![Planet WGS3-2820 [464/528] 4 ip ospf transmit delay](/img/pdf.png)
Planet WGS3-2820 [464/528] 4 ip ospf transmit delay
User’s Manual of WGS3-2820/WGS3-5220
464
This command sets the default OSPF retransmit Interval for the specified interface.
▫ Format no ip ospf retransmit-interval
▫ Mode Interface Config
12.7.34 ip ospf transmit-delay
This command sets the OSPF Transit Delay for the specified interface. The transmit delay is specified in seconds. In addition, it
sets the estimated number of seconds it takes to transmit a link state update packet over this interface. Valid values for
<seconds> range from 1 to 3600 (1 hour).
▫ Default 1
▫ Format ip ospf transmit-delay <1-3600>
▫ Mode Interface Config
no ip ospf transmit-delay
This command sets the default OSPF Transit Delay for the specified interface.
▫ Format no ip ospf transmit-delay
▫ Mode Interface Config
12.7.35 ip ospf mtu-ignore
This command disables OSPF maximum transmission unit (MTU) mismatch detection. OSPF Database Description packets
specify the size of the largest IP packet that can be sent without fragmentation on the interface. When a router receives a
Database Description packet, it examines the MTU advertised by the neighbor. By default, if the MTU is larger than the router
can accept, the Database Description packet is rejected and the OSPF adjacency is not established.
▫ Default enabled
▫ Format ip ospf mtu-ignore
▫ Mode Interface Config
no ip ospf mtu-ignore
This command enables the OSPF MTU mismatch detection.
▫ Format no ip ospf mtu-ignore
▫ Mode Interface Config
12.7.36 router-id (OSPF)
This command sets a 4-digit dotted-decimal number uniquely identifying the router ospf id. The <ipaddress> is a configured
value.
▫ Format router-id <ipaddress>
▫ Mode Router OSPF Config
Содержание
- 48 port 10 100mbps 4 port gigabit tp 2 sfp combo layer 3 managed ethernet switch 1
- User s manual 1
- Wgs3 2820 wgs3 5220 1
- Ce mark warning 2
- Disclaimer 2
- Fcc warning 2
- Revision 2
- Trademarks 2
- Weee warning 2
- Table of contents 3
- Introduction 19
- Packet contents 19
- How to use this manual 20
- Product feature 20
- Product specification 23
- Installation 25
- Product description 25
- Product overview 25
- Base t sfp mini gbic port 26
- Led color function 26
- Led indications 26
- Switch front panel 26
- Desktop installation 27
- Install the switch 27
- Switch rear panel 27
- Rack mounting 28
- Installing the sfp transceiver 29
- Configuration 31
- Management access overview 31
- Administration console 32
- Direct access 32
- Protocols 33
- Snmp based network management 33
- Virtual terminal protocols 33
- Web management 33
- Management architecture 34
- Snmp protocol 34
- Web configuration 35
- Main menu 37
- System description 38
- Arp cache 39
- Configure system 39
- Inventory information 40
- Configuration 41
- System description 41
- Switch configuration 42
- Network connectivity 43
- Telnet session 44
- Outbound telnet client configuration 45
- Remote session 45
- Serial port 46
- User accounts 47
- Authentication list configuration 48
- Login session 49
- Authentication list summary 50
- User login 50
- Configuration 52
- Forwarding database 52
- Search 52
- Buffered log 54
- Command logger configuration 54
- Console log configuration 55
- Event log 55
- Hosts configuration 56
- Persistent log configuration 57
- Persistent log 58
- Syslog configuration 59
- Summary 61
- Multiple port mirroring 62
- Periodic port mirroring 63
- Double vlan tunneling 64
- Double vlan tunneling summary 65
- Community configuration 66
- Supported mibs 67
- Trap receiver configuration 67
- Statistics 68
- Switch detail 68
- Switch summary 70
- Port detailed 71
- Port summary 74
- Cpu statistics 75
- Save all applied changes 76
- System utilities 76
- Reset configuration to default 77
- System reset 77
- Reset password to default 78
- Download file to switch 79
- Upload file from switch 80
- Trap flags 81
- Trap management 81
- Trap log 82
- Dhcp server 83
- Global configuration 83
- Pool configuration 84
- Pool options 87
- Bindings information 88
- Reset configuration 88
- Server statistics 89
- Conflicts information 90
- Global configuration 91
- Global status 92
- Server configuration 93
- Server status 95
- Switching 96
- Vlan configuration 99
- Vlan status 100
- Vlan port configuration 101
- Vlan port summary 102
- Vlan reset configuration 103
- Configuration 104
- Protocol based vlan 104
- Protocol based vlan summary 105
- Port security 106
- Port security administration 106
- Port security interface configuration 106
- Port security static 108
- Port security dynamic 109
- Port security violation status 109
- Port mac deny 110
- Port mac deny listing 110
- Cpu multicast configuration 111
- Garp port configuration 113
- Garp switch configuration 113
- Igmp snooping 115
- Igmp snooping configuration and status 117
