Home
Главная
GRAPHITE
Шлифовальная Машина
59G187
Инструкция по эксплуатации Страница: 14

GRAPHITE 59G187 Инструкция по эксплуатации онлайн [14/120] 809851

e) Do not attach a saw chain woodcarving blade or toothed saw

blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specic for Grinding and Abrasive Cutting-O

Operations:

a) Use only wheel types that are recommended for your power

tool and the specic guard designed for the selected wheel.

Wheels for which the power tool was not designed cannot be

adequately guarded and are unsafe.

b) The grinding surface of centre depressed wheels must be

mounted below the plane of the guard lip. An improperly

mounted wheel that projects through the plane of the guard lip

cannot be adequately protected.

c) The guard must be securely attached to the power tool and

positioned for maximum safety, so the least amount of wheel

is exposed towards the operator. The guard helps to protect the

operator from broken wheel fragments, accidental contact with

wheel, and sparks that could ignite clothing.

d) Wheels must be used only for recommended applications. For

example: do not grind with the side of cut-o wheel. Abrasive

cut-o wheels are intended for peripheral grinding, side forces

applied to these wheels may cause them to shatter.

e) Always use undamaged wheel anges that are of correct

size and shape for your selected wheel. Proper wheel anges

support the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-o wheels may be dierent from

grinding wheel anges.

f) Do not use worn down wheels from larger power tools. Wheel

intended for larger power tool is not suitable for the higher speed

of a smaller tool and may burst.

Additional Safety Warnings Specic for Abrasive Cutting-O

Operations:

a) Do not “jam” the cut-o wheel or apply excessive pressure. Do

not attempt to make an excessive depth of cut. Overstressing

the wheel increases the loading and susceptibility to twisting or

binding of the wheel in the cut and the possibility of kickback or

wheel breakage.

b) Do not position your body in line with and behind the rotating

wheel. When the wheel, at the point of operation, is moving away

from your body, the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

reason, switch o the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never

attempt to remove the cut-o wheel from the cut while the

wheel is in motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the power tool is restarted

in the workpiece.

e) Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend to

sag under their own weight. Support must be placed under the

workpiece near the line of cut and near the edge of the workpiece

on both sides of the wheel.

f) Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Specic for Sanding Operations:

a) Do not use excessively oversized sanding disc paper. Follow

manufacturers recommendations, when selecting sanding

paper. Larger sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snagging, tearing of

the disk or kickback.

Safety Warnings Specic for Polishing Operations:

a) Do not allow any loose portion of the polishing bonnet or its

attachment strings to spin freely. Tuck away or trim any loose

attachment strings. Loose and spinning attachment strings can

entangle your ngers or snag on the workpiece.

Safety Warnings Specic for Wire Brushing Operations:

a) Be aware that wire bristles are thrown by the brush even

during ordinary operation. Do not overstress the wires by

applying excessive load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing, do

not allow any interference of the wire wheel or brush with the

guard. Wire wheel or brush may expand in diameter due to work

load and centrifugal forces.

Additional safety Warnings:

a) In tools adapted to attach grinding wheels with a threaded hole,

check whether the thread length of the grinding wheel is suitable

for the length of the spindle thread.

b) Secure the workpiece. Attaching the workpiece to the clamping

device or vise is safer than holding it in your hand.

c) Do not touch the cutting and grinding discs until they have

cooled down.

d) When using a quick-setting ange, make sure that the

internal ange mounted on the spindle is equipped with a

rubber O-ring and that the ring is undamaged. It should also

be ensured that the surfaces of the external ange and the

internal ange are clean.

e) Use the quick clamping ange only with abrasive and cutting

discs. Only use undamaged and properly functioning anges.

f) In the event of a temporary power outage in the network or after

removing the plug from the power socket with the switch in the

"on" position, before re-starting, unlock the switch and set it in the

o position.

CAUTION! This device is designed to operate indoors. The design

is assumed to be safe, protection measures and additional safety

systems are used, nevertheless there is always a small risk of

injuries at work.

Descriptions of used pictograms.

1 2 3 4

5 6 7 8

1. Warning, take special precautions.

2. Read the instruction manual, observe warnings and safety

conditions included in it!

GRAPHITE 59G187 Инструкция по эксплуатации онлайн [14/120] 809851

Содержание

Похожие устройства