Bosch GCL 25 PROFESSIONAL [15/189] Maintenance and service
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bosch GCL 25 PROFESSIONAL [15/189] Maintenance and service

Bosch GCL 25 PROFESSIONAL [15/189] Maintenance and service
English | 15
Bosch Power Tools 1 618 C00 50R | (24.1.12)
– Rotate the measuring tool by 180° without changing the
height. Allow it to level in and mark the centre point of the
laser beam on wall A (point III). Take care that point III is
as vertical as possible above or below point I.
– The difference d of both marked points I and III on wall A
results in the actual height deviation of the measuring tool
alongside the Longitudinal axis.
On the measuring distance of 2 x 20 m = 40 m, the maximum
allowable deviation is: 40 m x ± 0.3 mm/m = ±12 mm.
Thus, the difference d between points I and III may not ex-
ceed 12 mm (max.).
Working Advice
f For marking, always use only the centre of the laser
point or the laser line. The size of the laser point as well as
the width of the laser line change with distance.
Working with the Tripod (Accessory)
A tripod offers a stable, height-adjustable measuring support.
Position the measuring tool with the 1/4" tripod mount 7 onto
the thread of the tripod 16 or a commercially available cam-
era tripod. For fastening to a commercially available construc-
tion tripod, use the 5/8" tripod mount 6. Tighten the measur-
ing tool with the tripod mounting stud.
Adjust the tripod roughly before switching on the measuring
tool.
Fastening with the Universal Holder (Accessory)
With the universal holder 15, you can fasten the measuring
tool, e.g., to vertical surfaces, pipes or magnetizable materials.
The universal holder is also suitable for use as a ground tripod
and makes the height adjustment of the measuring tool easier.
Adjust the universal holder roughly before 15 switching on
the measuring tool.
Working with the Measuring Plate (Accessory)
(see figures A–B)
With the measuring plate 14, it is possible to project the laser
mark onto the floor or the laser height onto a wall.
With the zero field and the scale, the offset or drop to the
required height can be measured and projected at another
location. This eliminates the necessity of precisely adjusting
the measuring tool to the height to be projected.
The measuring plate 14 has a reflective coating that enhances
the visibility of the laser beam at greater distances or in
intense sunlight. The brightness intensification can be seen
only when viewing, parallel to the laser beam, onto the meas-
uring plate.
Working with the Laser Target Plate
The laser target plate 13 increases the visibility of the laser
beam under unfavourable conditions and at large distances.
The reflective part of the laser target plate 13 improves the
visibility of the laser line. Thanks to the transparent part, the
laser line is also visible from the back side of the laser target
plate.
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out the ambient light. This
makes the red light of the laser appear brighter for the eyes.
f Do not use the laser viewing glasses as safety goggles.
The laser viewing glasses are used for improved visualisa-
tion of the laser beam, but they do not protect against laser
radiation.
f Do not use the laser viewing glasses as sun glasses or in
traffic. The laser viewing glasses do not afford complete
UV protection and reduce colour perception.
Work Examples (see figures C – F)
Applicational examples for the measuring tool can be found
on the graphics pages.
Always position the measuring tool close to the surface or
edge subject to checking, and allow it to level in prior to each
measurement.
Always measure the distances between laser beam or laser
line and a surface or edge at two points as far as possible away
from each other (e.g. with the measurment plate 14).
Maintenance and Service
Maintenance and Cleaning
Store and transport the measuring tool only in the supplied
case.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool in water or other fluids.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
Regularly clean the surfaces at the exit opening of the laser in
particular, and pay attention to any fluff of fibres.
If the measuring tool should fail despite the care taken in man-
ufacturing and testing procedures, repair should be carried
out by an authorised after-sales service centre for Bosch
power tools. Do not open the measuring tool yourself.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the measuring tool.
For repairs, only send in the measuring tool in the case.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
d
180°
A
B
OBJ_BUCH-1546-001.book Page 15 Tuesday, January 24, 2012 4:18 PM

