![Epson L800 [16/105] L800 l801 revision a](/img/pdf.png)
Epson L800 [16/105] L800 l801 revision a
![Epson L800 [16/105] How to unlock the carriage](/views2/1131806/page16/bg10.png)
L800/L801 Revision A
Disassembly/Reassembly Overview 16
Confidential
1.1.5 Orientation Definition
Orientation descriptions used in the disassembly/reassembly procedures are as
follows.
Figure 1-12. Orientation Definition
1.1.6 How to Unlock the Carriage
Unlocking the carriage is required for disassembly of some parts or
components. Carry out any of the following operations to unlock the carriage
and move the carriage to other than its home position.
Power the printer and turn it off forcedly by disconnecting the power cable
when the CR Unit is unlocked and moved away from the home position.
Turn the EJ Roller gear on the left side of the printer in the direction of the
arrow until the carriage is unlocked.
Figure 1-13. How to Unlock the Carriage
[Left Side] [Right (home) Side]
[Rear Side]
[Front Side]
C A U T I O N
Be extremely careful not to damage the EJ Roller gear. Extra care
must be taken to avoid injury from sharp metal edges.
Carriage Lock
Locked
Carriage Lock
Unlocked
[Left side]
PF Roller Gear
EJ Roller Gear
Turn this gear
Содержание
- L800 l801 1
- Service manual 1
- Confidential 2
- Copyright 2
- Epson is a registered trademark of seiko epson corporation 2
- Note other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their respective owners epson dis claims any and all rights in those marks 2
- Notice 2
- Seiko epson corporation i i cs quality assurance department 2
- Danger 3
- Safety precautions 3
- Warning 3
- Precautions 4
- About this manual 5
- Chapter 1 disassembly reassembly 5
- Chapter 2 adjustment 5
- Chapter 3 maintenance 5
- Chapter 4 appendix 5
- Manual configuration 5
- Symbols used in this manual 5
- A april 6 2011 first release 6
- Confidential 6
- Revision status 6
- Chapter 1 disassembly reassembly 7
- Chapter 2 adjustment 7
- Confidential 7
- Contents 7
- L800 l801 revision a 7
- Chapter 3 maintenance 8
- Chapter 4 appendix 8
- Confidential 8
- L800 l801 revision a 8
- C h a p t e r 9
- Disassembly reassembly 9
- Checks and precautions before disassembling 10
- Factors which affect the print quality 10
- Overview 10
- Factors which affect the safety of service personnel such as ink leakage during operation 11
- Adapter is removed 12
- Before disconnecting the joint parts of the ink path make sure that the adapter is removed from the carriage 12
- Confidential 12
- Disassembly reassembly overview 12 12
- Discharging ink is recommended only when disconnecting the ink supply tank tube assy from the ink supply tank before performing the above disconnection discharge ink from the ink supply tank as follows 12
- Figure 1 4 adapter 12
- L800 l801 revision a 12
- The adapter has an ink valve which cuts off the ink path when removing the adapter from the carriage 12
- Confidential 13
- Disassembly reassembly overview 13 13
- L800 l801 revision a 13
- Protection for transportation 14
- Can be easily removed by using a special tool the method for making the tool is described below 15
- Confidential 15
- Disassembly reassembly overview 15 15
- L800 l801 revision a 15
- Making a special tool for holder contact 15
- Points to be checked before packing the printer 15
- The holder contact refer to 15
- Be extremely careful not to damage the ej roller gear extra care must be taken to avoid injury from sharp metal edges 16
- Confidential 16
- Disassembly reassembly overview 16 16
- Figure 1 12 orientation definition 16
- Figure 1 13 how to unlock the carriage 16
- How to unlock the carriage 16
- L800 l801 revision a 16
- Orientation definition 16
- Orientation descriptions used in the disassembly reassembly procedures are as follows 16
- Power the printer and turn it off forcedly by disconnecting the power cable when the cr unit is unlocked and moved away from the home position 16