- Igmp snooping interface configuration 118
- Vlan configuration 119
- Vlan status 119
- Multicast router statistics 120
- Multicast router configuraton 122
- Multicast router vlan statistics 122
- Multicast router vlan configuration 123
- Port channel 123
- Port channel configuration 124
- Switch configuration 124
- Port channel status 125
- Mfdb table 127
- Multicast forwarding database 127
- Gmrp table 128
- Multicast forwarding database statistics 129
- Spanning tree 130
- Lan 2 lan 3 134
- Portcast 19 134
- Portcast 19 portcast 19 134
- Portcast 4 134
- Spanning tree switch configuration status 136
- Spanning tree cst configuration status 137
- Spanning tree mst configuration status 138
- Spanning tree cst port configuration status 139
- Spanning tree mst port configuration status 141
- Spanning tree statistics 143
- Class of service 144
- P priority mapping 144
- Security 145
- Port access control 148
- Port access control configuration 148
- Port access summary 154
- Radius 156
- Radius configuration 156
- Radius server configuration 157
- Windows platform radius server configuration 158
- Radius server statistics 161
- Radius accounting server configuration 163
- Radius accounting server statistics 164
- Configure sample eap md5 authentication 165
- Radius clear statistics 165
- X client configuration 165
- Tacacs 168
- Tacacs configuration 168
- Server configuration 169
- Secure http 170
- Secure http configuration 170
- Secure shell 171
- Secure shell configuration 171
- Ip access control list 172
- Ip acl configuration 172
- Ip acl summary 173
- Ip acl rule configuration 174
- Mac access control list 176
- Mac acl configuration 176
- Mac acl summary 177
- Mac acl rule configuration 178
- Acl interface configuration 181
- Differentiated services 183
- Diffserv configuration 183
- Diffserv class configuration 184
- Diff policy configuration 186
- Diffserv class summary 186
- Diffserv policy summary 187
- Diffserv policy attribute summary 188
- Diffserv policy class definition 188
- Diffserv service configuration 189
- Diffserv service statistics 190
- Diffserv service summary 190
- Diffserv service detailed statistics 191
- Class of service 193
- Trust mode configuration 193
- Ip precedence mapping configuration 194
- Ip dscp mapping configuration 195
- Interface configuration 196
- Interface queue configuration 196
- Interface queue status 198
- Routing 199
- Ip configuration 202
- Ip statistics 203
- Ip interface configuration 205
- Ip interface secondary address configuration 207
- Vlan routing 208
- Vlan routing configuration 208
- Vlan routing summary 210
- Rip configuration 211
- The routing information protocol is used to specify how routers exchange routing table information see rip and rip 2 dynamic routing protocols on chapter advanced topics when rip is enabled on this routing switch it broadcasts rip messages to all devices in the network every 30 seconds and updates its own routing table when rip messages are received from other routers rip messages contain both the ip address and a metric for each destination network it knows about where the metric indicates the number of hops from this device to the destination network 211
- Rip interface summary 212
- Rip interface configuration 214
- Rip route redistribution configuration 216
- Rip route redistribution summary 218
- Ospf configuration 220
- Ospf interface configuration 222
- Ospf area configuration 227
- Ospf protocol broadcast messages i e link state advertisements are restricted by area to limit their impact on network performance before assigning an area id to a specific ospf interface you must first specify the area id in this table each entry in this table identifies a logical group of ospf routers that actively exchange link state advertisements lsas to ensure that they share an identical view of the network topology you can configure the area as a normal one which can send and receive external link state advertisements lsas a stubby area that cannot send or receive external lsas or a not so stubby area nssa that can import external route information into its area 227
- Ospf stub area summary 229
- After you configure an area identifier you can specify a subnetwork address range that covers all the individual networks in this area this technique limits the amount of traffic exchanged between area border routers abrs by allowing them to advertise a single summary range by summarizing routes the routing changes within an area do not have to be updated in the backbone abrs or in other areas 230
- Ospf area range configuration 230
