Home
Главная
Hitachi
Аккумуляторный Шуруповерт
DS12DVF3
Инструкция по эксплуатации Страница: 16

Hitachi DS12DVF3 [16/96] English

English

(b) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly (Fig. 20).

the protuberance of the hook cover, press the hook

cover in the direction opposite to that of the arrow

shown in Fig. 19 and then tighten the screw.

Use commercially available AAAA batteries (1.5 V).

NOTE

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION

䡬 Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals correctly.

Replace both batteries at the same time. Do not mix

old and new batteries.

Remove exhausted batteries from the hook

immediately.

䡬 Do not discard batteries together with normal trash

and do not throw batteries into fire.

䡬 Store batteries out of the reach of children.

䡬 Use batteries correctly in accordance with the battery

specifications and indications.

11. Using the bit holder

CAUTION

䡬 Stow the bit in the specified location on the tool.

If the tool is used with the bit stowed improperly,

the bit may fall and cause bodily injury.

䡬 Do not stow bits that are of a different length,

gauge or dimension than the plus driver bit (65 mm

long) included in the STANDARD ACCESSORIES.

The bit may fall and cause bodily injury.

(1) Removing the bit

Securely hold the main unit and pull out the bit

by holding the tip with your thumb (Fig. 21).

(2) Installing the Bit

Install the bit with steps opposite of when removing.

Insert the bit so that the right and left sides are

equal, as shown in Fig. 22.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or

replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Cleaning on the outside

When the driver drill is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water.

Do not use chloric solvents, gasoline or paint thinner,

for they melt plastics.

4. Storage

Store the driver drill in a place in which the temperature

is less than 40°C and out of reach of children.

5. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee

does not cover defects or damage due to misuse, abuse,

or normal wear and tear. In case of complaint, please

send the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

<DS9DVF3, DS12DVF3>

Measured A-weighted sound power level: 74 dB (A)

Measured A-weighted sound pressure level: 63 dB (A)

Uncertainty KpA: 3 dB (A).

<DS14DVF3, DS18DVF3>

Measured A-weighted sound power level: 80 dB (A)

Measured A-weighted sound pressure level: 69 dB (A)

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

As drill:

Vibration emission value

ah, D

= 0.9 m/s

(DS9DVF3)

1.5 m/s

(DS12DVF3)

1.6 m/s

(DS14DVF3)

1.8 m/s

(DS18DVF3)

Uncertainty K = 1.5 m/s

WARNING

䡬 The vibration emission value during actual use of

the power tool can differ from the declared value

depending on the ways in which the tool is used.

䡬 To identify the safety measures to protect the

operator that are based on an estimation of exposure

in the actual conditions of use (taking account of

all parts of the operating cycle such as the times

when the tool is switched off and when it is running

idle in addition to the trigger time).

01Eng_DS9DVF3_EE 1/20/09, 16:0015

Содержание

Похожие устройства

English b Remove the old batteries and insert the new batteries Align with the hook indications and position the plus and minus terminals correctly Fig 20 c Align the indentation in the hook main body with the protuberance of the hook cover press the hook cover in the direction opposite to that of the arrow shown in Fig 19 and then tighten the screw Use commercially available AAAA batteries 1 5 V NOTE Do not tighten the screw excessively Such action could strip the screw threads CAUTION O Failure to observe the following can result in battery leakage rust or malfunction Position the plus and minus terminals correctly Replace both batteries at the same time Do not mix old and new batteries Remove exhausted batteries from the hook immediately O Do not discard batteries together with normal trash and do not throw batteries into fire O Store batteries out of the reach of children O Use batteries correctly in accordance with the battery specifications and indications 11 Using the bit holder CAUTION O Stow the bit in the specified location on the tool If the tool is used with the bit stowed improperly the bit may fall and cause bodily injury O Do not stow bits that are of a different length gauge or dimension than the plus driver bit 65 mm long included in the STANDARD ACCESSORIES The bit may fall and cause bodily injury 1 Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb Fig 21 2 Installing the Bit Install the bit with steps opposite of when removing Insert the bit so that the right and left sides are equal as shown in Fig 22 MAINTENANCE AND INSPECTION 1 Inspecting the tool Since use of as dull tool will degrade efficiency and cause possible motor malfunction sharpen or replace the tool as soon as abrasion is noted 2 Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screws be loose retighten them immediately Failure to do so could result in serious hazard 3 Cleaning on the outside When the driver drill is stained wipe with a soft dry cloth or a cloth moistened with soapy water Do not use chloric solvents gasoline or paint thinner for they melt plastics 4 Storage Store the driver drill in a place in which the temperature is less than 40 C and out of reach of children 5 Service parts list CAUTION Repair modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center 15 This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance In the operation and maintenance of power tools the safety regulations and standards prescribed in each country must be observed MODIFICATIONS Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements Accordingly some parts may be changed without prior notice GUARANTEE We guarantee Hitachi Power Tools in accordance with statutory country specific regulation This guarantee does not cover defects or damage due to misuse abuse or normal wear and tear In case of complaint please send the Power Tool undismantled withthe GUARANTEE CERTIFICATE foundattheendof this Handling instruction to a Hitachi Authorized Service Center NOTE Due to HITACHI S continuing program development the specifications herein change without prior notice Information concerning airborne of research and are subject to noise and vibration The measured values were determined according EN60745 and declared in accordance with ISO 4871 to DS9DVF3 DS12DVF3 Measured A weighted sound power level 74 dB A Measured A weighted sound pressure level 63 dB A 69 dB A Uncertainty KpA 3 dB A DS14DVF3 DS18DVF3 Measured A weighted sound power level 80 dB A Measured A weighted sound pressure level Uncertainty KpA 3 dB A Wear hearing protection Vibration total values according to EN60745 triax vector sum determined As drill Vibration emission value 3h D 0 9 m s2 DS9DVF3 1 5 m s2 DS12DVF3 1 6 m s2 DS14DVF3 1 8 m s2 DS18DVF3 Uncertainty K 1 5 m s2 WARNING O The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used O To identify the safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time

Скачать

Случайные обсуждения

Ответы 1

электосхема

8 лет назад

Ответы 1

Назначение переключателя "low and high"?

7 лет назад

Ответы 0

Не могу скрутить, маленькая железка выросла, а я не заметил откуда.

4 года назад

Ответы 1