- Turn the ej roller gear on the left side of the printer in the direction of the arrow until the carriage is unlocked 16
- Unlocking the carriage is required for disassembly of some parts or components carry out any of the following operations to unlock the carriage and move the carriage to other than its home position 16
- Confidential 17
- Disassembly reassembly disassembly reassembly procedures 17 17
- Disassembly reassembly procedures 17
- Figure 1 14 example chart 17
- L800 l801 revision a 17
- Overview 17
- Table 1 2 explanatory note 17
- The example below shows how to see the charts on the following pages 17
- This section describes procedures for disassembling the parts units in a flowchart format for some parts units detailed procedures or precautions are provided accordingly indicated by icons and cell s color refer to the explanations in the example chart below and perform an appropriate disassembling and reassembling procedure see 1 removing exterior parts components p24 17
- 1 housing upper assy p25 18
- 1 printhead p37 18
- 1 stacker assy stacker cover p25 18
- Confidential 18
- Disassembly flowchart 18
- Disassembly reassembly disassembling reassembling flowchart 18 18
- L800 l801 revision a 18
- Screw type torque list 18
- 1 apg unit p41 19
- 1 panel assy cover open sensor p30 19
- Confidential 19
- Disassembly reassembly disassembling reassembling flowchart 19 19
- L800 l801 revision a 19
- Screw type torque list 19
- Symbol screw type torque 19
- 1 0 pf encoder pf scale p49 20
- 1 6 apg sensor assy p57 20
- 1 main board unit p27 20
- Confidential 20
- Disassembly reassembly disassembling reassembling flowchart 20 20
- L800 l801 revision a 20
- Screw type torque list 20
- Symbol screw type torque 20
- There are four tube holders installed in this printer depending on the target parts or units the number of tube holders you should remove differs 20
- When removing the ink supply tank assy the tube holder on the home position side on the cover case when removing the printer mechanism all tube holders 20
- 1 2 cr motor p50 21
- 1 left right guide stackers cdr guide sensor p44 21
- 1 waste ink pad lower waste ink pad cap lower p43 21
- Confidential 21
- Disassembly reassembly disassembling reassembling flowchart 21 21
- L800 l801 revision a 21
- P 20 p 21 21
- Screw type torque list 21
- 1 3 cr unit p52 22
- 1 4 asf unit p54 22
- 1 ink system p45 1 ej frame assy p46 22
- Confidential 22
- Disassembly reassembly disassembling reassembling flowchart 22 22
- L800 l801 revision a 22
- Screw type torque list 22
- Symbol screw type torque 22
- 1 4 asf unit p54 23
- 1 7 front paper guide assy p57 23
- Confidential 23
- Disassembly reassembly disassembling reassembling flowchart 23 23
- L800 l801 revision a 23
- Screw type torque list 23
- Symbol screw type torque 23
- Confidential 24
- Disassembly reassembly printer cover 24 24
- L800 l801 revision a 24
- Paper support assy 24
- Printer cover 24
- Removing exterior parts components 24
- Confidential 25
- Disassembly reassembly stacker assy stacker cover 25 25
- Housing upper assy 25
- L800 l801 revision a 25
- Stacker assy stacker cover 25
- Confidential 26
- Disassembly reassembly housing upper assy 26 26
- L800 l801 revision a 26
- Confidential 27
- Disassembly reassembly main board unit 27 27
- Figure 1 23 connector layout of the main board 27
- Figure 1 24 removing the main board unit 1 27
- L800 l801 revision a 27
- Main board unit 27
- Main board unit removal 1 disconnect all connectors on the main board unit 2 peel off the double sided tape that secures the panel ffc to the holder frame and release the panel ffc fig 29 p 0 27
- Peel off the four acetate tapes that secures the following cables on the back of the main board unit 27
- Removal procedure 27
- Removing control boards 27