- To optimize the route summary first configure all the ospf routers in an area so that they fall within a contiguous address range the route summary consists of an address and mask where the mask can be a variable length subnet mask vlsm using vlsms allows you to configure each subnetwork within a larger network with its own subnet mask this provides a longer subnet mask that covers fewer host ip addresses thereby reducing the size of the routing tables that have to be exchanged for more information on vslms see rfcs 1219 and 1878 230
- Ospf interface statistics 232
- Ospf neighbor table 234
- Ospf neighbor configuration 235
- Ospf link state database 237
- All ospf areas must connect to the backbone if an area does not have a direct physical connection to the backbone you can configure a virtual link that provides a logical path to the backbone to connect an isolated area to the backbone the logical path can cross a single nonbackbone area to reach the backbone to define the path you must specify one endpoint on the abr that connects the isolated area to the common nonbackbone area and the other endpoint on the abr that connects this common nonbackbone area and the backbone itself however note that you cannot configure a virtual link that runs through a stub or nssa area 239
- Ospf virtual link configuration 239
- To configure a virtual link specify the transit area through which the endpoint routers connect and the address of the router on this side of the link 239
- Virtual links can also be used to create a redundant link between any area and the backbone to help prevent partitioning or to connect two existing backbone areas into a common backbone 239
- Ospf route redistribution configuration 242
- Ospf virtual link summary 242
- Ospf route redistribution summary 245
- Router 246
- Router table 246
- Router best routes table 247
- Route entry configuration 248
- Route preferences configuration 249
- Before defining a static route remember that you must first configure at least one ip interface on this switch static routes take precedence over dynamically learned routes and remain in the table until you remove them or the corresponding ip interface from this switch 250
- Configured routes 250
- This switch can be configured to dynamically learn the routes to other ip networks subnets or hosts using unicast or multicast routing protocols if the route to a specific destination cannot be learned via these protocols or you wish to restrict the path used for transmitting traffic to a destination then it can be statically configured using the static route table 250
- Arp create 252
- Use the following screen to display or edit entries in the static arp table entries added to this table are retained until the associated ip interface is deleted or the switch is reset to the factory defaults 252
- Bootp dhcp relay agent 256
- Broadcasts the dhcp request again to another directly attached ip subnet specified in the switch 256
- Configuration 256
- Forwards the packet to a preferred server as defined in the switch configuration using unicast routing or 256
- If a dhcp server is not located in the same subnet with a host you can configure this switch to forward any host configuration queries to a server located on another subnet or on another network depending on the configuration setup the switch either 256
- Specify the address for any dhcp server or specify the subnet address for an outbound ip interface already configured on this switch as described in the following screens 256
- Router discovery 258
- Router discovery configuration 258
- Router discovery status 260
- Ip multicast 269
- Multicast 269
- Multicast global configuration 269
- Multicast interface configuration 270
- Multicast mroute summary 271
- Multicast static routes configuration 272
- Multicast static routes summary 273
- Multicast admin boundary configuration 274
- Multicast admin boundary summary 275
- Igmp global configuration 276
- Igmp interface configuration 277
- Igmp interface configuration summary 279
- Igmp cache information 281
- Igmp interface membership details info 282
- Dvmrp global configuration 284
- Dvmrp interface configuration 285
- Dvmrp configuration summary 287
- Dvmrp next hop summary 289
- Dvmrp prune summary 290
- Dvmrp route summary 291
- Mdebug 292
- Mrinfo run 292
- Mrinfo show 293
- Mstat run 294
- Mstat show 295
- Mtrace configuration 296
- Mtrace run 297
- Mtrace show 298
- Pim dm 299
- Help for pim dm interface configuration 300
- Pim dm global configuration 300
- Help for pim dm interface summary 301
- Pim sm 303
- Pim sm global configuration 303
- Pim sm global parameters 304
- Pim sm interface configuration 305
- Pim sm interface summary 307
- Pim sm component summary 308
- Pim sm rp set summary 309
- Pim sm candidate rp summary 310
- Pim sm static rp configuration 310
- Command 312
- Command structure 312
- Format 312
- Parameters 312
- Values 312
- Annotations 313
- Conventions 313
- Quick start up 314
- Quick starting the switch 314
- System info and system setup 314
- Command details 317
- Mode based cli 319
- Mode based topology 319
