Home
Главная
Bosch
Аккумуляторные Универсальные Ножницы
GUS 10.8V-LI 0.601.9B2.900
Инструкция по эксплуатации Страница: 13

Bosch GUS 10.8V-LI 0.601.9B2.900 [13/146] Maintenance and service

English | 13

Bosch Power Tools 1 609 929 Y38 | (17.5.11)

Operation

f Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

Starting Operation

Inserting the Battery

f Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

ard.

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

– Insert the charged battery 6 into the handle until it can be

felt to engage and faces flush against the handle.

Switching On and Off

–To start the machine, push the On/Off switch 4 forward so

that the “I” is indicated on the switch.

–To switch off the machine, push the On/Off switch 4 to-

ward the rear so that the “0” is indicated on the switch.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Note: If the machine should automatically switch off because

of a discharged or overheated battery, make sure to set the

machine’s On/Off switch 4 to off. Charge the battery and al-

low it to cool down before restarting the machine. Otherwise

the battery can become damaged.

Working Advice

f Do not strain the machine so heavily that it comes to a

standstill.

f Never touch the blade during operation 10.

The cutting performance of the machine depends on the ma-

terials to be cut and on the charging condition of the battery.

Depending on the charge condition of the battery, excessive

feed considerably reduces the performance capability.

Always keep the blade free and clean of material remainders.

The guide edge 12 may not become wedged during cutting

and must be aligned parallel to the cutting surface.

Improper use will make the blade dull.

Thin materials, such as fabrics, can be pulled into the machine

during cutting and become wedged. Therefore, do not apply

too much pressure with such materials in order to achieve

good cutting results. During cutting, apply sufficient tension

while holding fabrics and cut slowly.

Do not remove drawn in material during operation and switch

the power tool off first with the On/Off switch 4.

Optimum cutting results are best determined through practi-

cal testing.

Adjusting the Blade Guard

f Never operate the machine without the blade guard 3.

For optimal protection of your fingers against injuries, the

blade guard must be adjusted to the material thickness being

cut before each work step.

– Loosen the knurled screw 1.

– Adjust blade guard 3 in such a manner that it faces loosely

against the material to be cut.

– Tighten knurled screw 1 again.

Note: Position the blade guard 3 completely down each time

after using the machine and before carrying out an inspection

or maintenance.

“Cut Control” Cutting-line Mark

The red line on the blade guard (“Cut Control” cutting-line

mark 2) indicates the cutting line of the blade 10.

This allows for precise guiding of the machine alongside the

cutting line marked on the material.

Temperature Dependent Overload Protection

When using as intended for, the machine cannot be overload-

ed. In case of excessive loading or when exceeding the allow-

able battery temperature range of 0–70 °C, the speed is re-

duced or the machine switches off. In case of reduced speed,

the machine will not run at full speed until after reaching the

allowable battery temperature again. In case of automatic

shut-off, switch the machine off, allow the battery to cool

down and then switch the machine on again.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between

0 °C and 50 °C. As an example, do not leave the battery in the

car in summer.

A significantly reduced working period after charging indi-

cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

f For safe and proper working, always keep the machine

and ventilation slots clean.

While cutting, material residue can accumulate under the

blade guard.

– Clean the blade guard 3 regularly using a brush or lightly

moistened cloth.

If the machine should fail despite the care taken in manufac-

turing and testing procedures, repair should be carried out by

an after-sales service centre for Bosch power tools.

OBJ_BUCH-1417-001.book Page 13 Tuesday, May 17, 2011 11:37 AM

Содержание

Похожие устройства

OBJ BUCH 1417 001 book Page 13 Tuesday May 17 2011 11 37 AM English 113 Adjusting the BladeGuard Operation Never operate the machine without the blade guard 3 Beforeany work on the machine itself e g mainte For optimal protection of your fingers against injuries the nance tool change etc as well as during transport bl ade guard must be adj usted to the materi al thi ckness bei ng cut before each work step and storage remove the battery from the power tool There is danger of injury when unintentionally actuating the On Off switch Loosen the knurled screw 1 Adjust blade guard 3 in such a manner that it faces loosely Starting Operation againstthe material to be cut Tighten knurled screw 1 again Inserting the Battery Note Position the blade guard3 completely down each time after using the machine and before carryingout an inspection Use only original Bosch lithium ion batteries with the voltage listed on the nameplate of your power tool Us ing other batteries can lead to injuries and pose a fire haz or maintenance ard Note Useofbatteriesnotsuitableforthemachine Cut Control Cutting line Mark canlead to malfunctions of or cause damage to the power tool Insert the charged battery 6 into the handle until it can be felt to engage and faces flush against the handle The red line on the blade guard Cut Control cutting line mark 2 indicates the cutting line of the blade 10 This allows for precise guiding of the machine alongside the cutting line marked on the material Switching On and Off Temperature Dependent Overload Protection To start the machine push the On Off switch 4 forward so When using as intended for the machine cannot be overload that the I is indicated on the swi tch To switch off the machine push the On Off switch 4 to ward the rear so that the 0 is indicated on the switch The lithium ion battery is protected against deep discharging by the ElectronicCell Protection ECP When the battery is empty the machine is switched off by means of a protective circuit The inserted tool no longer rotates ed In case of excessive loading or when exceeding the allow able battery temperature range of 0 70 C thespeed is re duced or the machine switches off In case of reduced speed the machine will not run at full speed until after reaching the allowable battery temperature again In case of automatic shut off switch the machine off allow the battery to cool down and then switch the machine on again Note If the machine should automatically switch off because of a discharged or overheated battery make sure toset the Recommendations for Optimal Handling of the Battery machine s On Off switch 4 to off Charge the battery and al Store the battery only within a temperature range between low it to cool down before restarting the machine Otherwise 0 C and 50 C As an example do not leave the battery in the the battery can become damaged car in summer Working Advice A significantly reduced working period after charging indi cates that the battery is used and must be replaced Do not strain the machine so heavily that it comesto a standstill Never touch the blade during operation 10 The cutting performance of the machine depends on the ma terials to be cut and on the charging condition of the battery Protect the battery against moisture and water Observe the notes for disposal Maintenance and Service Maintenance and Cleaning Depending on the charge condition of the battery excessive feed considerably reduces the performance capability Always keep the blade free and clean of material remainders The guide edge 12 may not become wedged during cutting and must be aligned parallel to the cutting surface Improper use will make the blade dull Before any work on the machine itself e g maintena nee tool cha nge etc a s well a s during transport and storage remove the battery from the power tool There is danger of injury when unintentionally actuating the On Off switch Thin materials such as fabrics can be pulled into themachi ne For sa fe a nd proper working a I ways keep the ma chine and ventilation slots clean during cutting and become wedged Therefore do not apply While cutting material residue can accumulate under the too much pressure with such materials in order to achieve blade guard good cutting results During cutting apply sufficient tension while holding fabrics and cut slowly Clean the blade guard 3 regularly using a brush or lightly Do not remove drawn in material during operation and switch moistened cloth the power tool off firstwith the On Off switch 4 If the machine should fail despite the care taken in manufac turing and testing procedures repairshould be carried outby Optimum cutting results are best determined through practi an after sales service centre for Bosch power tools cal testing Bosch Power Tools 1609 929 Y38I117 5 11

Скачать