Metabo TKHS 315 M [25/64] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Metabo TKHS 315 M [25/64] English

Metabo TKHS 315 M [25/64] English
25
ENGLISH
6. Align hose carrier, tighten hexagon
head screws and flange nuts. Hook
the suction hose into the hose car-
rier (87).
7. Connect the saw's dust extraction
port at the chipcase to a suitable
dust collector (see "Dust collector" in
chapter "Operation").
Mitre fence assembly
1. Attaching the front mounting bracket
(92) to the left-hand front side of the
saw:
− Remove the hexagon head
screws (91) from the left-hand
front and rear side of the table
panel.
− Put two each hexagon head
screws (91) fitted, from the out-
side through the mounting
bracket (92) and the table panel;
− from the inside screw on flange
nuts (90) – do not yet tighten
fully.
2. Mounting the guide bar (88): Insert
the guide bar into the mounting
bracket (92) so that the nose fits into
the slot in the guide bar. A slight turn
of the guide bar keeps it from sliding
off.
3. Slide the lower fence carrierl (89),
with the angle facing the front of the
saw on the guide bar and swing it
down.
4. Put the rear mounting bracket (93)
on the guide bar and secure by turn-
ing it sligthly.
5. Attach the rear mounting bracket,
with the bracket (95) for table exten-
sion installation to the saw.
6. Align guide bar exactly parallel with
the saw blade.
7. Tighten all screws holding the
mounting brackets.
8. Fit plugs (94) to both ends of the
guide bar.
9. Swing the lower fence carrier up.
10. Install the upper fence carrier (99)
with washer (98) and star-knob
screw (97).
11. Put the short fence extrusion (100)
on and secure with knurled nuts
(101):
− the plastic nose of the fence
extrusion must point towards the
saw blade;
− the washers (102) must be fitted
between between upper fence
carrier and knurled nuts.
12. By means of the set screw (96) the
fence extrusion can be set exactly
square to the saw blade. The set
screw (96) is accessible when the
mitre fence is swung down.
3
Note:
When the mitre fence is not
required swing it down, out of the way.
Adjusting the rip fence
1. Slide rip fence (106) on the guide
rail adn lock with the lock lever
(105).
2. Install the fence extrusion (103) as
illustrated below and secure it with
the two knurled thumb screws.
3. Slightly loosen both set screws
(104) of the rip fence and align the
fence extrusion parallel with the saw
blade. Retighten both set screws
afterwards.
4. Set rip fence against the right-hand
side of the saw blade, across its
entire diameter. Crank saw blade
up, if necessary.
5. Adjust scale so that its zero position
coincides exactly with the scale
reading edge (107) of the rip fence.
6. Tighten the scale fastening screw
and verify the setting by making a
trial cut.
Item Description Qty.
88
Guide bar
1
89
Fence carrier, lower
1
90
Flange nut M8
( ) = already installed
2
(2)
91
Hexagon head screw
M8 x 20
( ) = already installed
2
(2)
92
93
Mounting bracket
2
94
Plug
2
95
Bracket for table
extension
1
97
Star-knob screw M8
1
98
Washer 8.4
1
99
Fence carrier, upper
1
100
Fence extrusion,
short
1
85
86
87
88 89 90
91
92
93
94
95
97
98
99
96
100
102 101
103
104
105
106
107

Содержание

Похожие устройства

Скачать