- Mode based topology 320
- Accessing to all commands in the privileged exec mode and below is restricted through a password 321
- Commands the command prompt shown at this level is 321
- Figure 7 1 mode based cli 321
- In the privileged exec mode 321
- Mode based command hierarchy 321
- Particular mode with the exception of the user exec mode commands the user exec mode commands may also be executed 321
- Prompt displays a list of the available commands and descriptions of the commands 321
- The cli is divided into various modes the commands in one mode are not available until the operator switches to that 321
- The cli provides the following modes 321
- The commands available to the operator at any point in time depend upon the mode entering a question mark at the cli 321
- User exec mode 321
- User s manual of wgs3 2820 wgs3 5220 321
- When the operator logs into the cli the user exec mode is the initial mode the user exec mode contains a limited set of 321
- Flow of operation 322
- Flow of operation 323
- Behavior of command help 324
- No form of a command 324
- Support for no form 324
- Cli commands base 325
- Show arp switch 325
- Show eventlog 325
- System information and statistics commands 325
- Show hardware 326
- Show interface 326
- Show interface ethernet 327
- Show logging 331
- Show mac addr table 332
- Show msglog 332
- Management vlan commands 333
- Network mgmt_vlan 333
- Show running config 333
- Show sysinfo 333
- Snmp server 333
- Classofservice dot1pmapping 334
- Dot1p commands 334
- Lag port channel 802 ad commands 334
- Port channel staticcapability 334
- Show classofservice dot1pmapping 334
- Vlan port priority all 334
- Vlan priority 334
- Bridge aging time 335
- Management commands 335
- No bridge aging time 335
- No port channel staticcapability 335
- Show port channel brief 335
- Network javamode 336
- Network mac address 336
- Network mac type 336
- No mtu 336
- No network javamode 336
- Network parms 337
- Network protocol 337
- No network mac type 337
- No remotecon maxsessions 337
- Remotecon maxsessions 337
- Remotecon timeout 337
- No remotecon timeout 338
- No serial baudrate 338
- No serial timeout 338
- Serial baudrate 338
- Serial timeout 338
- Set prompt 339
- Show forwardingdb agetime 339
- Show network 339
- Show remotecon 340
- Show serial 340
- Show snmpcommunity 340
- Show snmptrap 341
- Show trapflags 341
- No snmp server community 342
- No snmp server community ipaddr 342
- Snmp server community 342
- Snmp server community ipaddr 342
- No snmp server community ipmask 343
- No snmp server community mode 343
- Snmp server community ipmask 343
- Snmp server community mode 343
- Snmp server community ro 343
- No snmp server enable traps 344
- No snmp server enable traps bcaststorm 344
- No snmp server enable traps linkmode 344
- Snmp server community rw 344
- Snmp server enable traps 344
- Snmp server enable traps bcaststorm 344
- Snmp server enable traps linkmode 344
- No snmp server enable traps multiusers 345
- No snmp server enable traps stpmode 345
- No snmptrap 345
- Snmp server enable traps multiusers 345
- Snmp server enable traps stpmode 345
- Snmptrap 345
- No snmptrap mode 346
- No telnet 346
- Snmptrap ipaddr 346
- Snmptrap mode 346
- Telnet 346
- Addport 347
- Auto negotiate 347
- Auto negotiate all 347
- Delete interface 347
- Device configuration commands 347
- Deleteport 348
- Macfilter 348
- Macfilter adddest 348
- No macfilter 348
- No macfilter adddest 348
- Macfilter adddest all 349
- Macfilter addsrc 349
- Macfilter addsrc all 349
- No macfilter adddest all 349
- No macfilter addsrc 349
- No macfilter addsrc all 349
- Monitor session 350
- Monitor session mode 350
- No monitor session 350
- No monitor session mode 350
- Port lacpmode 350
- No port channel adminmode 351
- No port lacpmode 351
- No port lacpmode all 351
- Port channel 351
- Port channel adminmode 351
- Port lacpmode all 351
- No port channel linktrap 352
- No protocol group 352
- Port channel linktrap 352
- Port channel name 352
- Protocol group 352
- Protocol vlan group 352
- No protocol vlan group 353
- No protocol vlan group all 353
- No set garp timer join 353
- Protocol vlan group all 353
- Set garp timer join 353
- No set garp timer join all 354
- No set garp timer leave 354
- Set garp timer join all 354
- Set garp timer leave 354
- Set garp timer leave all 354
- No set garp timer leave all 355
- No set garp timer leaveall 355
- Set garp timer leaveall 355
- Set garp timer leaveall all 355
- No set garp timer leaveall all 356
- No set gmrp adminmode 356
- No set gmrp interfacemode 356
- Set gmrp adminmode 356
- Set gmrp interfacemode 356
- No set gmrp interfacemode all 357
- No set gvrp adminmode 357
- No set gvrp interfacemode 357
- Set gmrp interfacemode all 357
- Set gvrp adminmode 357
- Set gvrp interfacemode 357
- No set gvrp interfacemode all 358
