Home
Главная
Hitachi
Сетевая торцовочная пила
C8FSHENA
Инструкция по эксплуатации Страница: 16

Hitachi C8FSHENA [16/102] English

English

3. Extention cord

When the work area is removed from the power source, use an extension

cord of sufficient thickness and rated capacity. The extension cord should be

kept as short as practicable.

4. When the power tool is prepared for shipping, its main parts are secured by

a locking pin

Move the handle slightly so that the locking pin can be disengaged.

During transport, lock the locking pin into the gear case (Fig. 4).

5. Attach the dust bag to the main unit (Fig. 1)

6. Installation

Ensure that the machine is always fixed to bench.

Attach the power tool to a level, horizontal work bench.

Select 8 mm diameter bolts suitable in length for the thickness of the work

bench.

Bolt length should be at least 25 mm plus the thickness of the work bench.

For example, use 8 mm × 65 mm bolts for a 25 mm thick work bench.

ADJUSTING THE POWER TOOL PRIOR TO USE

CAUTION

Make all necessary adjustments before inserting the plug in the power source.

1. Check to see that the lower guard operates smoothly

CAUTION

䡬

This slide compound miter saw is equipped with a saw head lock as safety

device.

䡬

To lower the saw head to cut, the lock must be released by pressing the lock

lever with your thumb.

(1) When you push down the handle while pushing the lock lever, check that

the lower guard revolves smoothly (Fig. 5).

(2) Next, check that the lower guard returns to the original position when the

handle is raised.

2. Checking the saw blade lower limit position (Fig. 6 and Fig. 7)

Check that the saw blade can be lowered 10 mm to 11 mm below the table

insert.

When you replace a saw blade with a new one, adjust the lower limit position

so that the saw blade will not cut the turntable or complete cutting cannot

be done.

To adjust the lower limit position of the saw blade, follow the procedure (1)

indicated below. (Fig. 7)

Furthermore, when changing the position of a 8 mm depth adjustment bolt

that serves as a lower limit position stopper of the saw blade.

(1) Turn the 8 mm depth adjustment bolt, change the height where the bolt

head and the hinge contacts, and adjust the lower limit position of the saw

blade.

NOTE

Confirm that the saw blade is adjusted so that it will not cut into the turntable.

3. Lower limit position of saw blade when cutting a large workpiece

NOTE

When cutting a workpiece exceeding 65 mm in height in right-angle cutting

or 60 mm in left bevel angle cutting or 45 mm in right bevel angle cutting,

adjust the lower limit position so that the base of the motor head (Fig. 6) will

not come in contact with the workpiece.

PRACTICAL APPLICATIONS

WARNING

䡬

To avoid personal injury, never remove or place a workpiece on the table

while the tool is being operated.

䡬

Never place your limbs inside of the line next to warning sign while the tool

is being operated. This may cause hazardous conditions (See Fig. 8).

CAUTION

䡬

It is dangerous to remove or install the workpiece while the saw blade is

turning.

䡬

When sawing, clean off the shavings from the turntable.

䡬

If the shavings accumulate too much, the saw blade from the cutting material

will be exposed. Never subject your hand or anything else to go near the

exposed blade.

1. Tightly secure the material by vise assembly to be cut so that it does not

move during cutting

2. Switch operation

Pulling the trigger turns the switch on. Releasing the trigger turns the switch

off.

3. Base holder adjustment (Fig. 3)

Loosen the 6 mm bolt with the supplied 10 mm box wrench. Adjust the base

holder until its bottom surface contacts the bench or the floor surface.

After adjustment, firmly tighten the 6 mm bolt.

4. Using the Vise Assembly (Standard accessory) (Fig. 9)

(1) The vise assembly can be mounted on either the left fence {Fence (B)} or the

right fence {Fence (A)} by loosening the 6 mm wing bolt (A).

(2) The screw holder can be raised or lowered according to the height of the

workpiece by loosening the 6 mm wing bolt (B). After the adjustment, firmly

tighten the 6 mm wing bolt (B) and fix the screw holder.

(3) Turn the upper knob and securely fix the workpiece in position.