- Table 1 3 list of connectors and their destinations 27
- Confidential 28
- Disassembly reassembly main board unit 28 28
- L800 l801 revision a 28
- Confidential 29
- Disassembly reassembly main board unit 29 29
- L800 l801 revision a 29
- Confidential 30
- Disassembly reassembly panel assy cover open sensor 30 30
- L800 l801 revision a 30
- Panel assy cover open sensor 30
- Confidential 31
- Disassembly reassembly panel assy cover open sensor 31 31
- L800 l801 revision a 31
- Confidential 32
- Disassembly reassembly panel assy cover open sensor 32 32
- L800 l801 revision a 32
- Confidential 33
- Disassembly reassembly panel assy cover open sensor 33 33
- L800 l801 revision a 33
- Confidential 34
- Disassembly reassembly p s assy 34 34
- L800 l801 revision a 34
- P s assy 34
- Confidential 35
- Disassembling the printer mechanism 35
- Disassembly reassembly removing the printer mechanism 35 35
- L800 l801 revision a 35
- Removing the printer mechanism 35
- Confidential 36
- Disassembly reassembly removing the printer mechanism 36 36
- L800 l801 revision a 36
- Confidential 37
- Disassembly reassembly printhead 37 37
- L800 l801 revision a 37
- Printhead 37
- Confidential 38
- Disassembly reassembly printhead 38 38
- L800 l801 revision a 38
- Confidential 39
- Disassembly reassembly printhead 39 39
- L800 l801 revision a 39
- Confidential 40
- Cr scale 40
- Disassembly reassembly cr scale 40 40
- L800 l801 revision a 40
- Apg unit 41
- Confidential 41
- Disassembly reassembly apg unit 41 41
- L800 l801 revision a 41
- Confidential 42
- Disassembly reassembly waste ink tray 42 42
- L800 l801 revision a 42
- Waste ink tray 42
- Confidential 43
- Disassembly reassembly waste ink pad lower waste ink pad cap lower 43 43
- L800 l801 revision a 43
- Waste ink pad lower waste ink pad cap lower 43
- Confidential 44
- Disassembly reassembly left right guide stackers cdr guide sensor 44 44
- L800 l801 revision a 44
- Left right guide stackers cdr guide sensor 44
- Confidential 45
- Disassembly reassembly ink system 45 45
- Ink system 45
- L800 l801 revision a 45
- Confidential 46
- Disassembly reassembly ej frame assy 46 46
- Ej frame assy 46
- L800 l801 revision a 46
- Confidential 47
- Disassembly reassembly ej frame assy 47 47
- L800 l801 revision a 47
- Confidential 48
- Disassembly reassembly ej frame assy 48 48
- L800 l801 revision a 48
- Confidential 49
- Disassembly reassembly pf encoder pf scale 49 49
- L800 l801 revision a 49
- Pf encoder pf scale 49
- Pf motor 49
- Confidential 50
- Cr motor 50
- Disassembly reassembly cr motor 50 50
- L800 l801 revision a 50
- Confidential 51
- Disassembly reassembly cr motor 51 51
- L800 l801 revision a 51
- Confidential 52
- Cr unit 52
- Disassembly reassembly cr unit 52 52
- L800 l801 revision a 52
- Confidential 53
- Disassembly reassembly cr unit 53 53
- L800 l801 revision a 53
- Asf unit 54
- Confidential 54
- Disassembly reassembly asf unit 54 54
- L800 l801 revision a 54
- Confidential 55
- Disassembly reassembly asf unit 55 55
- L800 l801 revision a 55
- Confidential 56
- Disassembly reassembly upper paper guide 56 56
- L800 l801 revision a 56
- Upper paper guide 56
- Apg sensor assy 57
- Confidential 57
- Disassembly reassembly apg sensor assy 57 57
- Front paper guide assy 57
- L800 l801 revision a 57
- Confidential 58
- Disassembly reassembly front paper guide assy 58 58
- L800 l801 revision a 58
- Confidential 59
- Disassembly reassembly front paper guide assy 59 59
- L800 l801 revision a 59
- Cdr tray sensor 60
- Confidential 60
- Disassembly reassembly cdr tray sensor 60 60
- L800 l801 revision a 60
- Attach the refilling ink label and valve position label according to the standards shown in the figure above 61
- Confidential 61
- Disassembling the ciss section 61
- Disassembly reassembly refilling ink label valve position label 61 61
- L800 l801 revision a 61