- Set gvrp interfacemode all 358
- Show description 358
- Show garp 358
- Show gmrp configuration 358
- Show gvrp configuration 359
- Show igmpsnooping 360
- Show mac address table gmrp 360
- Show mac address table igmpsnooping 360
- Show mac address table multicast 361
- Show mac address table static 361
- Show mac address table staticfiltering 361
- Show mac address table stats 362
- Show monitor 362
- Show port 362
- Show port channel 363
- Show port protocol 363
- Show storm control 364
- Show vlan 364
- Show vlan brief 365
- Show vlan port 365
- No shutdown 366
- No shutdown all 366
- No snmp trap link status 366
- Shutdown 366
- Shutdown all 366
- Snmp trap link status 366
- Snmp trap link status all 366
- Description 367
- No snmp trap link status all 367
- No spanning tree bpdumigrationcheck 367
- Spanning tree 367
- Spanning tree bpdumigrationcheck 367
- Speed all 368
- Storm control broadcast 368
- No storm control broadcast 369
- No storm control flowcontrol 369
- No vlan 369
- Storm control flowcontrol 369
- No vlan acceptframe 370
- No vlan ingressfilter 370
- Vlan acceptframe 370
- Vlan ingressfilter 370
- Vlan makestatic 370
- No vlan name 371
- Vlan name 371
- Vlan participation 371
- Vlan participation all 371
- Vlan port acceptframe all 371
- No vlan port acceptframe all 372
- No vlan port ingressfilter all 372
- No vlan port pvid all 372
- No vlan port tagging all 372
- Vlan port ingressfilter all 372
- Vlan port pvid all 372
- Vlan port tagging all 372
- No vlan protocol group add protocol 373
- No vlan pvid 373
- Vlan protocol group 373
- Vlan protocol group add protocol 373
- Vlan protocol group remove 373
- Vlan pvid 373
- Disconnect 374
- No vlan tagging 374
- Show loginsession 374
- Show users 374
- User account management commands 374
- Vlan tagging 374
- No users name 375
- No users passwd 375
- Users name 375
- Users passwd 375
- No users snmpv3 accessmode 376
- No users snmpv3 authentication 376
- Users snmpv3 accessmode 376
- Users snmpv3 authentication 376
- Users snmpv3 encryption 376
- Clear config 377
- Clear counters 377
- Clear igmpsnooping 377
- Clear pass 377
- Clear port channel 377
- No users snmpv3 encryption 377
- System utilities 377
- Clear traplog 378
- Clear vlan 378
- Logout 379
- Reload 379
- Access list 380
- Cli commands access control list 380
- Cli commands quality of service 380
- Configuration commands 380
- Show ip access lists 380
- Cli commands differentiated services 381
- Ip access group 381
- Ip access group all 381
- No access list 381
- Class commands 383
- Class map 383
- Diffserv 383
- No diffserv 383
- Class map rename 384
- Match any 384
- Match class map 384
- No class map 384
- Match destination address mac 385
- Match dstip 385
- No match class map 385
- Match dstl4port 386
- Match ip dscp 386
- Match ip precedence 386
- Match ip tos 387
- Match protocol 387
- Match source address mac 388
- Match srcip 388
- Match srcl4port 388
- Bandwidth kbps 389
- Match vlan 389
- Policy commands 389
- Bandwidth percent 390
- Expedite kbps 390
- No class 390
- Expedite percent 391
- Mark ip dscp 391
- Mark ip precedence 392
- Police simple 392
- Police single rate 392
- Police two rate 393
- Policy map 393
- No policy map 394
- Policy map rename 394
- Randomdrop 394
- Shape bps average 395
- Shape bps peak 395
- Service commands 396
- Service policy 396
- Show class map 397
- Show commands 397
- Show diffserv 398
- Show policy map 398
- Show diffserv service 400
- Show diffserv service brief 400
- Show policy map interface 401
- Rate limiting 402
- Rate limiting commands 402
- Show service policy 402
- Show rate limiting 403
- Authentication login 404
- Clear dot1x statistics 404
- Cli commands security 404
- No authentication login 404
- Security commands 404
- Clear radius statistics 405
- Dot1x defaultlogin 405
- Dot1x initialize 405
- Dot1x login 405
- Dot1x max req 405
- No dot1x max req 405
- 0 dot1x re authenticate 406
- 1 dot1x re authentication 406
- Dot1x port control 406
- Dot1x port control all 406
- No dot1x port control 406
- 1 no dot1x re authentication 407
- 2 dot1x system auth control 407
- 2 no dot1x system auth control 407
- 3 dot1x timeout 407
- 3 no dot1x timeout 408
- 4 dot1x user 408
- 4 no dot1x user 408
- 5 no radius accounting mode 408
- 5 radius accounting mode 408
- 6 radius server host 408
- 6 no radius server host 409
- 7 radius server key 409
- 8 radius server msgauth 409
- 9 radius server primary 409
- 0 no radius server retransmit 410
- 0 radius server retransmit 410
- 1 no radius server timeout 410
- 1 radius server timeout 410
- 2 show accounting 410
- 3 show authentication 411
- 4 show authentication users 411
- 5 show dot1x 412
- 6 show dot1x users 413
- 7 show radius 413
- 8 show radius statistics 414
- 0 users defaultlogin 415
- 1 users login 415
- 9 show users authentication 415
