Home
Главная
Hitachi
Аккумуляторная Дрель-Шуруповерт
DV18DCL2
Инструкция по эксплуатации Страница: 9

Hitachi DV18DCL2 [9/92] English

English

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically designated

battery packs.

Use of any other battery packs may create a risk

of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach of

children and infirm persons.

PRECAUTIONS FOR CORDLESS IMPACT DRIVER

DRILL

1. Always charge the battery at a temperature of 0 –

50°C. A temperature of less than 0°C will result

in over charging which is dangerous. The battery

cannot be charged at a temperature higher than

50°C.

The most suitable temperature for charging is that

of 20 – 25°C.

2. When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

Do not charge more than two batteries

consecutively.

3. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

4. Never disassemble the rechargeable battery and

charger.

5. Never short-circuit the rechargeable battery. Short-

circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

6. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

7. When drilling in wall, floor or ceiling, check for

buried electric power cord, etc..

8. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

9. Using an exhausted battery will damage the

charger.

10. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

11. When mounting a bit into the keyless chuck, tighten

the sleeve adequately. If the sleeve is not tight,

the bit may slip or fall out, causing injury.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 to 3 described below, when using

this product, even if you are pulling the switch, the

motor may stop. This is not the trouble but the result

of protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

3. If the battery is overheated under overload work,

the battery power may stop.

In this case, stop using the battery and let the

battery cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

䡬 During work make sure that swarf and dust do

not fall on the battery.

䡬 Make sure that any swarf and dust falling on the

power tool during work do not collect on the

battery.

䡬 Do not store an unused battery in a location

exposed to swarf and dust.

䡬 Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such

as a nail, strike with a hammer, step on, throw

or subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

7. If the battery charging fails to complete even

when a specified recharging time has elapsed,

immediately stop further recharging.

8. Do not put or subject the battery to high

temperatures or high pressure such as into a

microwave oven, dryer, or high pressure container.

9. Keep away from fire immediately when leakage

or foul odor are detected.

01Eng_DV14DCL2_EE 12/4/09, 4:238

Содержание

Похожие устройства

English 5 Battery tool use and care a Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack b Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire c When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire d Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritation or burns 6 Service a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained PRECAUTION Keep children and infirm persons away When not in use tools should be stored out of reach of children and infirm persons PRECAUTIONS FOR CORDLESS IMPACT DRIVER DRILL 1 Always charge the battery at a temperature of 0 50 C A temperature of less than 0 C will result in over charging which is dangerous The battery cannot be charged at a temperature higher than 50 C The most suitable temperature for charging is that of 20 25 C 2 When one charging is completed leave the charger for about 15 minutes before the next charging of battery Do not charge more than two batteries consecutively 3 Do not allow foreign matter to enter the hole for connecting the rechargeable battery 4 Never disassemble the rechargeable battery and charger 5 Never short circuit the rechargeable battery Short circuiting the battery will cause a great electric current and overheat It results in burn or damage to the battery 6 Do not dispose of the battery in fire If the battery is burnt it may explode 7 When drilling in wall floor or ceiling check for buried electric power cord etc 8 Bring the battery to the shop from which it was purchased as soon as the post charging battery life becomes too short for practical use Do not dispose of the exhausted battery 9 Using an exhausted battery will damage the charger 10 Do not insert object into the air ventilation slots of the charger Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger 11 When mounting a bit into the keyless chuck tighten the sleeve adequately If the sleeve is not tight the bit may slip or fall out causing injury CAUTION ON LITHIUM ION BATTERY To extend the lifetime the lithium ion battery equips with the protection function to stop the output In the cases of 1 to 3 described below when using this product even if you are pulling the switch the motor may stop This is not the trouble but the result of protection function 1 When the battery power remaining runs out the motor stops In such case charge it up immediately 2 If the tool is overloaded the motor may stop In this case release the switch of tool and eliminate causes of overloading After that you can use it again 3 If the battery is overheated under overload work the battery power may stop In this case stop using the battery and let the battery cool After that you can use it again Furthermore please heed the following warning and caution WARNING In order to prevent any battery leakage heat generation smoke emission explosion and ignition beforehand please be sure to heed the following precautions 1 Make sure that swarf and dust do not collect on the battery O During work make sure that swarf and dust do not fall on the battery O Make sure that any swarf and dust falling on the power tool during work do not collect on the battery O Do not store an unused battery in a location exposed to swarf and dust O Before storing a battery remove any swarf and dust that may adhere to it and do not store it together with metal parts screws nails etc 2 Do not pierce battery with a sharp object such as a nail strike with a hammer step on throw or subject the battery to severe physical shock 3 Do not use an apparently damaged or deformed battery 4 Do not use the battery in reverse polarity 5 Do not connect directly to an electrical outlets or car cigarette lighter sockets 6 Do not use the battery for a purpose other than those specified 7 If the battery charging fails to complete even when a specified recharging time has elapsed immediately stop further recharging 8 Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven dryer or high pressure container 9 Keep away from fire immediately when leakage or foul odor are detected 8

Скачать