- Refilling ink label valve position label 61
- Top cover 61
- When attaching the top cover label align it with the markings on the top cover as shown in the figure above 61
- Confidential 62
- Disassembly reassembly tube valve holder front rear 62 62
- Follow the procedure below when installing the tube valve holder rear 1 insert the ribs x2 of the tube valve holder rear under the hooks x2 of the valve case 2 align the dowels x4 of the tube valve holder rear with the positioning holes x2 of the ink supply tank and the positioning holes x2 of the tube valve holder front 3 make sure no ink supply tank tubes are caught then secure it with the screws x3 in the order shown in the above figure 62
- Follow the procedure below when removing the valve lever 1 remove the ink supply tank assy from the printer 2 insert a flathead precision screwdriver or the like into the gap between the right cover and the tube valve holder rear to release the hook of the valve lever and then remove the valve lever 62
- L800 l801 revision a 62
- Tube valve holder front rear 62
- Tube valve holder front rear 1 valve lever 62
- Valve lever 62
- When routing the ink supply tank tubes align them with their red lines facing the tube valve holder front without any twist 62
- Be careful about how to place the ink supply tank assy in order to prevent printing failure from occurring see how to place the ink tank assy when disassembling reassembling p 0 63
- Bottom cover left cover right cover cover joint 63
- Confidential 63
- Disassembly reassembly bottom cover left cover right cover cover joint 63 63
- L800 l801 revision a 63
- Remove the exterior parts of the ink supply tank assy in the following order 1 remove the screws x8 of the bottom cover and remove the bottom cover 2 remove the left cover and right cover 3 remove the cover joint 63
- The figures above indicate the hooks and ribs that secure the parts 63
- Tighten the screws in the order indicated in the figure above 63
- Be careful about how to place the ink supply tank assy in order to prevent printing failure from occurring see how to place the ink tank assy when disassembling reassembling p 0 64
- Be careful not to damage or peel off the film of the ink supply tank 64
- C m lm lc bk y 64
- Confidential 64
- Disassembly reassembly ink supply tank assy 64 64
- Ink supply tank assy 64
- Ink supply tank assy 1 ink supply tank tube assy 64
- Ink supply tank tube assy 64
- L800 l801 revision a 64
- Route the ink supply tank tubes with the red lines facing upward as viewed when the ink supply tank assy is installed on the printer and connect them to the ink supply tank assy without any twist 64
- When connecting the ink supply tank tubes to the ink supply tank confirm the color indicated on the film of the ink supply tank and take care not to connect them with wrong joints 64
- When connecting the ink supply tank tubes to the ink supply tank insert the tubes to the full and make sure the gaps between the end of tubes and the tank are 0 mm long or less 64
- Be careful not to damage the cover case with the edges of the front frame 65
- Confidential 65
- Cover case 65
- Disassembly reassembly joint 65 65
- Follow the procedure below when removing the cover case 1 remove the screw x1 2 lift the cover case slightly to release the dowels x2 on the bottom of the cover case 3 rotate the cover case in the direction of the arrow 1 to avoid the section a and b of the cover case from bumping against the front frame 4 remove the cover case in the direction of the arrow 2 while avoiding the section c of the cover case from bumping against the front frame 65
- Joint 1 cover case 65
- L800 l801 revision a 65
- Make sure the gaps between the end of ink supply tank tubes or ink supply tubes and the joint are 0 mm long or less 65
- Make sure the red lines of the ink supply tank tube and ink supply tube facing upward 65