- Ip ssh 415
- No ip ssh 415
- Secure shell ssh commands 415
- Http commands 416
- Ip http secure port 416
- Ip http secure protocol 416
- Ip ssh protocol 416
- No ip http secure port 416
- No ip http secure protocol 416
- Show ip ssh 416
- Ip http secure server 417
- Ip http server 417
- Mac lock 417
- Mac lock commands 417
- No ip http secure server 417
- No ip http server 417
- Show ip http 417
- No mac lock 418
- Show mac lock 418
- Cli commands switching 419
- Show spanning tree 419
- Spanning tree commands 419
- Show spanning tree interface 420
- Show spanning tree mst detailed 420
- Show spanning tree mst port detailed 420
- Show spanning tree mst port summary 421
- Show spanning tree mst summary 422
- Show spanning tree summary 422
- Show spanning tree vlan 422
- 0 no spanning tree configuration name 423
- 0 spanning tree configuration name 423
- 1 no spanning tree configuration revision 423
- 1 spanning tree configuration revision 423
- 2 spanning tree edgeport 423
- No spanning tree 423
- Spanning tree 423
- 2 no spanning tree edgeport 424
- 3 no spanning tree forceversion 424
- 3 spanning tree forceversion 424
- 4 no spanning tree forward time 424
- 4 spanning tree forward time 424
- 5 spanning tree hello time 424
- 5 no spanning tree hello time 425
- 6 no spanning tree max age 425
- 6 spanning tree max age 425
- 7 no spanning tree mst 425
- 7 spanning tree mst 425
- 8 no spanning tree mst instance 426
- 8 spanning tree mst instance 426
- 9 no spanning tree mst priority 426
- 9 spanning tree mst priority 426
- 0 no spanning tree mst vlan 427
- 0 spanning tree mst vlan 427
- 1 no spanning tree port mode 427
- 1 spanning tree port mode 427
- 2 no spanning tree port mode all 427
- 2 spanning tree port mode all 427
- Address resolution protocol arp commands 428
- Cli commands routing 428
- No arp 428
- Arp cachesize 429
- Arp dynamicrenew 429
- Ip proxy arp 429
- No arp cachesize 429
- No ip proxy arp 429
- 0 arp resptime 430
- 1 no arp resptime 430
- 2 arp retries 430
- 3 no arp retries 430
- Arp purge 430
- No arp dynamicrenew 430
- 4 arp timeout 431
- 5 no arp timeout 431
- 6 clear arp cache 431
- 7 show arp 431
- 8 show arp brief 432
- 9 show arp switch 433
- Ip routing 433
- Ip routing commands 433
- No routing 433
- This section describes the commands you use to enable and configure ip routing on the switch 433
- Ip route 434
- No ip address 434
- No ip routing 434
- 0 no ip route default 435
- 1 ip route distance 435
- Ip route default 435
- No ip route 435
- 2 no ip route distance 436
- 3 ip forwarding 436
- 4 no ip forwarding 436
- 5 ip netdirbcast 436
- 6 no ip netdirbcast 436
- 7 ip mtu 437
- 8 no ip mtu 437
- 0 show ip brief 438
- 1 show ip interface 438
- 9 encapsulation 438
- 2 show ip interface brief 439
- Active state active 439
- Encapsulation type ethernet 439
- Forward net directed broadcasts disable 439
- Interface configuration status enable 439
- Ip mtu 1500 439
- Link speed data rate 100 full 439
- Local proxy arp disable 439
- Mac address 00 10 4b d2 17 83 439
- Proxy arp enable 439
- Routing configuration enable 439
- Routing show ip interface 0 2 439
- 3 show ip route 440
- 4 show ip route summary 441
- 5 show ip route preferences 441
- 6 show ip stats 442
- Ip irdp 442
- Ip irdp address 442
- Router discovery protocol commands 442
- The configuration of nssa preferences is not supported in this release 442
- This command enables router discovery on an interface 442
- Ip irdp holdtime 443
- Ip irdp maxadvertinterval 443
- Ip irdp minadvertinterval 443
- No ip irdp address 443
- No ip irdp holdtime 443
- No ip irdp maxadvertinterval 443
- Ip irdp preference 444
- No ip irdp minadvertinterval 444
- No ip irdp preference 444
- Show ip irdp 444
- Ip vrrp global config 445
- Show ip vlan 445
- Virtual lan routing commands 445
- Virtual router redundancy protocol commands 445
- Vlan routing 445
- Ip vrrp interface config 446
- Ip vrrp ip 446
- Ip vrrp mode 446
- No ip vrrp 446
- No ip vrrp mode 446
- Ip vrrp authentication 447
- Ip vrrp preempt 447
- No ip vrrp authentication 447
- No ip vrrp ip 447
- No ip vrrp preempt 447
- Ip vrrp priority 448
- Ip vrrp timers advertise 448
- No ip vrrp priority 448
- No ip vrrp timers advertise 448
- Show ip vrrp interface stats 448
- 0 show ip vrrp 449
- 1 show ip vrrp interface 449
- 2 show ip vrrp interface brief 450
- Bootpdhcprelay cidoptmode 450
- Dhcp and bootp relay commands 450
- Bootpdhcprelay enable 451
- Bootpdhcprelay maxhopcount 451
- Bootpdhcprelay minwaittime 451
- No bootpdhcprelay cidoptmode 451
- No bootpdhcprelay enable 451
- No bootpdhcprelay maxhopcount 451
- Bootpdhcprelay serverip 452
- No bootpdhcprelay minwaittime 452
- No bootpdhcprelay serverip 452
- Show bootpdhcprelay 452
- 1583compatibility 453
- Enable ospf 453
- Ip ospf 453
- No enable ospf 453
- No ip ospf 453