WARNING

䡬

Always firmly clamp or vise to secure the workpiece to the fence; otherwise

the workpiece might be thrust from the table and cause bodily harm.

CAUTION

䡬

Always confirm that the motor head does not contact the vise assembly

when it is lowered for cutting. If there is any danger that it may do so, loosen

the 6 mm wing bolt and move the vise assembly to a position where it will

not contact the saw blade.

5. Positioning the table insert (Fig. 1)

Table inserts are installed on the turntable. When shipping the tool from the

factory, the table inserts are so fixed that the saw blade does not contact

them. The burr of the bottom surface of the workpiece is remarkably reduced,

if the table insert is fixed so that the gap between the side surface of the

table insert and the saw blade will be minimum. Before using the tool,

eliminate this gap in accordance with the following procedure.

(1) Right angle cutting

Loosen the three 6 mm machine screws, then secure the left side table insert

and temporarily tighten the 6 mm machine screws of both ends. Then fix a

workpiece (about 200 mm wide) with the vise assembly and cut it off. After

aligning the cutting surface with the edge of the table insert, securely tighten

the 6 mm machine screws of both ends. Remove the workpiece and securely

tighten the 6 mm center machine screw. Adjust the right hand table insert in

the same way.

(2) Left and right bevel angle cutting

Adjust the table insert in the manner same procedure for right angle cutting.

CAUTION

䡬

After adjusting the table insert for right angle cutting, the table insert will be

cut to some extent if it is used for bevel angle cutting.

When bevel cutting operation is required, adjust the table insert for bevel

angle cutting.

6. Confirmation for use of sub fence (Optional accessory)

This power tool is equipped with a sub fence. In the case of direct angle

cutting and right bevel angle cutting, use the sub fence. Then, you can do

Left bevel angle cutting, Right bevel angle cutting and Direct angle cutting

and realize stable cutting of the material with a wide back face.

WARNING

䡬

In the case of left bevel cutting, turn the sub fence counterclockwise (Fig.

10). Unless it is turned counterclockwise, the main body or saw blade may

contact the sub fence, resulting in an injury.

7. Using an ink line

Upon lowering the motor section, the lower guard is raised and the saw

blade appears.

Align the ink line with the saw blade.

CAUTION

Never lift the lower guard while the saw blade is rotating.

The sub fence will not only make contact and adversely affect cutting

accuracy, this could also result in damage to the guard.

