Skil 0735 RA [7/108] Maintenance service

Skil 0735 RA [7/108] Maintenance service
7
Always ensure that the ventilation openings are kept clear
of debris
AFTER USE
• Alwaysswitchofftoolanddisconnectplugfrom
powersourcebeforemakingadjustments,changing
spools,cleaningorleavingthetoolunattendedfor
anyperiod
Store the tool indoors in a dry and locked-up place, out
of reach of children
EXPLANATIONOFSYMBOLSONTOOL
3Warning! Read the instruction manual
4 Do not expose tool to rain
5 Wear protective glasses
6 Payattentiontotheriskofinjurycausedbyflying
debris (keep bystanders a safe distance away from work
area)
7 Immediately disconnect the plug if the (extension) cord is
damaged or cut through while working
8 Double insulation (no earth wire required)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
USE
Cutting guard 0
- mount cutting guard A as illustrated with round head
screw supplied
! neverusethetoolwithoutcuttingguardA
Cord restraint !
- hook the loop in the extension cord over restraint B as
illustrated
- pull tight to secure the extension cord
On/o @
- switch on tool by pressing trigger switch C
- switch o tool by releasing trigger switch C
! afterswitchingoffthetoolthecuttinglines
continuetorotateforafewseconds
- allow the cutting lines to stop rotating before switching
on again
! donotrapidlyswitchonandoff
Trimming
! ensurethattheredcoverD2isremovedfrom
thelinecuttingbladebeforeusingthetool
! ensurethatthecuttingareaisfreeofstones,
debrisandotherforeignobjects
! starttrimmingonlywhentoolrunsatfullspeed
- start trimming near the mains socket and move away
while working
- cut long grass in layers (always start from the top)
- only trim with the tip of the cutting line
- do not cut damp or wet grass
- prevent the cut grass from clogging the spool (do not
make heavy cuts)
- do not overload the tool
- carefully cut around trees and bushes, so that they do
not come into contact with the cutting lines
- keep the tool away from solid objects in order to
protect the cutting lines against excessive wear
- be aware of the kickback forces that occur when solid
objects are touched
Holding and guiding the tool #
- for cutting long grass slowly swing the tool from right to
left and vice versa
- for cutting shorter grass tilt the tool as illustrated
- for trimming edges turn the cutting head 180° as
illustrated
- hold tool rmly with both hands, so you will have full
control of the tool at all times
- maintain a stable working position
- always hold the tool well away from your body
Line feeding $
- tap button F lightly on the ground (preferably on a solid
surface) while the motor is running
- two cutting lines will be released and cut o to the
correct length by line cutting blade G
! ensurethattheredcoverD2isremovedfrom
thelinecuttingbladebeforeusingthetool
! takecareagainstinjuryfromlinecuttingbladeG
- after line feeding always return the tool to its normal
operating position before switching on
- feed the lines regularly to maintain full cutting circle
- when the motor runs without load and no grass is cut,
the cutting lines are worn or broken; rewind the spool
or replace the spool system
Rewinding spool %
In case the cutting lines fail to protrude from spool cap H
! switchoffthetoolanddisconnecttheplug
- remove spool system from tool and take out spool from
spool cap H
- tightly rewind both cutting lines evenly in layers in
arrow direction
- insert both lines into spool slots X and ensure that they
are securely in place (leave sucient length of line)
- thread both lines through spool holes Y before placing
the rewound spool into spool cap H
! ensurethatthespoolislocatedsecurelyinplace,
thenreleasebothlinesfromslotsXbypulling
themfirmly
- mount spool system onto tool (turnspoolclockwise
untilitclicksintoplace) ^
Replacing spool system ^
! switchoffthetoolanddisconnecttheplug
- simply remove/mount old/new spool system as
illustrated
- only use SKIL spool system 2610Z01354 with this tool
(damageduetousingotherspoolsystemswillbe
excludedfromthewarranty)
- after replacing the spool system test-run the tool for at
least one minute without load to ensure that the tool is
operating properly
! besuretoolisswitchedoffwhenpluggingin
mAINTENANCE / SERVICE
This tool is not intended for professional use
• Alwaysdisconnectplugfrompowersourcebefore
cleaningand/ormaintenance
Always keep tool and cord clean (especially the
ventilation slots)
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- clean line cutting blade G 2 and cutting guard A 2
after each use