- Open shortest path first ospf commands 453
- Router ospf 453
- Area default cost ospf 454
- Area nssa default info originate ospf 454
- Area nssa ospf 454
- No 1583compatibility 454
- No area nssa 454
- No area nssa default info originate ospf 454
- 0 area nssa translator role ospf 455
- Area nssa no redistribute ospf 455
- Area nssa no summary ospf 455
- No area nssa no redistribute ospf 455
- No area nssa no summary ospf 455
- No area nssa translator role ospf 455
- 1 area nssa translator stab intv ospf 456
- 2 area range ospf 456
- 3 area stub ospf 456
- No area nssa translator stab intv ospf 456
- No area range 456
- No area stub 456
- 4 area stub no summary ospf 457
- 5 area virtual link ospf 457
- 6 area virtual link authentication 457
- No area stub no summary 457
- No area virtual link 457
- 7 area virtual link dead interval ospf 458
- 8 area virtual link hello interval ospf 458
- 9 area virtual link retransmit interval ospf 458
- No area virtual link authentication 458
- No area virtual link dead interval 458
- No area virtual link hello interval 458
- 0 area virtual link transmit delay ospf 459
- 1 default information originate ospf 459
- 2 default metric ospf 459
- No area virtual link retransmit interval 459
- No area virtual link transmit delay 459
- No default information originate ospf 459
- 3 distance ospf ospf 460
- 4 distribute list out ospf 460
- No default metric ospf 460
- No distance ospf 460
- No distribute list out 460
- 5 exit overflow interval ospf 461
- 6 external lsdb limit ospf 461
- 7 ip ospf areaid 461
- No exit overflow interval 461
- No external lsdb limit 461
- 0 ip ospf dead interval 462
- 8 ip ospf authentication 462
- 9 ip ospf cost 462
- No ip ospf authentication 462
- No ip ospf cost 462
- No ip ospf dead interval 462
- 1 ip ospf hello interval 463
- 2 ip ospf priority 463
- 3 ip ospf retransmit interval 463
- No ip ospf hello interval 463
- No ip ospf priority 463
- No ip ospf retransmit interval 463
- 4 ip ospf transmit delay 464
- 5 ip ospf mtu ignore 464
- 6 router id ospf 464
- No ip ospf mtu ignore 464
- No ip ospf transmit delay 464
- 0 trapflags ospf 465
- 7 redistribute ospf 465
- 8 maximum paths ospf 465
- 9 timers spf 465
- No maximum paths 465
- No redistribute 465
- 1 show ip ospf 466
- No trapflags 466
- 2 show ip ospf abr 467
- 3 show ip ospf area 468
- 4 show ip ospf asbr 469
- 5 show ip ospf database 469
- 6 show ip ospf database database summary 470
- 8 show ip ospf interface 471
- The information below will only be displayed if ospf is enabled 471
- 9 show ip ospf interface brief 472
- 0 show ip ospf interface stats 473
- 1 show ip ospf neighbor 474
- Database description 474
- Ls acknowledgement 474
- Ls request 474
- Ls update 474
- 2 show ip ospf range 476
- 3 show ip ospf statistics 477
- 4 show ip ospf stub table 477
- 5 show ip ospf virtual link 478
- 6 show ip ospf virtual link brief 478
- Auto summary 480
- Enable rip 480
- Ip rip 480
- No enable rip 480
- No ip rip 480
- Router rip 480
- Routing information protocol rip commands 480
- This command resets the default administrative mode of rip in the router active 480
- Default information originate rip 481
- Default metric rip 481
- Distance rip 481
- No auto summary 481
- No default information originate rip 481
- No default metric rip 481
- 0 ip rip receive version 482
- Distribute list out rip 482
- Ip rip authentication 482
- No distance rip 482
- No distribute list out 482
- No ip rip authentication 482
- This command sets the default rip version 2 authentication type for an interface 482
- 1 ip rip send version 483
- 2 hostroutesaccept 483
- 3 split horizon 483
- No hostroutesaccept 483
- No ip rip receive version 483
- No ip rip send version 483
- Received 483
- This command configures the interface to allow rip control packets of the default version s to be 483
- 4 redistribute rip 484
- 5 show ip rip 484
- No redistribute 484
- No split horizon 484
- 6 show ip rip interface brief 485
- 7 show ip rip interface 485
- Cli commands ip multicast 487
- Ip mcast boundary 487
- Ip multicast 487
- Multicast commands 487
- No ip mcast boundary 487
- No ip multicast 487
- The following commands are used to configure ip multicast 487
- Ip multicast staticroute 488
- Ip multicast ttl threshold 488
- Mrinfo 488
- No ip multicast staticroute 488
- No ip multicast ttl threshold 488
- Mtrace 489
- Show ip mcast 489
- 0 show ip mcast interface 490
- Show ip mcast boundary 490
- 1 show ip mcast mroute 491
- 2 show ip mcast mroute group 491
- 3 show ip mcast mroute source 492
- 4 show ip mcast mroute static 493
- 5 show mrinfo 493
- 6 show mstat 493
- 7 show mtrace 494
- Distance vector multicast routing protocol dvmrp commands 495
- Ip dvmrp 495
- Ip dvmrp metric 495
- Ip dvmrp trapflags 495
- No ip dvmrp 495
- No ip dvmrp metric 495
- No ip dvmrp trapflags 496
