䡬 The tool may not return to the initial status from the

striking operation.

When the bit or socket is removed from the screw or

bolt while the switch is being pulled, the tool may

continue the striking operation.

To return to the initial status, turn off the switch and

then start the next operation.

䡬 Motor rotation speed does not decrease even when

the remaining battery power becomes low.

Since this tool adopts the constant-speed control, the

rotation speed is almost unchanged even when the

remaining amount of the battery becomes low. This

allows users to operate the tool efficiently until the

battery runs down. However, it is difficult to know the

remaining battery power from the rotation speed

and the tool may stop suddenly during work.

Check the remaining battery power by pressing the

remaining battery indicator switch at times.

3. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise. (See Fig. 6) (The

and

marks

are provided on the body.)

CAUTION:

The push button can not be switched while the tool is

turning. To switch the push button, stop the tool,

then set the push button.

4. Switch operation

䡬 When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

䡬 The rotational speed can be controlled by varying the

amount that the trigger switch is pulled. Speed is low

when the trigger switch is pulled slightly and increases

as the trigger switch is pulled more.

5. Using the hook

The hook is used to hang up the power tool to your

waist belt while working.

CAUTION:

䡬 When using the hook, hang up the power tool firmly

not to drop accidentally.

If the power tool is dropped, it may lead to an accident.

䡬 When carrying the power tool hooked to your waist

belt, do not fit any bit to the tip of power tool. If the

sharp bit such as drill is fitted to the power tool when

carrying it hooked to your waist belt, you will be

injured.

䡬 Install securely the hook. Unless the hook is securely

installed, it may cause an injury while being used.

(1) Removing the hook.

Remove the screws fixing the hook with Philips screw

driver. (Fig. 7)

(2)

Replacing the hook and tightening the screws.

Install securely the hook in the groove of power tool

and tighten the screws to fix the hook firmly. (Fig. 8)

6. About Remaining Battery Indicator

When pressing the remaining battery indicator switch,

the remaining battery indicator lamp lights and the

battery remaining power can be checked. (Fig. 9)

When releasing your finger from the remaining

battery indicator switch, the remaining battery

indicator lamp goes off. The Table 4 shows the state

of remaining battery indicator lamp and the battery

remaining power.

As the remaining battery indicator shows somewhat

differently depending on ambient temperature and

battery characteristics, read it as a reference.

NOTE:

䡬 Do not give a strong shock to the switch panel or

break it. It may lead to a trouble.

䡬 To save the battery power consumption, the

remaining battery indicator lamp lights while pressing

the remaining battery indicator switch.

7. How to use the LED light

Every time you press the light switch on the switch

panel, the LED light lights or goes off. (Fig. 10)

To prevent the battery power consumption, turn off

the LED light frequently.

CAUTION:

䡬 Do not expose directly your eyes to the light by

looking into the light.

If your eyes are continuously exposed to the light,

your eyes will be hurt.

Electronic pulse mode, self drilling

screw mode (2) and drill mode

Self drilling screw

mode (1)

Bolt mode

Electronic clutch mode

(reverse rotation)

Electronic clutch mode

(regular rotation)

Rotation speed

Elapsed time after switching on

State of lamp Battery Remaining Power

The battery remaining power

is enough.

The battery remaining power

is a half.

The battery remaining power

is nearly empty.

Re-charge the battery soonest

possible.

Table 4

01Eng_WM14DBL_ EE 9/27/10, 9:0413

Содержание

Похожие устройства

English On the other hand the electronic clutch mode reverse rotation meets the preset rotation speed immediately after the start Elapsed time after switching on O The tool may not return to the initial status from the striking operation When the bit or socket is removed from the screw or bolt while the switch is being pulled the tool may continue the striking operation To return to the initial status turn off the switch and then start the next operation O Motor rotation speed does not decrease even when the remaining battery power becomes low Since this tool adopts the constant speed control the rotation speed is almost unchanged even when the remaining amount of the battery becomes low This allows users to operate the tool efficiently until the battery runs down However it is difficult to know the remaining battery power from the rotation speed and the tool may stop suddenly during work Check the remaining battery power by pressing the remaining battery indicator switch at times 3 Check the rotational direction The bit rotates clockwise viewed from the rear side by pushing the R side of the push button The L side of the push button is pushed to turn the bit counterclockwise See Fig 6 The L and TO marks are provided on the body CAUTION The push button can not be switched while the tool is turning To switch the push button stop the tool then set the push button 4 Switch operation O When the trigger switch is depressed the tool rotates When the trigger is released the tool stops O The rotati onal speed can be controlled by varying the amount that the trigger switch is pulled Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more 5 Using the hook The hook is used to hang up the power tool to your waist belt while working 13 CAUTION O When using the hook hang up the power tool firmly not to drop accidentally If the power tool is dropped it may lead to an accident O When carrying the power tool hooked to your waist belt do not fit any bit to the tip of power tool If the sharp bit such as drill is fitted to the power tool when carrying it hooked to your waist belt you will be injured O Install securely the hook Unless the hook is securely installed it may cause an injury while being used 1 Removing the hook Remove the screws fixing the hook with Philips screw driver Fig 7 2 Replacing the hook and tightening the screws Install securely the hook in the groove of power tool and tighten the screws to fix the hook firmly Fig 8 6 About Remaining Battery Indicator When pressing the remaining battery indicator switch the remaining battery indicator lamp lights and the battery remaining power can be checked Fig 9 When releasing your finger from the remaining battery indicator switch the remaining battery indicator lamp goes off The Table 4 shows the state of remaining battery indicator lamp and the battery remaining power Table 4 State of lamp 1 I a Battery Remaining Power The battery remaining power is enough The battery remaining power is a half The battery remaining power is nearly empty Re charge the battery soonest possible As the remaining battery indicator shows somewhat differently depending on ambient temperature and battery characteristics read it as a reference NOTE O Do not give a strong shock to the switch panel or break it It may lead to a trouble O To save the battery power consumption the remaining battery indicator lamp lights while pressing the remaining battery indicator switch 7 How to use the LED light Every time you press the light switch on the switch panel the LED light lights or goes off Fig 10 To prevent the battery power consumption turn off the LED light frequently CAUTION O Do not expose directly your eyes to the light by looking into the light If your eyes are continuously exposed to the light your eyes will be hurt

Скачать