- When attaching the joint align the cutout of the joint with the rib of the cover case 65
- Confidential 66
- Disassembly reassembly pf scale cover pf scale sheet 66 66
- Follow the procedure below when attaching the pf scale cover pf scale sheet 1 wipe off the area on the main frame shown above using a cloth moistened with alcohol 2 align the pf scale cover with the rib of the front paper guide assy and attach the pf scale cover 3 align the screw holes of the pf scale cover and front paper guide assy and secure the pf scale cover with the screw x1 4 after the alcohol dried out completely insert the section a of the pf scale sheet into the groove of the front paper guide assy and then attach it with double sided tape 66
- L800 l801 revision a 66
- Pf scale cover pf scale sheet 66
- Pf scale cover pf scale sheet 1 1 tube guide sheet tube guide sheet sub 66
- Refer the figure above and follow the procedure below when attaching the tube guide sheet sub to the tube guide sheet 1 insert the section a of the tube guide sheet sub into the hole 1 of the tube guide sheet from the bottom 2 insert the section a of the tube guide sheet sub into the hole 2 of the tube guide sheet from the top 66
- Tube guide sheet tube guide sheet sub 66
- When attaching the tube guide sheet to the tube guide while keeping the tube guide sheet sub attached on the tube guide sheet align the holes of the tube guide sheet with the protrusions of the tube guide 66
- Confidential 67
- Connect the ink supply tube to the adapter and install the adapter to the cr unit p 8 67
- Disassembly reassembly ink supply tube assy 67 67
- Follow the procedure below when installing the ink supply tube assy 1 place the ink supply tube onto the tube guide sheet with its tube porous pad side down 2 connect the ink supply tubes x6 to the joint 3 insert the section a of the tube guide sheet sub from the top into the hole of the tube guide sheet sub to secure it 4 attach the tube holders x3 and secure them with the screws in the order shown in the figure above 67
- Hold the ink supply tube by the adapter side and flip it over as shown in the figure then put a marking on the bottom side of the ink supply tube 70 mm from the tube clamp nearest to the adapter 67
- Ink supply tube assy 67
- L800 l801 revision a 67
- Make sure the tube clamps with porous pad tube attached x3 are attached on the positions on the ink supply tube shown above 67
- Route the ink supply tubes through the grooves of the cr unit and align the markings on the ink supply tubes with the edge of the grooves as shown in the figure above 67
- Adapter 68
- Adapter cover 68
- Adapter cover 1 4 adapter 68
- After installing the adapter cover to the cr unit move the cr unit from side to side while holding the timing belt to make sure that the ink supply tube assy does not apply extra load of the cr unit movement 68
- Be careful not to damage or peel off the film of the adapter 68
- Confidential 68
- Disassembly reassembly adapter cover 68 68
- Follow the procedure below when installing the adapter cover to the cr unit 1 attach the tube guide sheet to the adapter cover 2 insert the dowels x2 of the adapter cover into the holes x2 of the cr unit and engage the hook of the adapter cover to the cr unit 3 make sure no ink supply tubes are caught then secure the adapter cover with the screw x1 68
- L800 l801 revision a 68
- Use a precision screwdriver when releasing the hooks of the adapter 68
- When connecting the ink supply tubes to the adapter make sure the red lines on the ink supply tubes are facing upward as shown in the figure above 68
- Adjustment 69
- C h a p t e r 69
- Adjustment adjustment items and overview 70 70
- Adjustment items and overview 70
- Confidential 70
- For information on how to carry out the adjustments and media required for the adjustments see the instructions displayed by the adjustment program 70