- Show ip dvmrp 496
- Show ip dvmrp interface 496
- Show ip dvmrp neighbor 497
- Show ip dvmrp nexthop 498
- Show ip dvmrp prune 498
- Show ip dvmrp route 499
- Internet group management protocol igmp commands 500
- Ip igmp 500
- Ip igmp version 500
- No ip igmp 500
- No ip igmp version 500
- Set igmp mcrtrexpiretime 500
- Igmp last member query interval 501
- Ip igmp last member query count 501
- Ip igmp query interval 501
- No ip igmp last member query count 501
- No ip igmp last member query interval 501
- No set igmp mcrtrexpiretime 501
- Ip igmp query max response time 502
- Ip igmp robustness 502
- Ip igmp startup query count 502
- No ip igmp query interval 502
- No ip igmp query max response time 502
- No ip igmp robustness 502
- 0 ip igmp startup query interval 503
- 1 set igmp groupmembershipinterval 503
- No ip igmp startup query count only for layer 3 series 503
- No ip igmp startup query interval 503
- No set igmp groupmembershipinterval 503
- 2 set igmp maxresponse 504
- 3 set igmp mrouter interface 504
- 4 set igmp mrouter 504
- No set igmp maxresponse 504
- No set igmp mrouter 504
- No set igmp mrouter interface 504
- 5 show ip igmp 505
- 6 show ip igmp groups 505
- 7 show ip igmp interface 506
- 8 show ip igmp interface membership 507
- 9 show ip igmp interface stats 508
- Ip pimdm 509
- Ip pimdm mode 509
- Ip pimdm query interval 509
- No ip pimdm 509
- No ip pimdm mode 509
- Protocol independent multicast dense mode pim dm commands 509
- No ip pimdm query interval 510
- Show ip pimdm 510
- Show ip pimdm interface 510
- Show ip pimdm interface stats 510
- Show ip pimdm componenttable 511
- Show ip pimdm neighbor 511
- Ip pimsm cbsrhashmasklength 512
- Ip pimsm cbsrpreference 512
- Ip pimsm crppreference 512
- No ip pimsm cbsrhashmasklength 512
- No ip pimsm cbsrpreference 512
- Protocol independent multicast sparse mode pim sm commands 512
- Ip pimsm 513
- Ip pimsm message interval 513
- No ip pimsm 513
- No ip pimsm crppreference 513
- No ip pimsm message interval 513
- Ip pimsm mode 514
- Ip pimsm query interval 514
- Ip pimsm spt threshold 514
- No ip pimsm mode 514
- No ip pimsm query interval 514
- No ip pimsm spt threshold 514
- 0 ip pimsm staticrp 515
- 1 ip pimsm register rate limit 515
- Ip pim trapflags 515
- No ip pim trapflags 515
- No ip pimsm staticrp 515
- 2 show ip pimsm rphash 516
- 3 show ip pimsm staticrp 516
- 4 show ip pimsm 516
- This command displays the static rp information for the pim sm router 516
- 5 show ip pimsm componenttable 517
- 6 show ip pimsm interface 517
- 7 show ip pimsm interface stats 518
- 8 show ip pimsm neighbor 518
- 0 show ip pimsm rphash 519
- 9 show ip pimsm rp 519
- Address table 520
- Forwarding filtering 520
- Learning 520
- Store and forward 520
- Switch operation 520
- Auto negotiation 521
- Trouble shooting 522
- A 10 100mbps 10 100base tx 523
- A switch s rj 45 pin assignments 523
- Appendex a 523
- Figure a 1 straight through and crossover cable 524
- Into your network 524
- Of straight cable and crossover cable connection 524
- Orange 524
- Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables 524
- Side 1 524
- Side 2 524
- Straight cable side 1 side2 524
- The standard rj 45 receptacle connector 524
- There are 8 wires on a standard utp stp cable and each wire is color coded the following shows the pin allocation and color 524
- User s manual of wgs3 2820 wgs3 5220 524
- White blue 524
- White brown 524
- White green 524
- White orange 524
- Glossary 525
- Management information base mib 527
- Multicast switching 527
- Open shortest path first ospf 527
- Out of band management 527
- Port mirroring 527
- Port trunk 527
- Remote monitoring rmon 527
- Routing information protocol rip 527
- Simple network management protocol snmp 527
- Serial line internet protocol slip 528
- Spanning tree protocol stp 528
- Telnet 528
- Trivial file transfer protocol tftp 528
- Virtual lan vlan 528
- Xmodem 528
Похожие устройства
- Gorenje IT630BC Инструкция по эксплуатации
- Planet WGS3-5220 Инструкция по эксплуатации
- Gorenje ECT2800P2 Инструкция по эксплуатации
- Planet WGS3-24240 Инструкция по эксплуатации
- Gorenje ECT2700P2 Инструкция по эксплуатации
- Asus RT-N15U Инструкция по эксплуатации
- Planet VC-2400MR Инструкция по эксплуатации
- Gorenje ECT2600P2 Инструкция по эксплуатации
- Asus RT-N56U Инструкция по эксплуатации
- Planet VC-2400MR48 Инструкция по эксплуатации
- Gorenje ECS680AC Инструкция по эксплуатации
- Asus RT-N53 Инструкция по эксплуатации
- Planet VC-820M Инструкция по эксплуатации
- Gorenje ECS680BXC Инструкция по эксплуатации
- Asus WL-330N 3G Инструкция по эксплуатации
- Planet WGSD-8020 Инструкция по эксплуатации
- Gorenje ECS680AX Инструкция по эксплуатации
- Gorenje G6N50RW Инструкция по эксплуатации
- Planet FGSD-1022 Инструкция по эксплуатации
- Planet FGSD-1022P Инструкция по эксплуатации