![Aten VM5808HA [40/124] Profile pushbutton](/img/pdf.png)
Aten VM5808HA [40/124] Profile pushbutton
![Aten VM5808HA [40/124] Profile pushbutton](/views2/1977702/page40/bg28.png)
VM5404HA / VM5808HA User Manual
28
Profile Pushbutton
The PROFILE pushbutton lets users conveniently switch between connection
profiles that have been saved or added to the Profile List (see Profile List,
page 31).
When a Profile is in use, its profile number (P1–P16) is shown on the lower
right corner of the LCD display.
The Profile pushbutton functions as follows:
After pressing the Profile pushbutton, available profile numbers will light
up. The active profile number will flash. use the Input/Output pushbuttons
to switch to a specific profile (P1 to P16) or (P1 to P8). Note that:
Input ports 1–8 or 1-4 correspond to Profile P1 to P8 or P1 to P4
Output ports 1–8 or 1-4 correspond to Profile P9 to P16 or P5 to P8
(where Output Port 1=Profile 9, Output Port 2=Profile 10... Output
Port 8=Profile 16)
The selected pushbutton’s light flashes, and the VM5404HA /
VM5808HA immediately applies the port connections configured in the
selected profile. If the light changes to a steady state, it means the profile is
valid.
After pressing the Profile pushbutton, pressing it again will change to next
profile in Profile Scheduling (see page 37), not the profile list. This feature
is only available while a schedule is playing.
Press the Cancel pushbutton to exit
Note: If there are no profiles configured on the VM5404HA / VM5808HA
device, an error message “No Available Profile” is displayed when the
Profile pushbutton is pressed.
A Profile’s port connections can be edited using the front panel pushbuttons
(see Port Switching, page 11) or from the Connections page of the Browser
GUI (see Configuring Video Settings of a Profile, page 39). Additionally, the
Profile List can be configured via the Profile page of the Browser GUI (see
Profile List, page 31).
INPUT 1 2 5 5 1 1 3 4
OUTPUT 1 2 3 4 5 6 7 8
P1
Содержание
- Vm5404ha vm5808ha 1
- Compliance statements 2
- Online registration 4
- Telephone support 4
- User information 4
- User notice 4
- Package contents 5
- Product information 5
- Contents 6
- Front panel configuration 6
- Hardware setup 6
- Introduction 6
- Browser operation 7
- Cli commands 8
- Appendix 9
- About this manual 10
- Conventions 11
- Terminology 11
- This manual uses the following conventions 11
- This page intentionally left blank 12
- Chapter 1 13
- Introduction 13
- Overview 13
- Features 14
- Cables 15
- Display devices 15
- Requirements 15
- Source devices 15
- Supported browsers 16
- Use the recommended web browsers below to access the vm5404ha vm5808ha s web console 16
- Components 17
- Chapter 2 19
- Hardware setup 19
- Rack mounting 19
- Installation 20
- Chapter 3 21
- Front panel configuration 21
- Front panel pushbuttons 21
- Overview 21
- Enter password 22
- Input port selection 23
- Main screen 23
- Port switching 23
- Output port selection 25
- Lcd menu organization 26
- Note the highlighted values are the default settings of the vm5404ha 26
- The vm5404ha vm5808ha has a built in configuration utility via the front panel lcd which can be controlled by pressing the menu and front panel input pushbuttons 1 8 or 1 4 user can cycle through the menu options starting from ip setting page in the order shown in the table below 26
- Vm5404ha vm5808ha user manual 26
- Vm5808ha 26
- Ip address subnet mask 27
- Ip setting 27
- Menu pushbutton 27
- Gateway 28
- Serial port setting 29
- Edid mode 30
- Operation mode 30
- Output status 33
- Array mode local hdmi out 35
- Security mode 36
- Change password 37
- Save to a profile 38
- Play stop the profile schedule 39
- Turn video wall off 39
- Profile pushbutton 40
- Browser operation 41
- Chapter 4 41
- Logging in 41
- Overview 41
- Main page 42
- Menu bar 42
- Adding playing a profile 43
- Profile list 43
- Deleting a profile 45
- Exporting a profile 45
- Importing a profile 45
- Clicking a profile or the play window opens a pop up menu with options 47
- Play window 47
- Profile 47
- Profile list options 47
- Profile scheduling 49
- Profile scheduling is located below the profile list scheduling allows you to queue and play connection profiles in sequence for a specific amount of time 49
- After selecting edit you will be presented with the following options 50
- Configuring video settings of a profile 51
- Configuring video settings in normal view 54
- Profile layout settings 54
- Display preferences 56
- Blank output 58
- Independent output 58
- Grouping 59
- Configuring video settings in grid view 61
- In the web console click the settings icon from the main page for the system settings to open on the general page 62
- System settings 62
- The table below provides an overview of the available settings for each tab 62
- General 64
- Port settings 65
- Port name 69
- Edid settings 70
- Status 87
- Maintenance 89
- Chapter 5 95
- Cli commands 95
- Connecting to the matrix switch via telnet 95
- Overview 95
- Connect the rs 232 serial port on the vm5404ha vm5808ha to the rs 232 serial port on your computer using a 9 wire straight cable with only pin 2 to pin 2 pin 3 to pin 3 and pin 5 to pin 5 connected 96