Содержание

Похожие устройства

4 OBJBUCH l 546 001 book Page 15 Tuesday January24 2012 4 18PM English 115 Working with the Laser Target Plate The laser target plate 13 increases the visibility of the laser beam under unfavourable conditions and at large distances The reflective part of the laser target plate 13 improves the visibility of the laser line Thanks to the transparent part the laser line is also visible from the back side of the laser target plate Laser Viewing Glasses Accessory The laser viewingglasses filter out the ambient light This makes the red light of the laser appear brighter for the eyes Rotate the measuring tool by 180 without changing the Do not use the laser viewing glassesas safety goggles height Allow it to level in and mark the centre point of the The laser viewing glasses are used for improved visualisa laser beam on wall A point III Take care that point III is tion of the laser beam but they donot protect against laser radiation as vertical as possible above or below point I The difference d of both marked points I and III on wall A results in the actual height deviation of the measuring tool Do not use the la ser viewing gla sses a s sun gla sses or in traffic The laser viewing glasses do not afford complete UV protection and reduce colour perception alongside the Longitudinal axis On the measuring distance of 2 x 20 m 40 m the maximum Work Exa mples see figures C F allowable deviation is 40 m x 0 3 mm m 12 mm Applicational examples for the measuring tool can be found Thus the difference d between points I and III may not ex ceed 12 mm max on the graphics pages Always position the measuring tool close to the surface or edge subject tochecking and allow it to level in prior toeach Working Advice measurement For marking always use only the centre of the laser Always measure the distances between laser beam or laser point orthelaser line Thesizeofthelaser point as well as lineandasurfaceoredgeattwopointsasfaraspossibleaway the width of the laser line change with distance from each other e g with the measurment plate 14 Working with the Tripod Accessory A tri pod offers astable height adjustable measuringsupport Posi ti on the measuri ng tool wi th the 1 4 tri pod mount 7 onto Maintenance and Service the thread of the tripod 16 or a commerdally available cam Maintenanceand Cleaning era tri pod For fastening to a commercial ly avail able construc Store and transport the measuring tool only in the supplied tion tripod use the 5 8 tripod mount 6 Tighten the measur case ing tool with the tripod mounting stud Adjust the tripod roughly Keep the measuring tool clean at all times before switching on themeasuring tool Donot immerse the measuring tool in water or other fluids Wi pe off debris using a moist and soft cloth Do not use any Fastening with thellniversal Holder Accessory cleaning agents or solvents With the universal holder 15 you can fasten themeasuring Regularly clean thesurfaces at the exit opening of the laser in tool e g to vertical surfaces pipes or magnetizablematerials particular and pay attention to any fluff of fibres Theuniversal holder is also suitable for use as a ground tripod If the measuring tool should fail despitethecaretaken in man and makes the height adjustment of the measuring tool easier ufacturingand testing procedures repair should be carried Adjust the universal holder roughly before 15 switching on out by an authorised after sales service centre for Bosch themeasuring tool Working with power tools Do not open themeasuring tool yourself the Measuring Plate In all correspondence and spare parts orders please always Accessory incl ude the 10 digi t artid e number given on the type plate of see figures A B With themeasuring plate 14 it is possibleto project the laser the measuring tool mark onto the floor or the laser height onto a wall For repairs only send in the measuring tool in the case With the zero field and the scale the offset or drop to the After sales Service a nd Customer Assista nee required height can be measured and projected at another location This eliminates the necessity of predsely adjusting Our after sales service responds toyour questions concern ing maintenance and repair of your product as well as spare the measuring tool to the height to be projected parts Exploded views and information on spare parts can Themeasuring plate 14 has a reflective coating that enhances the visibility of the laser beam atgreater distances or in intensesunlight The brightness intensification can beseen only when viewing parallel to the laser beam onto the meas uri ng pl ate Bosch Power Tools also be found under www bosch pt com Our customer service representatives can answer your ques tions concerning possible applications and adjustment of products and accessories 1618C0050RK24 1 12

Скачать