- L800 l801 revision a 70
- Servicing adjustment item list 70
- Some pictures in this manual are for epson stylus photo r280 r285 r290 therefore the shapes of the parts are different from those of l800 l801 but the differences does not affect the adjustment procedures 70
- Table 2 1 adjustment items 70
- The adjustment items of this product are as follows 70
- This chapter describes adjustments necessary after the disassembly reassembly of the printer 70
- Adjustment adjustment items and overview 71 71
- Confidential 71
- L800 l801 revision a 71
- Table 2 1 adjustment items 71
- Adjustment adjustment items and overview 72 72
- Confidential 72
- L800 l801 revision a 72
- Table 2 2 maintenance items 72
- Table 2 3 additional functions 72
- Adjustment adjustment items and overview 73 73
- Confidential 73
- L800 l801 revision a 73
- Table 2 3 additional functions 73
- Adjustment adjustment items and overview 74 74
- Confidential 74
- L800 l801 revision a 74
- Required adjustments 74
- Table 2 4 adjustment items 74
- The table below lists the required adjustments depending upon the parts being repaired or replaced find the part s you removed or replaced and check which adjustment s must be carried out 74
- Adjustment adjustment items and overview 75 75
- Confidential 75
- L800 l801 revision a 75
- Table 2 4 adjustment items 75
- Adjustment adjustment items and overview 76 76
- Confidential 76
- L800 l801 revision a 76
- Table 2 4 adjustment items 76
- Head angular adjustment 77
- Top margin adjustment 77
- Using the adjustment program 77
- Bi d adjustment 78
- Ok ng ng 78
- A pw adjustment pattern line left 79
- Adjustment using the adjustment program 79 79
- Area where a and b overlap 79
- B first dot position adjustment pattern line 79
- Confidential 79
- Enter the value for the line that is exactly 5mm away from the paper edge for each of the left right top and bottom 79
- Enter the value for the point where the pw adjustment pattern line and the first dot position adjustment pattern line overlap on the left of the paper 79
- Example in the left figure enter 0 top 0 right 5 bottom and 3 left 79
- Example in the left figure enter 2 since the lines overlap at 2 position 79
- Figure 2 5 pw first dot position adjustment pattern 79
- First dot position adjustment 79
- How to judge 79
- L800 l801 revision a 79
- Patterns are printed as shown below 79
- Pw adjustment 79
- Pw adjustment first dot position adjustment 79
- 2 1 0 1 2 3 3 80
- Ok ng ng 80
- Pf adjustment 80
- Adjustment using the adjustment program 81 81
- Confidential 81
- Described below is the platen gap pg adjustment 81
- L800 l801 revision a 81
- Pg adjustment 81
- Adjustment using the adjustment program 82 82
- Confidential 82
- L800 l801 revision a 82
- Adjustment banding reduction system brs adjustment paper feed amount profile pfp correction 83 83
- Banding reduction system brs adjustment 83
- Banding reduction system brs adjustment paper feed amount profile pfp correction 83
- Confidential 83
- L800 l801 revision a 83
- Overview 83
- Paper feed amount profile pfp correction 83
- The following are the scanners that can be used for scanning the pattern in brs pfp adjustment when starting up the adjustment program select the scanner to use 83
- This section explains how to carry out brs pfp adjustments 83
- Adjustment banding reduction system brs adjustment paper feed amount profile pfp correction 84 84
- Carry out the adjustment following the adjustment flow below 84
- Confidential 84
- L800 l801 revision a 84
- Adjustment banding reduction system brs adjustment paper feed amount profile pfp correction 85 85
- Adjustment procedure 85
- Brs banding reduction system adjustment 85
- Confidential 85
- L800 l801 revision a 85
- Adjustment banding reduction system brs adjustment paper feed amount profile pfp correction 86 86
- Confidential 86