- Connecting to the matrix switch via rs 232 96
- The controller s serial port should be configured as follows 96
- When a session is established with the vm5404ha vm5808ha you can control and configure the vm5404ha vm5808ha via rs 232 commands for more information on commands see commands page 85 96
- You can control and operate the vm5404ha vm5808ha using a high end controller or pc to connect to the vm5404ha vm5808ha via rs 232 do the following 96
- Command verification 97
- Commands 97
- Switch port command 97
- All output ports 98
- Control description 98
- Each command string can be separated with a space 98
- Next port 98
- Note 1 by default input port 01 is tied to output port 01 input port 02 is tied to output port 02 and so on until port 08 i e o01 i01 o02 i02 98
- O output command 98
- Off turn off the display 98
- On turn on the display 98
- Output command description 98
- Port number description 98
- Previous port 98
- The following table lists the available switch port commands 98
- The port number can be skipped and the default value will be used 98
- Vm5404ha vm5808ha user manual 98
- Yy 01 08 port 98
- Command control enter 99
- Edid mode command 99
- Edid port1 enter 99
- Extended display identification data edid is a data that contains a display s basic information and is used to communicate with the video source 99
- For example to use the port1 edid mode type 99
- Note each command string can be separated with a space 99
- The following table lists the available edid commands 99
- The following tables show the possible values for the edid command 99
- The formula for the edid command is as follows 99
- Command output number control enter 100
- For example to mute the audio coming from output port 1 type 100
- Mute allows you to enable or disable an output port s audio 100
- Mute command 100
- Mute o01 on enter 100
- Note 1 each command string can be separated with a space 100
- Output ports 100
- Skip the output port command to mute or enable the audio of all 100
- The following table lists the available mute commands 100
- The following tables show the possible values for the mute command 100
- The formula for the mute command is as follows 100
- Cec command 101
- Cec o01 on enter 101
- Command output number control enter 101
- Consumer electronics control cec allows interconnected hdmi devices to communicate and respond to the same remote control 101
- For example to enable the cec function on output port 1 type 101
- Note each command string can be separated with a space 101
- The following table lists the available cec commands 101
- The following tables show the possible values for the cec command 101
- The formula for the cec command is as follows 101
- Command output number 1 horizontal resolution number 2 vertical resolution number 3 frequency number 4 control enter 102
- For example to turn scaling off for output port 02 type 102
- Scaling command 102
- Scaling o native enter 102
- Scaling o02 off enter 102
- Scaling o04 1080p enter 102
- The following tables show the possible values for the scaling command 102
- The formula for the scaling command is as follows 102
- The scaling command allows you to set a resolution for scaling the display connected to an output port 102
- To set the scaling for all output ports to the connected display s native resolution type 102
- To set the scaling for output port 04 to 1920x1080 60hz type 102
- By pass mode 103
- Chapter 5 cli commands 103
- Control description 103
- Fff frequency resolution 103
- Freq frequency command for scaling 103
- Frequency description 103
- Frequency number description 103
- Native map display s native resolution for scaling default 103
- Note 1 each command string can be separated with a space 103
- Off turn off the scaling function 103
- Resolution number description 103
- The following table lists the available scaling commands 103
- The port number command string can be skipped and the default 103
- Value will be used 103
- Vvvv vertical resolution 103
- Vm5404ha vm5808ha user manual 104
- Command control enter 105
- Fan low enter 105
- Fan speed command 105
- For example to set the fan to low speed type 105
- Note each command string can be separated with a space 105
- The fan speed command allows you to set the internal fan speed that cools the vm5404ha vm5808ha 105
- The following table lists the available fan speed commands 105
- The following tables show the possible values for the fan speed command 105
- To set the fan speed use the following command 105
- Command control enter 106
- Echo command 106
- Echo on enter 106
- For example to enable the echo feature type 106
- Note each command string can be separated with a space 106
- The echo function updates the rs 232 controller when operations are made via the front panel pushbuttons web browser or telnet the changes echo back to the rs 232 controller to keep the settings in sync with the device 106
- The following table lists the available echo commands 106
- The following tables show the possible values for the echo comman 106