Содержание

Похожие устройства

English 3 Extention cord When the work area is removed from the power source use an extension cord of sufficient thickness and rated capacity The extension cord should be kept as short as practicable 4 When thepower tool is prepared for shipping its main parts are secured by a locking pin Move the handle slightly so that the locking pin can be disengaged During transport lockthe locking pin into the gear case Fig 41 5 Attach the dust bag to the main unit Fig 11 6 Installation Ensure th at the machine is always fixed to bench Attach the power tool to a level horizontal work bench O If the shavings accumulate toomuch thesaw blade from th e cutting material will be exposed Never subject your hand or anything else to go near the exposed blade 1 Tightly secure the material by vise assembly to be cut so that it does not move during cutting 2 Switch operation Pulling thetrigger turns the switch on Releasing the trigger turnsthe switch off 3 Base holder adjustment Fig 3 Loosen the 6 mm bolt with the supplied 10 mm box wrench Adjustthe base holder until its bottom surface contacts the bench orthe floor surface After adjustment firmly tighten the 6 mm bolt Select 8 mm diameter bolts suitable in length for the thickness of the work 4 Using the Vise Assembly Standard accessory Fig 9 bench 1 The vise assembly can be mounted on either the left fence Fence Bl or the Bolt length should be at least 25 mm plus the thickness of the work bench For example use 8 mm x 65 mm bolts for a 25 mm thick work bench right fence Fence A by loosening the 6 mm wing bolt A 2 The screw holder can be raised or lowered according to the height of the workpiece by loosening the 6 mm wing bolt IB After the adjustment firmly ADJUSTING THE POWER TOOL PRIOR TO USE CAUTION Makeall necessary adjustments before inserting the plug in the power source 1 Check to see that the lowerguard operates smoothly tighten the 6 mm wing bolt B and fix the screw holder 3 Turn the upper knob and securely fix the workpiece in position WARNING O Always firmly clamp or vise tosecure the workpiece to the fence otherwise the workpiece might be thrust from the table and cause bodily harm CAUTION CAUTION O This slide compound miter saw is equipped with a saw head lock as safety O Always confirm that the motor head does not contact the vise assembly device O To lower the saw head to cut the lock must be released by pressing the lock lever with your thumb 11 When you push down the handle while pushing the lock lever check that the lower guard revolves smoothly IFig 51 2 Next check that the lower guard retu ms to the original position when the handle is raised 2 Checking the saw blade lower limit position Fig 6 and Fig 7 Check that the saw blade can be lowered 10 mm to 11 mm below the table insert When you replace a saw blade with a newone adjust the lower limit position when it is lowered for cutting If there is any danger that it may do so loosen the 6 mm wing bolt and move the vise assembly to a position where it will not contact thesaw blade 5 Positioning the table insert Fig 11 Table inserts are installed on the turntable When sh ip pi ng the tool from the factory the table inserts are so fixed that the saw blade does not contact them The burr of the bottom su if ace of the workpiece is remarkably reduced if the table insert is fixed so that the gap between the side surface of the table insert and the saw blade will be minimum Before using the tool eliminate this gap in accordance with the following procedure 11 Right angle cutting so that the saw blade will not cut the turntable or complete cutting cannot Loosen the three 6 mm machine screws then secure the leftsidetab Ie insert be done and temporarily tighten the 6 mm mach ine screws of both ends Then fix a To adjust the lower limit position of the saw blade follow the procedure I1 workpiece about 200 mm wide with the vise assembly and cut it off After indicated below IFig 7 aligning the cutting su dace with the edge of the table insert secu rely tighten Furthermore when changing the position of a 8 mm depth adjustment bolt the 6 mm machine screws of both ends Removethe workpiece and secu rely that serves as a lower limit position stopper of the saw blade tighten the 6 mm center machine screw Adjustthe right hand table insert in 1 Turn the 8 mm depth adjustment bolt change the height where the bolt head and the hinge contacts and adjust the lower limit position of the saw blade NOTE Confirm thatthesaw blade isadjustedsothat it will not cut intothe turntable the same way 2 Left and right bevel angle cutting Adjust the table insert in the manner same procedure for rightangle cutting CAUTION O After adjusting the table insert for right angle cutting the table insert will be 3 Lower limit position of saw blade when cutting a large workpiece cut to some extent if it is used for bevel angle cutting NOTE When bevel cutting operation is required adjust the table insert for bevel When cutting a workpiece exceeding 65 mm in height in right angle cutting or 60 mm in left bevel angle cutting or 45 mm in right bevel angle cutting angle cutting 6 Confirmation for use of sub fence Optional accessory adjust the lower limit position so that the base of the motor head I Fig 6 will This power tool is equipped with a sub fence In the case of direct angle not come in contact with the workpiece cutting and right bevel angle cutting use the sub fence Then you can do Left bevel angle cutting Right bevel angle cutting and Direct angle cutting PRACTICAL APPLICATIONS WARNING O To avoid personal injury never remove or place a workpiece on the table while the tool is being operated O Never place your limbs inside of the line next to warning sign wh ile the tool is being operated This may cause hazardous conditions See Fig 8 CAUTION O It is dangerous to remove or install the workpiece while the saw blade is turning O When sawing clean off the shavings from the turntable and realize stable cutting of the material with a wide back face WARNING O In the case of left bevel cutting turn the sub fence counterclockwise Fig 10 Unless it is turned counterclockwise the main body or saw blade may contact the sub fence resulting in an injury 7 Using an ink line Upon lowering the motor section the lower guard is raised and the saw blade appears Align the ink line with the saw blade CAUTION Never lift the lower guard while the saw blade is rotating The sub fence will not only make contact and adversely affect accuracy th is could also result in damage to the guard 15 cutting

Скачать