- L800 l801 revision a 86
- Pfp adjustment 86
- Adjustment banding reduction system brs adjustment paper feed amount profile pfp correction 87 87
- Confidential 87
- L800 l801 revision a 87
- C h a p t e r 88
- Maintenance 88
- Cleaning 89
- Maintenance request error 89
- Overview 89
- Printhead cleaning 89
- Service maintenance 89
- As the need arises during disassembly reassembly of the printer 90
- Confidential 90
- Figure 3 1 lubrication of driven pulley 1 90
- Figure 3 2 lubrication of driven pulley 2 90
- Figure 3 3 lubrication of driven pulley 3 90
- L800 l801 revision a 90
- Lubrication 90
- Lubrication of driven pulley 90
- Maintenance overview 90 90
- Never use oil or grease other than those specified in this manual use of different types of oil or grease may damage the component and adversely affect the printer operation observe the specified amount never apply excess 90
- Refer to the following figures for the lubrication points 90
- Table 3 1 specified lubricant 90
- The type and amount of the grease used to lubricate the printer parts are determined based on the results of the internal evaluations be sure to apply the specified type and amount of the grease to the specified parts during servicing mentioned below 90
- When parts that need lubrication is been replaced 90
- Confidential 91
- Ej frame assy bushing 91
- Figure 3 4 lubrication of front paper guide assy 1 91
- Figure 3 5 lubrication of front paper guide assy 2 91
- Figure 3 6 lubrication of ej frame assy 91
- Figure 3 7 lubrication of the front frame 1 91
- Front frame contact point left 91
- Front paper guide assy left 91
- Front paper guide assy right 91
- L800 l801 revision a 91
- Lubrication of ej frame assy 91
- Lubrication of front paper guide assy 91
- Maintenance overview 91 91
- Confidential 92
- Cr guide shaft retaining spring 92
- Figure 3 10 lubrication of the cr guide shaft pg cam 92
- Figure 3 11 lubrication for the cr guide shaft retaining spring 92
- Figure 3 8 lubrication of the front frame 2 92
- Figure 3 9 lubrication of the main frame 1 92
- Front frame contact point right 92
- L800 l801 revision a 92
- Lubrication of cr unit 92
- Main frame upper rear 92
- Maintenance overview 92 92
- Pg cam on both ends of cr guide shaft 92
- Confidential 93
- Contact point between cr unit and cr guide shaft 1 93
- Contact point between cr unit and cr guide shaft 2 93
- Contact point between main frame and i s 93
- Figure 3 12 lubrication of the cr guide shaft 1 93
- Figure 3 13 lubrication of the cr guide shaft 2 93
- Figure 3 14 lubrication of the i s 93
- Figure 3 15 lubrication of the apg unit 1 93
- L800 l801 revision a 93
- Lubrication of apg unit 93
- Lubrication of ink system 93
- Maintenance overview 93 93
- Shafts on apg unit 93
- Confidential 94
- Figure 3 16 lubrication of the apg unit 2 94
- Figure 3 17 lubrication of the asf unit 94
- Figure 3 18 lubrication of the ld roller shaft 1 94
- Figure 3 19 lubrication of the ld roller shaft 2 94
- Hole for ld roller on asf unit 94
- L800 l801 revision a 94
- Ld roller shaft curved surface 94
- Ld roller shaft flat surface 94
- Lubrication of asf unit 94
- Maintenance overview 94 94
- Rim of the apg unit spur gear 28 94
- Confidential 95
- Figure 3 20 lubrication of the ld roller shaft 3 95
- L800 l801 revision a 95
- Ld roller shaft curved surface ribs beside the ld roller 95
- Maintenance overview 95 95
- Appendix 96
- C h a p t e r 96
- Appendix 97 97
- Completing ink charge 97
- Condition 97
- Confidential 97
- L800 l801 revision a 97
- No cdr tray and no paper on the paper path 97
- Power on sequence 97
- Table 4 1 operation of the power on sequence 97
- The carriage is locked by the cr lock 97
- The printhead is capped with the cap of the ink system 97
- The stacker is not set on the cdr printing position 97
- This section describes the power on sequences 97
- Appendix 98 98