- The formula for the echo command is as follows 106
- Black screen command 107
- Blackscreen on enter 107
- Command control enter 107
- For example to enable the black screen function type 107
- Note each command string can be separated with a space 107
- The black screen command turns a display screen black when no source signal is detected this prevents the display from showing the default blue or other color used when no source signal is detected 107
- The following table lists the available black screen commands 107
- The following tables show the possible values for the black screen comman 107
- The formula for the black screen command is as follows 107
- Read command 108
- Reset command 108
- Baud 38400 enter 109
- Baud rate command 109
- Command control enter 109
- For example to set 38400 as the baud rate type 109
- Note each command string can be separated with a space 109
- The baud rate command allows you to set the rs 232 data rate for the vm5404ha vm5808ha to use options are 9600 19200 default 38400 and 115200 109
- The following table lists the available baud rate commands 109
- The following tables show the possible values for the baud rate command 109
- The formula for the baud rate command is as follows 109
- Command profile number control enter 110
- For example to save the current connection configuration to profile 02 type 110
- Note each command string can be separated with a space 110
- Profile f 02 save enter 110
- Save load profile command 110
- The following table lists the available save load profile commands 110
- The following tables show the possible values for the save load profile commands 110
- The formula for the save load profile command is as follows 110
- The save load profile command allows you to save and load connection profiles saving profiles will save the connections currently in use 110
- Command output number control enter 111
- For example to disable the osd for all outputs type 111
- For example to enable the osd for output 07 type 111
- Note each command string can be separated with a space 111
- Osd command 111
- Osd o off enter 111
- Osd o07 on enter 111
- The following table lists the available osd commands 111
- The following tables show the possible values for the osd command 111
- To enable or disable the on screen display osd for displays use the following command 111
- Array command 112
- Array ver 1 hor 1 i8 enter 112
- Array ver 2 hor 2 i7 8 2 3 enter 112
- Array ver 8 hor 1 enter 112
- Command vertical number horizontal number input sequence enter 112
- For example to set up a single view with video from input port 8 type 112
- For example to set up the viewing mode to a 2x2 array with video inputs from input port 7 8 2 and 3 sequentially type 112
- For example to set up the viewing mode to a 8x1 array with all 8 video inputs type 112
- The following tables show the possible values for the array command 112
- To set up an viewing mode 1x1 1x2 2x2 or 4x1 vm5404ha only 8x1 vm5808ha only for the local display use the following command 112
- Note 1 each command string should be separated with a space 113
- The following table lists the available array commands 113
- The viewing array supports modes of 1x1 single 1x2 side by side 2x2 quad mode or 4x1 vm5404ha only and 8x1 vm5808ha only show all only 113
- Use commas to separate the input ports when setting the input sequence the input sequence can be omitted in the 4x1 and 8x1 mode which all 4 and 8 input ports will show on the local screen 113
- Alert command 114
- Alert i01 m1 enter 114
- Command input number control enter 114
- For example to enable the basic alert function for input port 1 type 114
- Note each command string can be separated with a space 114
- The following table lists the available alert commands 114
- The following tables show the possible values for the alert command 114
- To trigger a warning when issues arise for a specific input port use the following command 114
- Appendix 115
- General 115
- Safety instructions 115
- Rack mounting 117
- International 118
- North america 118
- Technical support 118
- Specifications 119
- Configuration menu 121
- Telnet operation 121
- Aten standard warranty policy 124
- Limited hardware warranty 124
Похожие устройства
- Aten VM5404HA Краткое руководство по установке
- Aten VM5404HA Руководство пользователя
- Aten VM6404HB Краткое руководство по установке
- Aten VM6404HB Руководство видеоматрицы
- Aten VM6404HB Руководство пользователя
- Aten VM6809H Краткое руководство по установке
- Aten VM6809H Руководство пользователя
- Aten VM51616H Руководство к видеоматрице
- Aten VM51616H Руководство к приложению контроля видеоматрицы
- Aten VM51616H Руководство пользователя
- Aten VM3250 Руководство пользователя
- Aten VM3250 Руководство к видеоматрице
- Aten VM3250 Краткое руководство по установке
- Aten VM3250 Руководство к приложению для контроля видеоматрицы
- Aten VM7824 Краткое руководство по установке
- Aten VM8824 Краткое руководство по установке
- Aten VM7584 Краткое руководство по установке
- Aten VM8584 Краткое руководство по установке
- Aten VM7904 Краткое руководство по установке
- Aten VM7814 Краткое руководство по установке