Содержание

Always ensure that the ventilation openings are kept clear of debris AFTER USE Always switch off tool and disconnect plug from power source before making adjustments changing spools cleaning or leaving the tool unattended for any period Store the tool Indoors in a dry and locked up place out of reach of children EXPLANATION OF SYMBOLS ON TOOL Warning Read the instruction manual Do not expose tool to rain Wear protective glasses Pay attention to the risk of Injury caused by flying debris keep bystanders a safe distance away from work area 71 Immediately disconnect the plug if the extension cord is damaged or cut through while working Double insulation no earth wire required WHEN CONNECTING NEW 3 PIN PLUG U K ONLY If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug Hol ding and guidi ng the tool for cutting long grass slowly swing the tool from right to left and vice versa for cutting shorter grass tilt the tool as illustrated for trimming edges turn the cutting head 180 as illustrated hold tool firmly with both hands so you will have full control of the tool at all times maintain a stable working position always hold the tool well away from your body Line feeding tap button F lightly on the ground preferably on a solid surface while the motor is running two cutting lines will be released and cut off to the correct length by line cutting blade G I ensure that the red cover D Is removed from the line cutting blade before using the tool take care against Injury from line cutting blade G after line feeding always return the tool to its normal operating position before switching on feed the lines regularly to maintain full cutting circle when the motor runs without load and no grass is cut the cutting lines are wom or broken rewind the spool or replace the spool system Rewinding spool In case the cutting lines fail to protrude from spool cap H switch off the tool and disconnect the plug remove spool system from tool and take out spool from spool cap H tightly rewind both cutting lines evenly in layers in arrow direction insert both lines into spool slots X and ensure that they are securely in place leave sufficient length of line thread both lines through spool holesY before placing the rewound spool into spool cap H I ensure that the spool is located securely In place then release both lines from slots X by pulling them firmly mount spool system onto tool turn spool clockwise until It clicks Into place Replacing spool system switch off the tool and disconnect the plug simply remove mount old new spool system as illustrated only use SKIL spool system 2610Z01354 with this tool damage due to using other spool systems will be excluded from the warranty after replacing the spool system test run the tool for at least one minute without load to ensure that the tool is operating properly I be sure tool is switched off when plugging In USE Cutting guard mount cutting guard A as illustrated with round head screw supplied I never use the tool without cutting guard A Cord restraint hook the loop in the extension cord over restraint B as illustrated pull tight to secure the extension cord On off switch on tool by pressing trigger switch C switch off tool by releasing trigger switch C after switching off the tool the cutting lines continue to rotate for a few seconds allow the cutting lines to stop rotating before switching on again I do not rapidly switch on and off Trimming I ensure that the red cover D Is removed from the line cutting blade before using the tool I ensure that the cutting area is free of stones debris and other foreign objects start trimming only when tool runs at full speed start trimming near the mains socket and move away while working cut long grass in layers always start from the top only trim with the tip of the cutting line do not cut damp or wet grass prevent the cut grass from clogging the spool do not make heavy cuts do not werioad the tool carefully cut around trees and bushes so that they do not come into contact with the cutting lines keep the tool away from solid objects in order to protect the cutting lines against excessive wear be aware of the kickback forces that occur when solid objects are touched MAINTENANCE SERVICE This tool is not intended for professional use Always disconnect plug from power source before cleaning and or maintenance Always keep tool and cord clean especially the ventilation slots clean the tool with a damp cloth do not use cleaning agents or solvents clean line cuttin g bl ade G and cutting guard A after each use 7