- Confidential 98
- L800 l801 revision a 98
- Table 4 1 operation of the power on sequence 98
- 2 the carriage slowly moves to the 0 digit side 99
- 2 the pf motor rotates counterclockwise and sets the cr lock 99
- 3 the carriage slowly returns to its home position 99
- Appendix 99 99
- Confidential 99
- Cr lock setting 14 1 the carriage slowly moves to the cr lock set position 99
- F by the thermistor on the printhead 8 the empty sanction operation may occur depending on the situation 9 if paper remains in the printer the pf roller rotates by steps enough to eject the paper forcibly 99
- L800 l801 revision a 99
- Note 1 the rotation direction of the pf motor is as follows clockwise paper is fed normally counterclockwise paper is fed backward 2 the condition of the cr lock is as follows red cr lock is set white cr lock is released 3 indicates the pg position any position means that the pg position is not recognized because apg is not reset yet 4 checks if the carriage is not deadlock such as the cr lock is caught in the gap of the carriage 5 eject the paper if any 6 when paper exists the existing measurement value saved in eeprom is read out therefore the pf motor does not rotate 7 executes when the detected temperature is under 5 99
- Operatio 99
- Parts unit 99
- Replacement adjustment total 99
- Standard operation time for servicing the product 99
- Table 4 1 operation of the power on sequence 99
- Table 4 2 standard operation time 99
- The following are the standard operation time for servicing the product those are based on the mttr result measured using a prototype 99
- The underlined parts units are supplied as after service parts 99
- Time second 99
- Appendix 100 100
- Confidential 100
- L800 l801 revision a 100
- Parts unit 100
- Replacement adjustment total 100
- Table 4 2 standard operation time 100
- Time second 100
- Appendix 101 101
- Confidential 101
- L800 l801 revision a 101
- Parts unit 101
- Replacement adjustment total 101
- Table 4 2 standard operation time 101
- Time second 101
- Troubleshooting 102
- Troubleshooting workflow 102
- Appendix troubleshooting workflow 103 103
- Confidential 103
- L800 l801 revision a 103
- Major problem with error message 103
- Major problem without error message 103
- This flowchart is compiled based on the following contents our experience regarding the quality problem esk s repair data on fy08 fy09 models printer mechanism specification for l800 l801 103
- Appendix fatal error code 104 104
- Confidential 104
- Fatal error code 104
- L800 l801 revision a 104
- Table 4 3 fatal error list 104
- This section describes the fatal error code and the possible cause for this product 104
- Appendix fatal error code 105 105
- Confidential 105
- L800 l801 revision a 105
- Table 4 3 fatal error list 105
Похожие устройства
- Vitek VT 1466 Руководство пользователя
- Magio MG-188 Инструкция по эксплуатации
- Magio MG-303 Инструкция по эксплуатации
- Magio MG-297 Инструкция по эксплуатации
- Magio MG-312 Инструкция по эксплуатации
- Magio MG-316 Инструкция по эксплуатации
- Magio MG-301 Инструкция по эксплуатации
- Magio MG-300 Инструкция по эксплуатации
- Magio MG-302 Инструкция по эксплуатации
- Magio MG- 311 Инструкция по эксплуатации
- Magio MG-307 Инструкция по эксплуатации
- Magio MG-308 Инструкция по эксплуатации
- Magio MG-310 Инструкция по эксплуатации
- Magio MG-304 Инструкция по эксплуатации
- Magio MG-309 Инструкция по эксплуатации
- Magio MG-299 Инструкция по эксплуатации
- Magio MG-298 Инструкция по эксплуатации
- Magio MG-157 Инструкция по эксплуатации
- Magio MG-162 Инструкция по эксплуатации
- Magio MG-161 Инструкция по эксплуатации
Скачать
Случайные обсуждения
Ответы 1
нажала кнопку печати но забыла вставить листок, он замолчал и теперь не печатает совсем( в чем дело? перезагружала и его и мак, но он все молчит и даже никаких ошибок не выдает.
10 лет назад